Heat Controller Comfort-Aire CD-121 User manual

Window-Type
Air Conditioner
Service Manual
CAUTION
-Beforeservicingtheunit,readthe"safetyprecautions"inthismanual.
-Onlyforauthorizedservicepersonnel.
HEAT CONTROLLER, INC.
MODELS: CD-121
CD-101-5

2Room Air Conditioner
Air Conditioner Service Manual
TABLE OF CONTENTS
Safety Precautions..........................................................................................................................................3
Dimensions .....................................................................................................................................................5
Outside Dimensions...................................................................................................................................5
Product Specifications ..................................................................................................................................6
Installation.......................................................................................................................................................7
Select the Best Location ...........................................................................................................................7
How to Install..............................................................................................................................................7
Installation Kits Content(Some Models).....................................................................................................7
How to secure the Drain Pipe.....................................................................................................................9
Operation ......................................................................................................................................................10
Features...................................................................................................................................................10
Insulation Resistance Test........................................................................................................................10
About the Controls on the Air conditioner ................................................................................................10
Disassembly ..................................................................................................................................................11
Mechanical Parts......................................................................................................................................11
Air Handling Parts....................................................................................................................................12
Electrical Parts .........................................................................................................................................13
Refrigerating Cycle...................................................................................................................................14
Schematic Diagram.......................................................................................................................................17
Wiring Diagram.........................................................................................................................................17
Troubleshooting Guide.................................................................................................................................18
Piping System ..........................................................................................................................................18
Troubleshooting Guide .............................................................................................................................19
Room Air Conditioner Voltage Limits........................................................................................................21

Service Manual 3
Safety Precautions
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must
be followed.
■Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
■Meanings of symbols used in this manual are as shown below.
WARNING
CAUTION
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.
WARNING
■Installation
Be sure not to do.
Be sure to follow the instruction.
Always install the expansion panel(s).
• No installation may cause fire and electric shock acci-
dent.
Do not place the power cord near a heater.
• It may cause fire and electric shock.
Do not use the power cord near flammable gas or
combustibles such as gasoline, benzene, thinner,
etc.
• It may cause explosion or fire.
Do not disassemble or modify products.
• It may cause failure and electric shock.
Gasolin

4Room Air Conditioner
Safety Precautions
Never touch the metal parts of the unit when
removing the filter.
• They are sharp and may cause injury.
Do not block the inlet or outlet.
• It may cause failure of appliance or accident.
Ensure that the outer case is not damaged by age
or wear.
• If leaving appliance damaged, there is concern of
damage due to the falling of product.
Be cautious not to touch the sharp edges when
installing.
• It may cause injury.
Hold the plug by the head when taking it out.
• It may cause electric shock and damage.
Turn off the main power switch when not using it
for a long time.
• Prevent accidental startup and the possibility of injury.
■Installation

Dimensions
Dimensions
W
H
D
W mm(inch) 368(14 1/2")
H mm(inch) 521(20 1/2")
D mm(inch) 584(23)
Model
Dimension
All Model
Outside Dimensions
This symbol alerts you to the risk of electric shock.
This symbol alerts you to hazards that could cause harm to the
air conditioner.
This symbol indicates special notes.
NOTICE
Symbols Used in this Manual
Service Manual 5

6Room Air Conditioner
Product Specifications
Product Specifications
SPECIFICATIONS ARE SUBJECT TO MINOR CHANGE WITHOUT NOTICE FOR FURTHER
IMPROVEMENT.
NOTICE
CD-101-5 CD-121
1１,５00
1,２１0
11.０
655g(23.1oz)
3 ROW 16STACKS,
SLIT FAN TYPE
79/36
（inch）
（mm）
77/35
141/2×201/2×23
VERTICAL LOUVER （RIGHT&LEFT）
HORIZONTAL LOUVER （UP&DOWN）
OVERLOAD PROTECTOR
INTERNAL THERMAL PROTECTOR
3/3
6 POLES
368×521×５８４
POWER CORD
DRAIN PIPE SPLASHED BY FAN SLINGER
3 WIRE WITH GROUNDING
ATTACHMENT PLUG（CORD-CONNECTED TYPE）
OPERATING
CONDITION
PROTECTOR
OUTSIDE DIMENSION
（W×H×D）
COMPRESSOR
FAN MOTOR
INDOOR （℃）
10,000
1,050
9.6
AIR DIRECTION CONTROL
3 ROW 16STACKS, SLIT FAN TYPE
2 ROW 23STACKS,
LOUVER FIN TYPE
REMOTE CONTROLLER
THERMOSTATROOM TEMP . CONTROL
OUTDOOR （℃）
DRAIN SYSTEM
NET WEIGHT （lbs/kg）
CONSTRUCTION
FAN SPEEDS，FAN/COOLING
FAN MOTOR
OPERATION CONTROL
115V/60Hz
9.5
26.7(DB)* 19.4(WB)**
480g(16.9oz)
E.E.R (BTU/W·h)
REFRIGERANT（R-22）CHARGE
TURBO FAN
AXIAL FAN
EVAPORATOR
CONDENSER
FAN，INDOOR
FAN，OUTDOOR
35(DB)* 23.9(WB)**
POWER SUPPLY
COOLING CAPAC (Btu/H)
INPUT (W)
RUNNING CUR (A)
ITEMS
MODELS

1. These instructions are for a horizontal sliding or a
casement window.
2. The electrical outlet must be within reach of the
power cord.
For installation in a casement window, the window
frame assembly and the side of the building must be
adequate to support the weight of the air conditioner.
Service Manual 7
Installation
Installation
Installation Kits Contents
Window Requirements
8
7
9 10
3
12
11
16 17
1
6
13
15
4
14
2
5
21" min.
40 1/2" max.
15 1/2"
min.
21 1/2" min.
15 1/2" min.
16 1/2" max.
Horizontal sliding window Casement window
NO. NAME OF PARTS QTY
1 Curtain 1
2 Curtain Frame 1
3 Upper Guide 1
4 Side Guide 2
5 Support Bracket 1
6 Bracket 1
7 Leveling Bolt & Nut 1
8 Bolt 2
9 Nut 2
10 Washer 2
11 Side Guide seal 1
12 Foam Seal Strip 1
13 Window Track Seal 1
14 Window Locking Bracket 1
15 Screw (Type A) 9
16 Screw (Type B) 3
17 Screw (Type C) 8

8Room Air Conditioner
Installation
How to Install the Unit
1. To prevent vibration and noise, make sure the unit is
installed securely and firmly
2. Install the unit where the sunlight does not shine
directly on the unit.
3. The outside of the cabinet must extend outward for at
least 14" and there should be no obstacles, such as a
fence or wall, within 20" from the back of the cabinet
because it will prevent heat radiation of the condenser.
Restriction of outside air will greatly reduce the cooling
efficiency of the air conditioner.
All side louvers of the cabinet must remain
exposed to the outside of the structure.
4. Install the unit at a slight incline so the back is slightly
lower than the front(about 1/4").
This will force condensed water to flow to the outside.
5. Install the unit with the bottom about 30"~60" above
the floor level.
NOTICE
About 1/4"
30"~60"
Awning
Cooled air
Fence
Over 20"
Heat
radiation

Service Manual 9
Installation
Horizontal Sliding Window Installation
1. Loosely attach the Support Bracket to the bottom of
Bracket using Bolts, Washer, and Nuts. Attach the
Leveling Bolt and Nut. (Fig. 1)
2. Remove protective backing from Window Track Seal
and apply seal to window track. (Fig.2)
3. Measure and lightly mark a line 8-1/4 inches from
window jamb. Center the Support Bracket assembly
on the window track and fasten with 4 Type C
screws.(Fig. 2)
4. Put the Support Bracket against the outside wall and
tighten the Bolts on top of the Bracket. Adjust the
Leveling Bolt so that the air conditioner will be
installed with a very slight tilt (about 1/4") downward
toward the outside for proper drainage.
Tighten the nut. (Fig. 3)
DO NOT drill a hole in the bottom of the base
pan. The air conditioner is designed to oper-
ate with the bottom of the base pan approxi-
mately half-full of water.
5. Fasten Side Guides to the sides of the Air
Conditioner using 3 Type A screws per Guide. Start
with first screw at middle of Guide.
(Fig. 4)
6. Fasten Upper Guide on the top of the Air Conditioner
using 3 Type A screws. (Fig. 4)
NOTICE
81/4inchesinches81/4inches
WindoWindow JambambWindow Jamb
WindoWindow TrackWindow Track
WindoWindow Track
Seal
Window Track
Seal
Bracket
Support Bracket
Nut
Washer
Leveling Bolt & Nut
Bolt
Type C screwType C screw
About
1
/ 4 "
Outside Wall
Fastening Side Guides
Upper Guide
Side Guide
Fig. 1
Fig. 2
Fig. 3
Fig. 4

10 Room Air Conditioner
7. Measure height of window opening from top of
Bracket assembly as shown Fig. 5. Subtract 20-3/4
inches. Mark this measurement on Curtain and cut
the Curtain. (Fig. 5)
8. Slide Curtain into Curtain Frame. Slide Curtain
Frame assembly into side Guides of the Air
Conditioner cabinet. Make sure Curtain is firmly
enclosed on all sides by the Frame. (Fig. 6)
9. Cut side Guide seal into 2 equal lengths. Remove
protective backing and apply it to the rear side of cab-
inet Side Guides, starting just below Curtain Frame
assembly. Pinch off excess length so seal is even
with the bottom of side Guide. (Fig. 7)
10. Place Air Conditioner in window opening. It should
sit on Bracket assembly so that Curtain Frame and
cabinet Side Guides are against top and side win-
dow jambs. Mate front of Bracket with Base Guide
attached to the bottom of base pan.
11. Drill 1/8 inch holes in window track through the
existing holes on Base Guide. Screw 4 Type C
screws through the holes. (Fig. 8)
12. If this is a casement window installation, proceed to
Casement Window Installation. If not, slide inner
window sash firmly against side of the cabinet.
13. Drill 1/8 inch hole in window jamb to align with the
existing holes in the Curtain Frame. Attach Curtain
Frame to window frame with 2 Type B screws. (Fig.
8)
Frame Curtain
Curtain
Apply weather seal
to side guides
just below edge of
Curtain Frame .
Type B screwType B screw
Base panBase pan
BracketBracket
Window Track
Base GuideBase Guide
Type C screw Window Track
Fig. 5
Fig. 6
Fig. 7
Fig. 8

Check all seals and plug any remaining air
gaps with a suitable weatherproof caulk.
14. If this is a casement window installation, proceed
to Casement Window Installation.
If not, stuff the Foam Seal Strip between the verti-
cal sash and the window glass. (Fig. 9)
15. Attach the L Bracket with a Type B screw. (Fig. 9)
NOTICE
Service Manual 11
Foam seal strip
Window
locking
bracket
Casement Window Installation
Fig. 9
1. Installation procedure is the same as that described in steps 1 through 11 and step 13 of the Horizontal
Sliding Window installation.
2. If the window opening is wider than 15-3/4 inches you will need to install a filler panel. Make this panel from
3/4 inch thick wood and run it the full length of the window.
Attach it securely to the window frame and paint it to protect it from the weather.
3. Since styles and sizes of casement windows vary widely, it is advisable to have the air conditioner installed by
someone skilled in this type of installation.

12 Room Air Conditioner
Operation
Controls
Remote Control Operations
Operation
The remote control and control panel will look like those represented in the following pictures.
Power
Temp
Fan Speed
Timer Mode
1
1
2
4
3
2
3
45
5
6
1. POWER
•To turn the air conditioner ON, push this button. To turn
the air conditioner OFF, push the button again.
•This button takes priority over any other button.
•When you first turn it on, the unit is in cool mode, high fan
speed, temperature setting at 72˚F.
2. TEMPERATURE SETTING
•Use this button to automatically control the temperature
of the room.
The temperature can be set within a range of 60°F to
86°F by increments of 1°F.
3. MODE
- Every time you push this button, it will cycle through the
following modes: COOL, ENERGY SAVER and FAN.
- ENERGY SAVER
•The fan stops when the compressor stops cooling.
Approximately every 3 minutes the fan will turn on and
the unit will check the room air to determine if cooling is
needed.
4. FAN SPEED
•Every time you push this button, it advances the setting
as follows: {High(F3) →Low(F1) →Med(F2) →High(F3)}
5. TIMER
- SHUT-OFF TIME
•You will usually use shut-off time while you sleep.
•With unit running, use Timer to set number of hours until
shut-off.
•For your sleeping comfort, once Time is set, the
Temperature setting will raise 2°F after 30 min, and 2°F
after another 30 min.
•Every time you push Timer button, it advances the Timer
setting as follows: 1 Hour →2 Hours →etc. → 12 Hours
maximum.
- START TIME
•With unit not running, use timer to set number of hours
before unit starts.
•Every time you push Timer button, it advances the Timer
setting as follows: 1 Hour →2 Hours →etc. →12 Hours
maximum.
6. REMOTE CONTROL SENSOR
AUTO RESTART
When power is restored after an electrical power failure, the unit will begin to run at its last setting.

Service Manual 13
Disassembly
Mechanical Parts
Disassembly
1. Front Grille
1. Open the inlet grille downward and remove
the air filter.
2. Remove the screws which fasten the front
grille.(See Figure 1)
3. Pull the front grille from the right side.
4. Remove the front grille.(There are 4 hooks.)
5. Re-install the components by referring to the
removal procedure, above.
2. Cabinet
1. After disassembling the FRONT GRILLE,
remove the 6 screws which fasten the cabi-
net at both sides.(See Figure 2)
2. Remove the 4 screws which fasten the cabi-
net at back.
3. Remove the cabinet.
4. Re-install the components by referring to the
removal procedure, above.
3. Control Box
1. Remove the front grille. (Refer to section 1)
2. Remove the cabinet. (Refer to section 2)
3. Remove the 1 screw which fasten the
power cord. (See Figure 3)
4. Disconnect the grounding screw from the
evaporator channel.
5. Remove the 2 screws which fasten the con-
trol box.(See Figure 3)
6. Remove the housing which connects motor
wire in the control box.
7. Remove three leads which connect com-
pressor.
8. Discharge the capacitor by placing a 20,000
ohm resistor across the capacitor terminals.
9. Raise the control box upward completely.
10. Re-install the components by referring to
the removal procedure, above.
(Refer to the circuit diagram found on pages
21~22 in this manual and on the control
box.)
- Before the following disassembly, set POWER SWITCH to OFF and disconnect the power cord.
D
Figure 1
Figure 3
Figure 2

4. Air Guide and Turbo Fan
1. Remove the front grille. (Refer to section 1)
2. Remove the cabinet. (Refer to section 2)
3. Remove the control box. (Refer to section 3)
4. Remove the 4 screws which fasten the brace.
5. Remove the brace.
6. Remove the 2 screws which fasten the upper air guide.
(See Figure 4)
7. Remove the upper air guide.
8. Remove the 2 screws which fasten the evaporator.
9. Move the evaporator forward and pulling it upward slight-
ly. (See Figure 5)
10. Remove orifice by pulling two taps.
11. Remove the clamp with a hand plier which secures the
turbo fan.
12. Remove the turbo fan. (See Figure 6)
13. Remove the motor. (Refer to section 11)
14. Remove the 2 screws which fasten the lower air guide
from the base pan.
15. Remove the 2 screws which fasten the motor mount
from the base pan.
16. Remove the 2 screws which fasten the lower air guide
and motor mount.
17. Move the lower air guide backward and pull out from
the base pan. (Move the lower air giude carefully.)
18. Re-install the components by referring to the removal
procedure, above.
5. FAN
1. Remove the cabinet. (Refer to section 2)
2. Remove the brace (Refer to section 4)
3. Remove 6 screws which fasten the condenser.
4. Move the condenser to the right carefully.
5. Remove the clamp with a hand plier which secures the fan.
6. Remove the fan. (See Figure 7)
7. Re-install by referring to the removal procedure.
14 Room Air Conditioner
Disassembly
Air Handling Parts
Figure 4
Figure 5
Figure 6

5. Shroud
1. Remove the fan. (Refer to section 2.5)
2. Remove the shroud. (See Figure 8)
3. Re-install the components by referring to the
removal procedure, above.
6. Overload Protector
1. Remove the cabinet. (Refer to section 2)
2. Remove the nut which fastens the terminal cover.
3. Remove the terminal cover. (See Figure 9)
4. Remove all the leads from the overload protector.
5. Remove the overload protector.
6. Re-install the components by referring to the
removal procedure, above.
7. Compressor
1. Remove the cabinet. (Refer to section 2)
2. Discharge the refrigerant system using a FreonTM
Recovery System.
If there is no valve to attach the recovery system,
install one (such as a WATCO A-1) before venting
the FreonTM. Leave the valve in place after
servicing the system.
3. Remove the overload protector. (Refer to section 6)
4. After purging the unit completely, unbraze the suc-
tion and discharge tubes at the compressor con-
nections.
5. Remove the 3 nuts and the 3 washers which
fasten the compressor.
6. Remove the compressor. (See Figure 10)
7. Re-install the components by referring to the
removal procedure, above.
Service Manual 15
Disassembly
Electrical Parts Figure 8
Figure 9
Figure 10

16 Room Air Conditioner
Disassembly
8. Capacitor
1. Remove the cabinet. (Refer to section 2)
2. Remove the screw and the clamp which fastens the
capacitor.
3. Disconnect all the leads of capacitor terminals.
4. Re-install the components by referring to the
removal procedure, above. (See Figure 11)
9. Power Cord
1. Remove the cabinet. (Refer to section 2)
2. Disconnect the grounding screw from the control
box.
3. Disconnect the 2 receptacles.
4. Remove a screw which fastens the clip cord.
(See Figure 12)
5. Remove the power cord.
6. Re-install the component by referring to the above
removal procedure, above.
(Use only one ground-marked hole for ground
connection.)
7. If the supply cord of this appliance is damaged, it
must be replaced by the special cord. (The
special cord means the cord which has the same
specification marked on the supply cord attached at
the unit.)
10. Thermostat
1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the 2 screws which fasten the thermostat.
3. Disconnect 2 leads of thermostat terminals.
4. Remove the thermostat.
5. Re-install the components by refering to the above
removal procedure. (See Figure 13)
Figure 11
Figure 12
Figure 13

Service Manual 17
Disassembly
Refrigerating Cycle
11. Motor
1. Remove the cabinet. (Refer to section 5)
2. Remove the turbo fan. (Refer to section 5)
3. Remove the fan. (Refer to section 6)
4. Remove the 4 screws which fasten the motor from
the Motor Mount. (See Figure 14)
5. Remove the motor.
6. Re-install the components by referring to the
removal procedure, above.(See Figure 14)
12. CONDENSER
1. Remove the cabinet. (Refer to section )
2. Remove the 4 screws which fasten the brace.
3. Remove the 4 screws which fasten the condenser
and shroud. (See Figure 15)
4. Remove the 2 screws which fasten the condenser
and base pan.
5. After discharging the refrigerant completely,
unbraze the interconnecting tube at the condenser
connections.
6. Remove the condenser.
7. Re-install the components by referring to notes.
(See Figure 15)
13. Evaporator
1. Remove the cabinet. (Refer to section 2)
2. Remove the control box.(Refer to section 3)
3. Remove the upper air guide. (Refer to section 4)
4. Remove the 2 screws which fasten the evaporator
from lower air guide.
5. Move the evaporator sideways carefully.
(Refer to section 4)
6. After discharging the refrigerant completely,
unbraze the interconnecting tube at the evaporator
connections.
7. Remove the evaporator.
8. Re-install the components by referring to notes.
(See Figure 16)
Figure 14
Figure 15
Figure 16
Discharge the refrigerant system using a
FreonTM Recovery System.
If there is no valve to attach the recovery
system, install one (such as a WATCO A-1)
before venting the FreonTM. Leave the valve in
place after servicing the system.
CAUTION

18 Room Air Conditioner
—Replacement of the refrigerant.
1. When replacing the refrigerant, be sure to
Discharge the refrigerant system using a FreonTM
recovery System.
If there is no valve to attach the recovery system,
install one (such as a WATCO A-1) before venting
the FreonTM. Leave the valve in place after
servicing the system.
2. After discharging the unit completely, remove the
desired component, and unbraze the pinch-off
tubes.
3. Solder service valves into the pinch-off tube ports,
leaving the valves open.
4. Solder the pinch-off tubes with Service valves.
5. Evacuate as follows.
1) Connect the vacuum pump, as illustrated figure
17A.
2) Start the vacuum pump, slowly open manifold
valves A and B with two full turns counterclock-
wise and leave the valves open.
The vacuum pump is now pulling through valves
A and B up to valve C by means of the manifold
and entire system.
3) Operate the vacuum pump for 20 to 30 minutes,
until 600 microns of vaccum is obtained. Close
valves A and B, and observe vacuum gauge for
a few minutes. A rise in pressure would
indicate a possible leak or moisture remaining in
the system. With valves A and B closed, stop
the vacuum pump.
4) Remove the hose from the vacuum pump and
place it on the charging cylinder. See figure 17B.
Open valve C.
Discharge the line at the manifold connection.
5) The system is now ready for final charging.
6. Recharge as follows :
1) Refrigeration cycle systems are charged from the
High-side. If the total charge cannot be put
in the High-side, the balance will be put in the
suction line through the access valve which you
installed as the system was opened.
2) Connect the charging cylinder as shown in figure
17B.
With valve C open, discharge the hose at the
manifold connection.
3) Open valve A and allow the proper charge to
enter the system. Valve B is still closed.
4) If more charge is required, the high-side will not
take it. Close valve A.
5) With the unit running, open valve B and add the
balance of the charge.
a. Do not add the liquid refrigerant to the Low-
side.
b. Watch the Low-side gauge; allow pressure to
rise to 30 lbs.
c. Turn off valve B and allow pressure to drop.
d. Repeat steps b. and c. until the balance of the
charge is in the system.
6) When satisfied the unit is operating correctly,
use the pinch-off tool with the unit still running
and clamp on to the pinch-off tube. Using a tube
cutter, cut the pinch-off tube about 2 inches from
the pinch-off tool. Use sil-fos solder and solder
pinch-off tube closed. Turn off the unit, allow it to
set for a while, and then test the leakage of the
pinch-off connection.
NOTES
If high vacuum equipment is used, adjust valves
A and B so they are opened only slightly for a few
minutes, then open slowly with the two full turns
counterclockwise. This will keep oil from foaming
and being drawn into the vacuum pump.
14. Capillary Tube
1. Remove the cabinet. (Refer to section 2)
2. After discharging the refrigerant completely,
unbraze the interconnecting tube at the capillary
tube.(See caution above)
3. Remove the capillary tube.
4. Re-install the components by referring to notes.
CAUTION

Service Manual 19
Disassembly
Equipment needed: Vacuum pump, Charging cylinder, Manifold gauge, Brazing equipment. Pin-off tool capable
of making a vapor-proof seal, Leak detector, Tubing cutter, Hand Tools to remove components, Service valve.
A
COMPOUND GAUGE
EVAPORATOR
(LOW PRESSURE SIDE)
COMPRESSOR
CAPILLARY TUBE
CONDENSER
(HIGH PRESSURE SIDE)
SEE INSETS
BELOW
MANIFOLD
GAUGE
B
A
B
EXTERNAL
VACUUM PUMP
A
CHARGING
CYLINDER
LOW HI
B
C
Figure 17A-Pulling Vacuum Figure 17B-Charging

Schematic Diagram
Wiring Diagram
20 Room Air Conditioner
1-5 1-5
C03D
16V
1000
CAPACITOR
MAINPOWER
RY-HI
RY-MED
RY-LOW
0.1/275V
14D561 14D271
ZNR01J
1201/2W
COMP
HERM
250V/T2A
RY-COMP
G4A-1A-E-LG
4 3
FUSE
1 3 5 7
9 1
3
CN-PWR
YW396-03AV
C
FAN
1
3
FAN
MOTOR
5 7
9
1 3
C01J
R01J
1N4004
D02D~D05D
POWERTRANS
1
2D02D
4D03D
7
50V
35V
+
D05D
D04D
C01D
1000
IIC01D
C02D
0.1
7812
LEDTYPE 88SEGMENT TYPE DISPLAY
4WAY
R03H
RY-4WAY
3
1
YW396-03AV
CN-MOTOR CN-4WAY
YW396-09AV
S/V-
1
3
optionalpart
PIPE-TH
12V
CoolOnly HeatPump
Model
CN-TH2
SMW250-04
RY-4WAY
X O
15
RY-MED RY-HI
IC01M
ULN2004AF
16 1
2
RY-COMP RY-4WAY RY-SYNC RY-LOW
CN-4WAY
O X
R03H
X O
10K
X
CN-TH2
O
13 12 14
12V 9
10 11 6
4 5 3 8 7
R21H
OR01H
5V
12.1K
1%
ROOM-TH
3
3
3
3
1
1
1
1
CN-TH1
SMW250-04
5V
1%
6.2K
R02H
SW6
D06F
SW4
D04FD05F SW5SW7
D07F
GND C22L
2-1 2-4 2-2 2-3 1-9 1-7 1-8 1-13 1-6
0.01
C06D
50V
50V
7805
IC02D
C04D
I
O
+
0.01
12V
O
C05D
220
10V
+
5V
5V
X O
J01F
1K
R01E
R01L
C01L
680pF
1K
R12F
20K
J01F
ULN2004AF
IC01G
8 9 CN-MAIN2
R01F
C01F
0.001 10K
14
3
R04G R06G R07G R05G
6 7
11 10
4 5
13 12
150 150 150 150
R02G R01G R03G
1 2
16 15
150 150 150
CN-DISP2
c
1-9 2-2 2-3 2-4 2-1
f
g
d e
1-8 1-7 1-13 1-6 a
b
RECEIVER BZ01E
PKM13EPY
-4000-A0
220
10V
0.4inch 88SEGMENT
3
9
8
6
7
1
c
DRY/HEAT
FAN
E/SAVER
TIMER
f
g
d e
COOL
a b
c
e
4
d
g
e
d
g
f
a
b
Digit1 10
a
f
Digit0 5
AutoRestart
1-10 1-11
NonAuto Restart
1-12
EEPROM(optionalpart)
8 9
10 11
7 5 6 1 2 3 4
TMP87CH47U
ION
36
R02E 20
LEDout2
LEDout1
LEDout0
MED
Buzzer
Receiver
LEDout3
31 32 33
34 35
28 29 30
HI
SEG-g
KEY0
KEY1
VDD
SLIDESW
SEG-e
SEG-f
SEG-d
3837 4039 4241 43 44
20
Option1
Option2
PipeTH
COMP
4WAY
SYNC
LOW
HVB
24 25 26 27 23
22 21
OR02H
1%
R22H
12.1K
TEST
VAref
VSS
Oscin
Oscout
/Reset
RoomTH
MICOM
1819 1617 1415
Tx
13 12
5V
Digit2(Scan2)
R02F
0.001
C02F 10K
Digit0(Scan0)
Digit1(Scan1)
SEG-c SEG-b
SEG-a
CN-MAIN1
Digit4(Scan4)
Digit3(Scan3)
SCL
SDA
Rx
Vcc
24LC01BT
SCL
SDA
WP
3A2
4GND
2 1A0
A1 6
5 7 8
C01P
0.01
1K
R04P
5V
R02P
20K R03P
20K
1K
0.01
C01A
12.1K
R01H
1%
OSC01B
8.00MG
R01B
1M R01A IC01A
S7136
5V
R03A
C02A
10uF 50V
+
100 3.6V
1
2
3
4.7K
R02A
Model
Q04G
A101S
TEMPUP
CN-DISP1
1-10 1-11 1-12 Vout +
Vcc 5V
5V 5V
1-1 1-1
TEMPDOWN
TIMER
D02F SW2 D01F
MODE
FAN
SW1
POWER
1-2 1-2
1-3 1-3
Q03G
A101S
1-4 1-4
A101S
Q02G
Q01G
A101S
EEPROM
O X
R04P
X O
c
b
5V