Hegner LKH 950 Installation instructions

I,
T{EENER
Instruction for Assembly & 0perotion of
DUPLICATING ATTACHMENT LKH 950

':i.i i.l ,
''::; ,... :
Aliqnment of Cutter
Cutter is factory aligned.
.u"i:g supptied gruge (p""i
oy trghtening hex screws.
-2
If
6) cutter has moved, align.cutter byr
as shown in diagram. S""u""-"rtir"
Duplicatinq from a Turninq
Place the turning you rrvish to duplicate between the two centers at
the rear of the, iupii""io; i;; may have to reposition one center
to accomodate the i"ngih-or'iiJ pr""e you are dupricating). Mount
the blank. position "6rr", fp".t rz j-o,r-irp'ii"lt"" so that it rests
at the s m a I l e s t---oilJ"tu","r tn""[i""- t" be copied. Turn
wheel (part 9) counLe."fo"lriue,unti] cutter (part B) is retracted
far enough from br.ank;;-il;t;lank can tu"n ile"ry. Turn on rathe
and lower cutter, by. lu"ninf-rnJur (p;;f gi"i""p,rse untit eutter
starts to cut inro btank. d"il;,1o iurn;;;;"?;"rr ?) r/2 Lo2 rurns
at a time, eaeh time movi"g-irpri"gtiil ;;;;"'ltong. entire rensrh
of turning bv means of J.ari"-"[or."o;#"i-;;'ir,, r";nt of the iathe,
until vou reach tne oesir"i-oi5r"ter in In"-r"llpiece. If you need
to turn more than one dupricate of the ;; ;;., turn rathe off
and set the dupli:,"tol d;il-;;uq" (p""i-iol"""-rhat it rouehes
part lr' Lock depth aa;ustmenE-i;to bosition ji tignt"ning nut (part
No' r5) ' The duori""t;;-;;"'io, "orr"ted properiy to dupricate
additional blanls to identical drameters.
Duplicatinq from a Template
Remove centers for^holding turnings o! duplicator. and mount tempJ-ate
ho'Lders instead'- see oi"g""r'fo" rn*irum'and minimum dimensions
arlowed for temo-r"t"' --ri;il"'tempiaiu"in"i'Jrpr.te horders by
tightenins screws' I*grii"i:rot"i"-n"ii"""""!""pt remprates up ro
i" *;ff:"ffJ.:::. o,piii"i;;-;"
Sharpenino of Cutter
IHPORTANI: Angle of cutter
required, but only from the
the angle of the cutter. must
INNERnot be altered. Sharpen cutter when
care not to alter
surface, taking

fnstruction for Assembly & Operotion of Duplicoting Attochment LKH 950
Mounting of Duplicoting Attochment LKH 950
5
Mount duplicoting ottochment by positioning
fosten to lothe bed with two bolts (tto. l )
(t{o. 2) rest ogoinst lothe bed ond surfoce
unit of reor of lothe ond
supplied. Moke sure surfoces
(No. 3) rests ogoinst
heod stock (Uo. 4).
Remove nut (No. 7) from shoft
Slide spoked wheel onto shoft
6
\
..\
(ruo. 6) ot left front of duplicotor.
(No. 5) ond secure by replocing nut (No.Z).

Duplicoting Attochment LKH 950
Gouging surfoce
z'\
I
-- l- -. I -.- '--.-
tt;
\J
\/
\! '-J.-,'
I
I
Depth
9 Wheel
l5 Nut
?3unu
11
Finger
12
RoIler
13 Arm
8 Cutter
Templote
t/4" tnic*
6 Gouge
I!o
-t
(r)
i-
;x
io
l=

$=:Q-e r\
OJ
a:g E
,xs-6gr{fs
qqs
llY r
EB E E
ra
tO
\r \P€
$:
E-o
rN
IN
lOr
@Y
/a
/a
/o
gN
E4
TI
(o
t
o
//r8
s6-J_ffi=t