HEAT GLO FS-3-BK User manual

1Heat & Glo • FS-3-BK, FS-5-BK, FS-7-BK, FS-7BV-BK, FS-9-BK, FS-7-BK-AU Decorative Front Instructions • 2372-931 Rev. E • 6/21
Firescreen Decorative Front
Models: FS-3-BK, FS-5-BK, FS-7-BK, FS-7BV-BK, FS-9-BK, FS-7-BK-AU
- Installation Instructions -
Figure 1. Shoulder Bolt Locations
1. Remove all materials from the packaging.
2. Install the black shoulder bolts into the threaded inserts
located in the replace surround. See Figure 1. Install
four shoulder bolts on FS-3, FS-5, FS-7, FS-7BV and
FS-9 appliances. Install two shoulder bolts on FS-7-
BK-AU front only. Do not install lower shoulder bolts
for this front. The FS-7-BK-AU front uses seperate
magnet brackets on the bottom that are included with
the appliance.
Leave this manual with party responsible for use
and operation.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
CAUTION! Do not install damaged components.
WARNING! Risk of Fire! Combustible materials MUST
NOT overlap or be placed behind a decorative front.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and must be installed for
the protection of children and other at-risk
individuals.
Note: For use with the Fusion (SL-5F, SL-7F) models,
discard hood included with the FS-5-BK and FS-7-BK
and use the hood that originally shipped with the appli-
ance. Hood clips are already installed on the appliance.
3. Verify that the glass assembly is centered (left to right)
within the replace opening.
4. Remove the two screws that fasten the hood to the
side columns of the rescreen decorative front. Set the
hood in a safe place where it will not be damaged while
the decorative front is being installed on the appliance.

2Heat & Glo • FS-3-BK, FS-5-BK, FS-7-BK, FS-7BV-BK, FS-9-BK, FS-7-BK-AU Decorative Front Instructions • 2372-931 Rev. E • 6/21
Please contact your Heat & Glo dealer with any
questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
Cleaning Instructions for Decorative Fronts
Use a microber cloth and Windex® Original Glass
Cleaner or 03M003 Stove Bright® Glass Cleaner to
clean the decorative front immediately after installation
to remove acids deposited by the installer or technician.
Spray the cleaner onto the microber cloth and carefully
wipe the entire surface. The decorative front should
be cleaned in this manner annually by the homeowner
to remove ngerprints or other contaminants. Once
oxidation of the paint pigment has occurred, cleaning will
not restore the original color.
Figure 2. Firescreen Decorative Front
FS-3, FS-5, FS-7, FS-7BV, FS-9 ONLY
5. Align the bottom slots on the decorative front with the
bottom shoulder bolts and set the front onto the bottom
shoulder bolts. Tilt the decorative front towards the re-
place until it contacts the top shoulder bolts. Once the
decorative front contacts the top shoulder bolts, lift up
slightly and push decorative front toward replace until
slots and bolts are engaged. Release the decorative
front. The decorative front now hangs on the top two
shoulder bolts.
FS-7-BK-AU ONLY
Hang decorative front from top slots on upper mounted
shoulder bolts. Swing front down until it contacts mag-
nets installed on appliance.
6. Ensure the decorative front is properly attached and
securely positioned on the appliance.
7. Install the hood by inserting the oval holes on the hood
into the hood clips inside the appliance near the top.
Push the hood into the clips until it can go no further.
See Figure 3. See the properly installed hood in Figure 4.
TOP SLOT
(BOTH SIDES)
BOTTOM SLOT
(BOTH SIDES)
Figure 3. Install Hood
Figure 4. Hood Installed
HOOD INSTALLED
Note: Appearance of hood
may vary between models.
SERVICE PARTS LIST
Front Description Part Number
FS-3-BK Square Hood 2370-274
FS-5-BK Square Hood 2371-274
FS-7-BK Square Hood 2372-274
FS-7BV-BK Square Hood 2372-274
FS-9-BK Square Hood 2373-274