Hearth and Home Technologies IntelliFire IFT-WFM User manual

1Hearth & Home Technologies • Wi-Fi Module Installation Instructions & User Guide • 2326-984 Rev. C • 7/20
Leave this manual with party responsible for use
and operation.
IntelliFire® Wi-Fi Module (IFT-WFM)
Installation Instructions
1. Introduction
The IntelliFire Wi-Fi Module (IFT-WFM) is designed to
allow the communication between the Hearth & Home
Technologies appliance and an Android or iOS device.
The IntelliFire app allows the ability to control many
of the available features on the appliance. Also the
IntelliFire skill on Amazon Alexa or Google Assistant
allows you to turn on and o󰀨 your appliance.
Note: The IntelliFire Wi-Fi module supports 2.4GHz or
2.4GHz / 5GHz dual band Wi-Fi networks only. To check
your network frequency, refer to your wireless router
manual or contact your internet service provider.
2. Wi-Fi Module (IFT-WFM) Installation
A. Precautions / Preparation
This device is tested and safe when installed in accor-
dance with this installation manual. Do not install any
components that may be damaged.
Do not modify, disassemble, or substitute any of the com-
ponents included with this kit. Installation of this kit must
be done by a qualied service technician.
For best performance, the location of the IntelliFire IFT-
WFM to the Wi-Fi router or your network extender should
be less than 50 feet from the appliance.
Hearth & Home Technologies disclaims any responsibility
for, and the warranty will be voided by, the following actions:
• Installation and use of any damaged system component.
• Modication of the system component.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a re hazard.
• Read, understand and follow these instructions for safe
installation and operation.
B. Kit Contents
• Wi-Fi Module (IFT-WFM)
C. Installation Steps
CAUTION! Do not install damaged components. If you
received components that are damaged, contact your
dealer for assistance.
1. Write the IFT-WFM Wi-Fi SSN# on top of the User
Guide. If you have multiple appliances to set up,
write the appliance description / location associated
with the IFT-WFM Wi-Fi SSN#. See Figure 1.
Figure 1 IFT-WFM Wi-Fi SSN # Location
IFT-WFM
Wi-Fi
SSN #
2. Locate the IntelliFire Touch electronic control module
(IFT-ECM) in the control cavity of the appliance and
move the selector switch to the OFF position. See
Figure 3.
NOTICE: IFT-ECM must have Wi-Fi sticker adhered to
it. If the IFT-ECM does not have the sticker, you must
replace it with one that does. See Figure 2.
Figure 2 Wi-Fi Label
Wi-Fi LABEL RUBBER COVER

Hearth & Home Technologies • Wi-Fi Module Installation Instructions & User Guide • 2326-984 Rev. C • 7/20 2
6. Once steps 2 thru 5 are complete, your IFT-ECM
/ IFT-WFM is ready to be set up with the IntelliFire
app.
4. Connect the IFT-WFM to the IFT-ECM by aligning the
pins and tabs and pushing the IFT-WFM into the IFT-
ECM until both tabs snap into position. Ensure the two
components are fastened securely to one another.
See Figure 3.
3. Locate the IFT-WFM port on the end of the IFT-ECM.
Remove and discard the rubber cover from the IFT-
WFM port. See Figure 2.
5. Move the selector switch on the IFT-ECM back to
‘Remote’ position. The IFT-ECM will beep and display
three green LED ashes. On the IFT-ECM, locate the
‘PILOT’ button then press and hold for ten seconds.
The IFT-ECM will emit one audible beep for four
seconds. Release the ‘PILOT’ button. The IFT-WFM
green LED will ash every two seconds, indicating it
has an open access point. You can conrm the open
access point by seeing the IntelliFire_XXXX network
in the available Wi-Fi networks on your smart device.
Note: The IFT-RFM is still required for use with a
remote to enable the thermostat function. The room
temperature is measured by a sensor in the IFT-
RC150 and/or IFT-RC400 remote control. Without a
paired remote, the TEMP function in the app will not
function correctly.
Figure 3 Connect Wi-Fi Module (IFT-WFM) to IFT-ECM
‘OFF’ POSITION‘OFF’ POSITION
PAIRING HOLE
IFT-WFM
IFT-ECM
(Wi-Fi MODULE)
IFT-RFM
IFT-WFM
LED
IFT-ACM
PILOT
Please contact your Hearth & Home Technologies
dealer with any questions or concerns.
For the location of your nearest
Hearth & Home Technologies dealer,
please visit www.hearthnhome.com.
Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
FCC Warning
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment o󰀨 and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit di󰀨erent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Canadian DOC Notice
This digital apparatus does not exceed the (Class A/ Class
B) limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian
Department of Communications.
Canadian IC Notice
This device complies with RSS-210 of Industry and Science
Canada. Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Caution: The Federal Communications Commission warns that
changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to op-
erate the equipment.
FCC Compliance Statement:
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, includ-
ing interference that may cause undesired operation of the
device.