HealthyAir HA-CMSC-G2-W-AEA User manual

Ceiling-Mount Aerosol Extractor
HA-CMSC-G2-W-AEA
Owner’s Manual
Table of Contents
HealthyAir® Series-1219-CM Filters
1
Important Safety Instructions
2
Technical Specifications
3
Packaging Reference
4-5
Component Reference
6-7
Installation Instructions
8-25
Electrical Wiring Instructions
26
Electrical Wiring Schematic
27
Operation Guidelines
28-29
Filter Replacement
30-34
Maintenance
35
Basic Service and Troubleshooting
36-40
1-Yeart Limited Warranty
41
Product Registration Form
42
Healthy Air Inc.
800-259-2535
www.HealthyAir.com

1
HealthyAir® Ceiling-Mount Aerosol Extractor
w/ Articulating Extraction Arm
HA-CMSC-G2-W-AEA
HA-SERIES-1219-CM
Replacement Filters
www.HealthyAir.com

2
WARNING
Cut power to the unit before servicing or replacing filters. Failure to
do so could result in serious personal injury and death.
I. Important Safety Instructions
Read the Owner's Manual and Important Safety Instructions carefully. Failure to
follow these instructions could cause a malfunction of the filter or unsatisfactory
performance. Follow a regular service and maintenance schedule for efficient
operation.
To reduce the risk of electric shock, fires, and/or injury:
• Do not use the air purifier in wet or damp locations
• Do not use outdoors
• Do not use at ambient temperature of above 95°F/35°C
• Do not use fabrics or other material to cover the inlet and outlet of the unit
• Do not allow children to operate or play with the unit
For safety reasons and to prevent electric shock, cut power to the unit under the
following conditions:
• When not in use for a long period of time
• When cleaning, servicing the machine or during replacement of filters
• When moving the air purifier
To prevent electric shock, do not dismantle, repair or modify this product.
Maintenance and cleaning instructions should be followed exactly as directed in
this manual. In case of malfunction, please contact an authorized distributor or
Healthy Air Inc. for service instructions.
To reduce the risk of electric shock, the unit has grounding type wiring that has a
third (grounding) wire. The unit must be hard wired, and all wiring must comply
with applicable electrical codes and ordinances. Do not alter the wiring.

3
II. Technical Specifications
Model Number
HA-CMSC-G2-AEA-W
Rated Voltage
120V/60HZ
Power Consumption
200W
Unit Weight
70 lbs.
Extraction Arm Weight
18 lbs.
Base Dimensions
24” (W) x 24” (L) x 15.4” (H)
Extraction Arm Dimensions
128” Extraction Arm (Fully Extended)
68” Vertical Section (Fixed)
63” Articulating Section (Adjustable)
Air Flow Rate
160 cfm
Sound Level
64 dB

4
III. Packaging Reference
The HealthyAir® Ceiling-Mount Aerosol Extractor, model HA-CMSC-G2-AE is
packaged in three (3) boxes as follows:
Note, in cases when multiple units are ordered, or customized orders are
placed, the secondary items may be packed in additional boxes.
Box 1:
(1) CMSC (Ceiling-Mount Source Capture) Unit
(1) Series-1219-CM Filter Set
(1) Inlet Port Cover-Plate
(2) Outside Vent Cover Plates
(1) Remote Control
(2) Batteries
(1) Manual Download Sheet

5
III. Packaging Reference
Box 2:
(1) Mounting Flange w/ 22” Pipe
(1) T-Outlet with 5” Pipe Stub
(1) 15” Pipe
(1) 3-Joint Articulating Extraction Arm Pipe
(1) Hood w/ Mounting Rings
(12) Screws
Box 3:
(1) Inlet Tube
(1) Flex Hose
(2) Hose Clamp

6
IV. Component Reference
CMSC Unit
12. Eyebolt
13. Capacitor
14. HV PCB
15. PCB Board
16. Wiring Box
17. Safety Switch
18. Fuse
19. Control Panel
20. Control Panel Display
21. Remote Control
22. Inlet Port Cover-Plate
23. Outlet Vent Cover-Plates
1. Thumb Screw
2. Faceplate
3. Pre-Filter
4. eGrid®
5. eHEPA® Filter
6. Activated Carbon Filter
7. Fan Coil
8. Blower/Motor
9. HV Contact Spring
10. Outside-Vent Outlet Port
11. Casing

7
IV. Component Reference
Articulating Extraction Arm
1. Mounting Base Flange w/ 22” Pipe
2. Airflow T-Outlet w/ 5” Pipe Stub
3. 15” Pipe Section
4. 3-Joint Articulating Arm
5. Hood
6. 360° Swivel Ring
7. Locking Knob
8. Airflow Control Valve
9. Handle
10. Flex Hose w/ (2) Hose Clamps

8
V. Installation Instructions
5.1 Install Eyebolts
5.1.1 Carefully place the CMSC unit face down, as shown in Fig. 1.
5.1.2 Screw the four (4) Eyebolts into the respective rivet nuts, located at the
four corners of the Casing.
5.1.3 Ensure that each Eyebolt is fully and securely installed.
Fig. (1) – Installing Eyebolts
Eyebolts
Faceplate
Casing
CMSC Unit

9
V. Installation Instructions
5.2 Locating Unit
For optimal performance, the HealthyAir® Ceiling-Mount Aerosol Extractor
should be located such that the Hood of the Extraction Arm can be strategically
positioned about 6”-12” from the emission source.
The unit base should also be installed where it can be easily accessed and
opened for periodic filter replacement. Refer to Section 9.2 for filter
replacement details.
5.2.1 The base unit is designed to be installed in place of a standard 2'x2’
ceiling tile, and it must be securely attached to the building structure for
adequate support.
5.2.2 Depending on the type of building structure, and whether the ceiling has
I-Beam or concrete construction, follow the appropriate protocol for
proper installation and support of the unit.
5.3 Locating Extraction Arm
The Articulating Extraction Arm is specifically designed to work with the
HealthyAirâ Ceiling-Mount Source Captureâ unit model HA-CMSC-G2.
Together, this system will enable effective capture and filtration of ultra-fine
airborne aerosols generated in various procedures.
The Articulating Extraction Arm is to be installed to the main structure in the
ceiling (above the drop ceilings) on either side of the chair or work area. The
exact and optimal location of the arm depends on the specific layout of the site
and the presence of other equipment.
In general, the Articulating Extraction Arm should be located within a radius of
36” from the area where work is performed. The arm is equipped with (3)
adjustable joints and a 360° swivel ring, that enable it to be maneuvered to
position the capture hood within 6” of the breathing zone.
The Ceiling-Mount Source Captureâ unit is to be located 4-6’ from the
Articulating Extraction Arm and connected to the arm via a Flex Hose.

10
V. Installation Instructions
5.4 Mount CMSC Unit to I-Beam Ceiling Structure
Fig. (2) – Mounting CMSC Unit to I-Beam Ceiling
5.5 Mount CMSC Unit to Concrete Ceiling Structure
Fig. (3) – Mounting CMSC Unit to Concrete Ceiling
I-Beam
12 Gauge
Wire Rope
M6 Nut
Concrete Ceiling
Expansion Tube
Suspended Ceiling
Eyebolt
Suspended Ceiling
M6 Nut
M6 Expansion
Screw & M6 Screw
CMSC Unit
CMSC Unit

11
V. Installation Instructions
5.6 Install Inlet Tube
The Faceplate of the CMSC unit has two (2) 4” Ø Inlet Ports. One of the Inlets
Ports is to be sealed with the Inlet Port Cover Plate, while the other is
uncovered.
Note that, either Inlet Port can be used depending on the preferred
arrangement. In some cases, both Inlet Tubes may be utilized for connection to
one Extraction Arm in order to boost the inlet airflow at the Hood.
5.6.1 Unscrew and remove the three (3) Thumb Screws that are mounted
around the uncovered 4” Ø Inlet Port on the Faceplate, as shown in
Fig. 4.
Fig. (4) – Faceplate with Inlet Ports
5.6.2 The flange of the Inlet Tube has a three-hole cutout pattern, as shown
in Fig. 5. Align the cutouts on the flange with the three (3) Screw and
Washers that are pre-installed around the Inlet Port. Then press the
Inlet Tube flush against the Faceplate and rotate the Inlet Tube
counterclockwise to lock it in place.
Thumb Screw
Inlet Port
Screw & Washer

12
V. Installation Instructions
5.6 Install Inlet Tube
5.6.3 Secure the Inlet Tube to the Faceplate by reinstalling and screwing in
the (3) Thumb Screws.
Note that, either Inlet Port can be used depending on the preferred
arrangement.
In some cases, both Inlet Tubes may be utilized for connection to one
Extraction Arm in order to boost the inlet airflow at the Hood.
Fig. (5) – Installing Inlet Tube on Faceplate
Inlet Tube
Thumb Screw

13
V. Installation Instructions
5.7 Install Articulating Extraction Arm
The Extraction Arm is designed to be independently anchored to the ceiling
and connected to the Inlet Tube of the CMSC unit via a flex hose. The length
of this connection tube can be increased or decreased, as needed, to best
locate the Articulating Extraction Arm.
5.7.1 Locate the Mounting Flange with 22” Pipe Section and fit the pipe end
into one end of the Airflow T-Outlet, as shown in Fig. 6
Note: To customize the overall length of the vertical section of the
Articulating Extraction Arm, the 22” Pipe Section may be cut to reduce
the length between the Mounting Flange and the Airflow T-Outlet.
5.7.2 Drill (3) four small holes, using a 3/16” size drill bit, 120º apart around
the circumference of the pipe, where the pipe sections overlap.
5.7.3 Secure the Mounting Flange Pipe Section to the Airflow T-Outlet using
three (3) screws provided.
Fig. (6) – Installing Airflow T-Outlet
Mounting Flange
Airflow T-Outlet
Screw
22” Pipe

14
V. Installation Instructions
5.7 Install Articulating Extraction Arm
5.7.4 Fit one end of the 15” Pipe Section into the other end of the Airflow T-
Outlet, and drill three (3) small holes, using a 3/16” size drill bit, 120º
apart around the circumference of the pipe, where the pipe sections
overlap.
Fig. (7) – Installing T-Section
5.7.5 Install the Mounting Flange onto the support structure in the main
ceiling by using three (3) 3/8Ӯ bolts. Prior to installation, ensure that
the 5” Pipe Stub on the Airflow T-Outlet is pointing towards the Inlet
Tube of the CMSC unit.
Fig. (8) – Installing Mounting Flange
15” Pipe
Airflow T-Outlet
Screw
5” Pipe Stub
Bolt Hole
Mounting
Flange

15
V. Installation Instructions
5.7 Install Articulating Extraction Arm
5.7.6 Connect one end of the Flex Hose to the Airflow T-Outlet, and secure the
connection by tightening the Hose Clamp, as shown in Fig. 9.
5.7.7 Connect the other end of the Flex Hose to the Inlet Tube, and secure the
connection by tightening the Hose Clamp, as shown in Fig. 9.
Note: It is recommended that the CMSC unit is mounted close to the
Articulating Extraction Arm, to enable a short piece of Flex Hose,
preferably not longer than a 4’, to be used for connection.
Fig. (9) – Installing Flex Hose
Flex Hose
Airflow
T-Outlet
Inlet Tube
Hose Clamp
Hose Clamp

16
V. Installation Instructions
5.7 Install Articulating Extraction Arm
5.7.8 Install the preassembled 3-Joint Articulating Arm, by fitting the aluminum
360° Swivel Ring onto the 15” Pipe section, as shown in Fig. 10.
5.7.9 Once in place, use the holes in the aluminum ring part as a guide to drill
(3) small holes in the pipe, using a 3/16Ӯ drill bit.
5.7.10 Screw in the (3) screws provided to secure the 360° Swivel Ring to the
15” Pipe, as shown in Fig. 10.
Fig. (10) – Installing 3-Joint Articulating Section
3-Joint
Articulating Arm
360° Swivel Ring
Screw

17
V. Installation Instructions
5.7 Install Articulating Extraction Arm
5.7.11 Install the Hood onto the end of the 3-Joint Articulating Arm by first
positioning the Hood in between the two (2) Retainer Collars, as
shown in Fig. 11.
Fig. (11) – Aligning Hood and Retainer Collars
5.7.12 Slide the Female Retainer Collar onto the end of the Articulating Arm
then insert the end of the Male Retainer Collar into the hole in the top
of the Hood, as shown in Fig. 12.
Fig. (12) – Installing Retainer Collars
Hood
Male Retainer Collar
Female Retainer Collar
3-Joint
Articulating Arm
Female Retainer Collar
Male Retainer Collar

18
V. Installation Instructions
5.7 Install Articulating Extraction Arm
5.7.13 Align the screw holes on the Male Retainer Collar with the screw
holes on the end of the Articulating Arm and insert (2) screws to
secure the Male Retainer Collar to the Articulating Arm, as shown in
Fig. 13.
Fig. (13) – Installing Retainer Collar on Articulating Arm
5.7.14 Secure the Hood assembly onto the Articulating Arm by screwing the
Female Retainer Collar onto the Male Retainer Collar, as shown in
Fig. 14.
Fig. (14) – Securing Hood Assembly
Screw
Retainer Collar

19
V. Installation Instructions
5.7 Install Articulating Extraction Arm
5.7.15 Mount the Handle to the pipe in between the third joint and the Hood.
5.7.16 Fix the position of the assembly, as needed, by rotating the arm via
the 360° Swivel Ring and adjusting the joints of the 3-Joint
Articulating Arm, shown in Fig. 15. Once in position secure the
assembly by tightening the Locking Knobs.
Note: An Airflow Control Valve is provided in the last section of the
extraction arm pipe. This will allow opening/shutting the air flow. It is
recommended that this valve is placed in the fully open position while
using the extraction arm.
Fig. (15) – Adjusting Articulating Extraction Arm
Locking Knob
360° Swivel Ring
Airflow Control Valve