V-TAC 11109 User manual

Instruction Manual
Indoor P3 LED Display Screen
SKU Code: 11109 Watts: 400W/cabinet
Applications:
Applied to indoor places such as station,port,airport,shopping mall,hotel,meeting room,Stage Etc.
Specifications:
1
2
3
4
5
6
7
8
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14 Control system
How to installation:
1.For fixed the screen,first make a stable steel structure.(backside of the cabinet need to have protection)
2.Lock the cabinet backside door,if you want open the door,turn the door key direcetly.
3.Connect each cabinet,use hand connect the side lock,one by one.
LED Module Parameter
Pixel pitch
3mm
LED specification
SMD2121
LED configuration
SMD 3 in 1
Module size
192*192mm
Module resolution
64*64=4096dot
Drive Method
1/16 scan constant current
Drive IC
FM6124
power consumption
25-30W
LED Cabinet Parameter
Cabinet size(L*H*D)
576*576*85mm
Cabinet resolution
192*192
Module quantity each cabinet
3*3=9
power consumption
400w/cabinet
Cabinet material
Aluminum
Cabinet weight
10kg/cabinet
Screen Parameter
Pixel density
111111dots/sqm
Brightness
1000nits
Optimum view distance
more than 3m
gray scale
16bits
Display color
281 trillions(synchronized)
Operation power
AC 220V-240V/ 50/60Hz
power consumption
400W/cabinet
Control Mode
Synchronized
Refresh Frequency
800HZ
Surport signal input
S-Video,RGBHV,YUV etc.
PCTV nonlinearity card，DVI display card
Linsn control system
Control Distance
UTP140M,SINGLE MODE FIBER 15KM
Life span(50% brightness)
100000hrs
IP(Front)
IP40

4.Ensure all cabinets are locked properly.
6.Connect the main power cable from power box to screen,and main signal cable from PC to screen.
7.Ensure power&signal cable connected,then turn on power.
8. Insert sending card in CPU at first and please install software in computer , to connect software set up with screen
9. If you use notebook control,put the sending card to sending box,then use the HDMI-DVI cable connect
the sending box with the notebook.
Safety Warning
Please be sure to read this section of the security measures before installation,power supply,
operating and adjusting product!
This product is intended for professional use only!
Due to fire, electric shock and drop, the products will result in severe injury or even death
Warning ! Please be careful as the cabinet is heavy! Avoid finger injuries.
Warning! Be careful of shock
Close the general gates when the power cabling and wiring.
Close the gates before disconnecting and connecting any part of the unit cabinet.
Keep good grounding of the product.
The installation location of total power switch should be close to the product and in a obvious, easy place reach
cause we can disconnect the power in time when some error appears.
When finished the display assembling ,please carefully check if power wiring is in good condition.
Warning ! Be careful
The installation location of displays need good ventilation. Do not hang anything on the display.
Warning! Wearing a crash helmet, so as to avoid personal injury.
Please attention to the visual distance and avoid prolonged closely watching the screen,so as not to affect vision
Instructions
1.Each cabinet equipped with a synchronous receive card.
2.In the height direction,maximum connecting cabinet is 12 unit ones
3.Signal between cabinets use the up and down or left and right, the default cascading is the up and down connection.
5.Connect each cabinet,use screws connect steel connector with steel structure.
And then connect the signal&power cable(in and out) from cabinet to cabinet.

4.AC power cables between the cabinet to the cabinet and down cascade.
5.Each AC power cable leads from the distribution cabinet can cascade 12 unit cabinets at most.
6.The power consumption of every sqm is 1000W
7.This kind of LED display for indoor use only.
8.One sending card can support 1024(W)*768(H) dot screen area.
9. Accessories packed in separate carton.
System configuration
The whole system aremade up by the following points
series cabinet- Distribution Cabinet- Controlling computer-

5.Connect each cabinet,use screws connect steel connector with steel structure.
And then connect the signal&power cable(in and out) from cabinet to cabinet.