BUILDPRO TM Series Manual

1.562.949.8625 | www.stronghandtools.com | [email protected] | 8750 Pioneer Blvd., Santa Fe Springs, CA 90670 U.S.A.
Applicable P/N: TM, TMQ series.
MODULAR WELDING TABLE SETUP INSTRUCTIONS
BUILDPRO
®
Welding Tables
TABLE SETUP
(a)
(b)
Packaging Supporting Legs
(c)
Screw Driver
Round bar
(d)
Leveling
Pad
M20
Nut
Thank you for choosing BuildPro®Modular Welding Tables. Please read all
setup instructions before beginning the setup of your BuildPro® Welding Table.
1. First remove the wooden table cover,
bubble film and anti-rust paper, then use
the forklift to lift the whole table. (or use
other lifting equipment) Remove the
supporting (shipping) legs (4 or 6) based
on the size of the table. (Figures a & b).
2. Place the yellow table legs into the same
screw holes originally used to secure the
shipping legs, then tighten clockwise with
a screwdriver or a round bar smaller than
12 mm (Figure c) by inserting into the
small through-hole in the middle of the
yellow legs.
3. After the table legs are securely installed,
lower the table onto your shop floor.
4. Adjust the Leveling Nuts on each Leveling
Pad until the entire table is level. Tighten
the lock nuts using a wrench. (Figure d)

1.562.949.8625 | www.stronghandtools.com | [email protected] | 8750 Pioneer Blvd., Santa Fe Springs, CA 90670 U.S.A.
MODULAR WELDING TABLE SETUP INSTRUCTIONS
BUILDPRO
®
Welding Tables
over
1T/m
2
Anti
Spatter
Fluid
The following operations may damage table accuracy, and reduce the quality of work and service life:
• Use the surface as ignition board. • Heavy hammering.
• Intense collision or severe impact
between workpiece and table plates.
• The weight of the part to be welded
exceeds the rating of the platform load
capacity (1T/m2evenly distributed).
* Must apply Anti Spatter Fluid around the area to
avoid sticking welding spatter when working on
TM series tables and components. Be careful do
not use under moist, corroded, extreme
temperature environments.
* TMQ series tables have been heat treated [QPQ
treatment] for corrosion and weld spatter resistance.
* Do not disassemble the plates unless you are using it
as table extension. Always re-level and re-position the
plate once it is moved for future accuracy. (Use table
accessories to position the plates)
* Clean the work surface and other components on a
daily basis. Oil protection is recommended.

1.562.949.8625 | www.stronghandtools.com | [email protected] | 8750 Pioneer Blvd., Santa Fe Springs, CA 90670 U.S.A.
MODULAR WELDING TABLE SETUP INSTRUCTIONS
BUILDPRO
®
Welding Tables
MAINTENANCE
* Must apply Anti Spatter Fluid around the area to
avoid sticking welding spatter when working on
TM series tables and components. Be careful do
not use under moist, corroded, extreme
temperature environments.
* TMQ series tables have been heat treated [QPQ
treatment] for corrosion and weld spatter resistance.
* Do not disassemble the plates unless you are using it
as table extension. Always re-level and re-position the
plate once it is moved for future accuracy. (Use table
accessories to position the plates)
* Clean the work surface and other components on a
daily basis. Oil protection is recommended.
* Remove welded parts from the table top after working. Do not leave parts on the table.
* Other temporarily unused components can be coated with oil and stored in a dedicated toolbox, an assigned
tool keeper is required.
* Must use a forklift truck or other lifting equipment (except for a table with casters) to move the workbench.
* When not in use for a long time, tabletop must be protected by anti-rust oil and stored in a dry place. A
wooden cover is recommended.
For more information, please visit www.BuildProTables.com.