Heath Zenith Motion sensing Pendant Light 4350 User manual

FEATURES
• Light comes on when motion is detected.
• Automatically turns light off.
• Optional half power accent lighting.
• Photocell keeps the light off during daylight
hours.
• Hinged door for easy bulb access.
1 - Canopy Screws (x3)
2 - Universal Mounting Bracket
3 - Mounting Bracket Screws
(x2)
4 - Nut
5 - Star Washer
6 - S-Hanger Terminal
7 - Flat Washer
8 - Canopy
Model 4350
© 2007 HeathCo LLC 598-1219-05
DUAL BRITE
®
ON-TIME
TEST 1 510 MIN
OFF 3 6DUSK
TO DAWN
Junction Box
(Not Included)
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
9 - Knurled Canopy Nuts (x3)
10 - Decorative Flat Washer
11 - Small, Thick, Decorative
Washer
12 - 1" (25.4 mm) Threaded
Rod
13 - Mounting Rods (x3)
- 6" (15.2 cm) Rod
- 12" (30.5 cm) Rod (x2)
14 - Pendant Light Fixture
15 - Sensor Cover
16 - Smooth Sensor Cover
Screws (x4)
Other Items Not Shown:
- Wire Nuts (x3)
- Lens Shield (x2)
- S-Hanger
- Foam Tape
Be sure to remove all contents from packaging and verify all items are present before assembling this
light xture. This package includes the following items:
Meets the ENERGY STAR®guide-
lines when DualBrite®function
is off.
Motion Sensing Pendant Light

2598-1219-05
MANUAL MODE
AUTO
TEST
ON-TIME
TEST 1 5 10 MIN
TEST
Set ON-TIME switch to
1, 5, or 10 minutes.
AUTO
ON-TIME Switch at 1, 5, or
10 minutes
... back on.
1 Second OFF
then...
Manual mode only works at
nightbecausedaylightreturns
the sensor to AUTO.
Flip the light switch off for
one second then back on to
toggle between AUTO and
MANUAL MODE.
Manualmode worksonly with
the ON-TIME switch in the 1,
5, or 10 position.
MODE SWITCHING SUMMARY
Flip light switch off
for one second then
back on*
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
MANUAL MODE
ON-TIME
TEST 1 5 10 MIN
Set the ON-TIME switch
on the sensor to TEST.
REQUIREMENTS
• The light control requires 120 volts AC.
• If you want to use Manual Mode, the control must
be wired through a switch.
• Some electrical codes require installation by
a qualied electrician.
OPERATION
Note: When rst turned on wait about 1 1/2minutes
for the circuitry to calibrate.
* resets to Auto Mode at dawn.
Beforeinstallation,recordthe modelnumber
listed inside the xture. Attach receipt in case
of possible warranty issues.
Model Number:
Mode: On-Time Works: Day Night
Test 5 Seconds x x
Auto 1, 5, or 10 Min x
Manual To Dawn* x
Accent Off, 3, 6 Hr,
to Dawn
x
DualBrite®DIMMER CONTROL
Light comes on half bright for selected time after
dusk (Off, 3 hr., 6 hr., until dawn). Selecting OFF
disables this feature. The motion sensing features
will continue to work as described in this manual.
If motion is sensed, the light turns on full bright for
the ON-TIME (1, 5, or 10 minutes) then returns
to dim mode.

3
598-1219-05
INSTALL UNIVERSAL MOUNTING
BRACKET
Canopy Screw (x3)
(Tightened Finger
Tight)
Junction Box
Universal Mounting
Bracket
Mounting Bracket
Screw (x2)
ASSEMBLE CANOPY
1. Determinethenumberofmountingrodsneeded
to mount the pendant light.Any combination of
the 3 mounting rods may be used. Note: For
best performance, mount the xture so that the
sensor is between 8 and 10 feet (2.4 m) above
the ground.
2. Determine which mounting rod will connect to
canopy.
3. Locate the 1" (25.4 mm) threaded rod.
4. Connect the end of the threaded rod with the
thread sealant to the mounting rod that will
connect to the canopy. Hand tighten securely.
Note: Excess sealant may have to be trimmed
away for best appearance.
5. Place the small, thick, decorative washer onto
the threaded rod.
6. Place the decorative at washer onto the
threaded rod.
7. Place canopy onto threaded rod.
8. Place the other large washer onto the threaded
rod.
9. PlacetheS-HangerTerminal onto thethreaded
rod with tab facing away from canopy.
10. Place star washer onto threaded rod.
11. Screw nut onto threaded rod and tighten se-
curely with wrench.
Nut
Star Washer
S-Hanger Terminal
Flat Washer
Canopy
Decorative Flat Washer
Small, Thick,
Decorative Washer
1" (25.4 mm) Threaded Rod
Mounting Rod
End with Thread
Sealant
WARNING: Turn power off at circuit
breaker or fuse.
1. Removeuniversalmountingbracketfromcanopy
by removing the 3 knurled canopy nuts.
2. Tighten the three canopy screws nger tight.
3. Attach universal mounting bracket to junction
box securely with the two screws provided.

4598-1219-05
WIRING LIGHT FIXTURE
Note: All wiring should be run in accordance with
the National Electrical Code through conduit or
another acceptable means. Contact a qualied
electrician if there is any question as to the
suitability of the system.
1. To simplify installation, at-
tach one end of S-hanger
to S-hanger terminal (lo-
cated inside canopy) and
the other end to mounting
bracket.
Recommended Grounding Method
1. Loop the xture ground wire around the xture
ground screw (located on mounting bracket)
once.
2. Tighten ground screw.
3. Attach end of xture ground wire to the bare
ground wire inside the junction box using sup-
plied wire nut.
If you are uncertain about the grounding method,
consult your local building code.
ASSEMBLE PENDANT LIGHT
1. Route light xture wires through mounting rod
(threaded end rst) that will connect to the
xture.
2. Screw rod into light xture. Tighten mounting
rod securely.
3. Continue this process until desired number of
mounting rods are connected to light xture
(including the rod connected to the canopy).
IMPORTANT: TIGHTEN all connections
securely.
Note: If necessary, trim away any excess thread
sealant for best appearance.
DUALBRITE
®
ON-TIME
TEST 1 510 MIN
OFF 3 6DUSK
TO DAWN
Canopy
Mounting Rod
(Attached to
Canopy)
Light Fixture Wiring
First Mounting Rod
Junction Box
Black to Wire
with Text
Printed On It
Fixture Ground Screw
S-Hanger
S-Hanger
Terminal
S-Hanger
IMPORTANT: This light xture is polarized.
Connect the ribbed wire to the house white
wire. Connect the wire with writing on it to the
house black wire.
White to
Ribbed Wire
Fixture Bare
Ground Wire
Bare Ground
Wire
2. Trim light xture wire length if needed.
3. Connect the junction box wires and the xture
wires together as shown in the following dia-
gram.
4. Twist and secure wires with wire nuts.
Fixture Bare
Ground Wire

5
598-1219-05
Knurled
Canopy Nut
TESTING
1. Turn on the circuit breaker and light
switch.
Note: Sensor has a 1 1/2minute warm up period
before it will detect motion. When rst turned on
wait 1 1/2minutes.
2. To remove sensor cover, unscrew the 4 sen-
sor cover screws holding the sensor cover on
bottom of light xture.
INSTALL PENDANT LIGHT TO
JUNCTION BOX
1. Push wires into the junction box.
2. Remove S-Hanger.
3. Slide canopy onto canopy screws and tighten
knurled canopy nuts securely against the
canopy. Note: Canopy should t tight against
mounting surface.
Canopy Screw
Canopy
BULB INSTALLATION AND
REPLACEMENT
1. Slide door latch up to unlock door. Pull latch to
open door.
2. Install two candelabra base light bulbs (60
Watts maximum each).
3. After installing bulbs, close door and slide latch
down to securely lock door.
DUAL BRITE
®
ON-TIME
TEST 1 5 10 MIN
OFF 3 6DUSK
TO DAWN
DUAL BRITE
®
ON-TIME
TEST 1 5 10 MIN
OFF 3 6DUSK
TO DAWN
Lift Latch Up Open Door
3. SettheON-TIMEswitchtotheTESTpositionand
the DualBrite®switch to the OFF position.
DUAL BRITE
®
ON-TIME
TEST 1 510 MIN
OFF 3 6DUSK
TO DAWN
Sensor
Sensor Cover
Sensor Cover
Nut
DUAL BRITE
®
ON-TIME
TEST 1 5 10 MIN
OFF 3 6DUSK
TO DAWN
DualBrite
®
ON-TIME
DUSK
OFF 3 HR 6 HR TO DAWN
TEST 1 5 10 MIN
Sensor
Lens
4. Walk through the coverage area noting where
you are when the lights turn on. In TESTmode,
light will stay on for only 5 seconds then turn
off.