HeiSolar Airship BS-AS-15 User manual

Trouble Shooting
1No light at night
Check if the solar panel is blocked from
the sunlight by houses, trees and other
obstacles
Clear obstructions or change installation
location
Check if there is any artificial light
source(s) illuminate on the solar panel
at the night
Remove the artificial light source(s) of
interference or change the installation location
No.Situation Trouble shooting steps Solution
Check the battery have power or not
( There will be a green light flashing on
microwave sensor if the battery have
power)
If all step above have no problem
Test solar panel voltage
Test solar panel voltage at sunshine.if the
volatge of solar panel lower than 10v, please
replaced damaged battery
If the battery voltage is lower than 11 V, the
battery has been protected automatically. Please
use solar panel charge the battery directly (do
not through solar charge controller), after full
charged, battery voltage shows 14V or above
14V, then observe the lighting situation at night
Test battery voltage
Disconnect the cable between the solar panel
and lamp, then connect it again, then press M
button working mode, then wait for 1 min, lamp
will be lighting again
Put the solar lamp in strong sunshine charging
4-6 hours,then observe the lights at night
AIRSHIP SERIES
2A serious shortage
of working time
Clear obstructions or change installation
location
Check if the surface of the solar panel
is dusty or covered
Clean the surface of solar panels as
detailed above
Use the remote control to readjust the
working mode to M
Under normal circumstances, sunny day after
charging the solar panel to observe the lights
at night
Check if the solar panel is blocked from
the sunlight by houses, trees and
other obstacles
Confirm the working mode is correct
or not
Lighting installation area is a long time
cloudy and rainy days (more than 5
days)
3
Check the working mode is corret or not
Check if the air temperature close to
human body temperature
It is out of motion sensor detection range
when installation height exceeds 10m.
It is recommend to reduce the height or
use other operating modes
Lights fail to turn
on properly when
humans approach
adjust working mode to M or U
when the air temperature us close to human
temperature, motion detection may slow
down. It will return to normal after the air
temperature changes
Check if the installation height is
too high
User Manual
Integrated/All In One Solar LED Street Light
Thank you for choosing the Airship Series Solar Street Light. For any questions, please email us.
Please refer to the actual products if the provided diagrams show slight differences.
www.heisolar.com

21 User Manual
AIRSHIP SERIES
Precautions
Before using the Smart Solar Street Light, carefully read
the following precautions to avoid damage or errors.
Product Recycling:
IP65
Product Maintenance:
To ensure effective solar light absorbance, clean
the surface of the panels regularly with water and
a soft cloth. Do not use chemical solutions or
abrasives.
This Solar Street Light operates on a low voltage
DC current. Unless customized otherwise, do not
connect components or ports to an AC current or
any higher rated DC voltage.
Do not replace the original unit with unauthorized
third party parts as they may cause serious
damage to the product. To order replacement
parts or to have them fitted, please visit
www.obluesmart.com or contact your local
distributor.
This product is made from recyclable, high-
performance materials. All materials are compliant
to the RoHS standard. Do not dispose of this
product with other household waste.
Please check your local regulations on collection
and disposal of electronic items. Proper disposal
of used product helps prevent negative impacts
on the environment.
Transportation & Storage:
It is not on the terms of warranty if clients does
modify or refit the light leading to no-proper working
without authorization of factory.
Modification:
Operating Conditions & Limitations:
This product is rated as IP65 protection grade. Do
not exceed the stated operating limits. The
operating temperature range is from -20 ℃ to 60℃
and the charging temperature limit is within 0℃to
60℃. If equipped with heating features, it may be
used between -40℃and 60℃. The heave-duty
structure will survive up to a Category 12 typhoon
or cyclone. (Storms above Category 12 may cause
damages to the product).
This product contains lithium batteries.Please
follow air transport regulations when shipping. It
should be regarded as potentially flammable and
explosive, and be isolated from other goods when
stored, so as to avoid any damage.
The solar panels of this product should be
considered as fragile. There should never be
more than 4 layers of boxes when stacked. To
avoid damage to the panels, make sure no heavy
pressure is applied to the boxes.
Please store the product in temperature between
0℃to 45℃.
If stored for a long period, the product should be
recharged every 6 months. Please only use the
special charger (purchased from manufacturer) to
avoid damage to the battery or device.
Thank you for choosing the AIRSHIP Series Solar Street Light.
Our reserves the rights to amend and improve the product apperance, function and construction
without any prior notification.
Please refer to the actual products if the provided diagrams show slight differences.
Our guarantees that the User Manual has been approved well, but won’t bear the responsibility for
any loss.
www.heisolar.com

3User Manual
AIRSHIP SERIES 4
*
*
*
*
*
*
*
*
*
Introduction:
Product Manual
Application:
Multi options & wide usage:
From 15w to 100w, all in one solar lighting system can be used for a wide range of area lighting.
Public areas & Parks & campuses
Residential & Community Center
Urban trunk road & Slow lane
Bike trails & Tourist attraction
City stadium & Office district
Parking lots & Entrance Lighting
Island & dock & Coastal
Industry & Mining Security & Perimeter
Refugee camp & Temporary Construction
The Airship series is extremely versatile, robust All in One Solar Street Light.
The Airship Light is high powered ‘All In One’ modular solar street and area light with a streamlined
and modern apperance that easily attaches to the top of a round pole without the need for any
further wiring or additional components; It uses an integrated high capacity LiFePO4Lithium Iron
Battery along with a ‘high output’ LED adjustable light source mounted underneath the solar panel
that is perfect for illuminating open space areas.
By choosing a wireless module and wireless concentrator, user can wirelessly control the light,
monitor working status, set custom working mode or review historical charging data. Airship brings
you a easier way to control the outdoor lighting than ever before.
User Notice
Power saving mode
(30% brightness)
Full-power mode
(100% brightness)
To avoid incorrect operation that may lead damage the unit, please read the
following instructions for integrated solar light carefully before installation.
a
b
c
d
e
Airship units do not work without sunlight. Please choose the appropriate model according to
irradiance or peak sun hours for the location of the installation. In areas that are short of sunlight
or after continuous days of rain, Airship units may only work shortly or may not turn on at all. For
areas where this applies we recommend users reduce the power of lamp by use M working mode.
Airship units should be installed with the solar panel facing equator for best performance and
durability. If you are in the northern hemisphere, face the solar panel towards the south as far as
possible when installing the airship seires; if you are in the southern hemisphere, face the solar
panel towards the north.
Make sure to clear trees, building and other shadows, or the internal battery will not charge
properly and the efficiency of the solar panel will be minimized, influencing the working time of
Airship unit.
All internal parts of the Aiship unit are rated IP65 waterproof. Metal parts are anodized rust-proof
die-casting aluminum and galvanized steel which can withstand high temperatures
and humidity weather, no need worried for costa application.
The high strength structure design can withstand wind speed of 180km/h, speed over this may
damage the units.
By factory setting, Airship units turn on at dusk and turn off at dawn automatically. During the
evening, unit works at dim mode( 30%) when humans, car are not around and it will increase light
output to bright mode (100%) immediately when motion sensor is detectd.
www.heisolar.com

5 6
User Manual
AIRSHIP SERIES
Product Manual
Remote Control Technology
DEMO: Test button ( light "on" for 1 mintue).
ON/OFF: On/Off button ( press the button turn on the light,
press again turn off the light, no matter day or night ).
L : 100%-1hr, 70%-3hrs, 20% till dawn.
T: 100%-2hrs, 70%-2hrs, 50%-2hrs.
U: 100%-2hrs, 70%-2hrs, 50%-2hrs, sensor working 50%,
if people come close, 20% far away.
M: 100% if people come close, 30% far away.
6 working modes can be chosen from:
Remark:
After connected the cables between solar panel and the
lamp, the light will turn on automatically when it detect
sunshine (there is no need using remoter to turn on the
solar light ).
Default is M mode, you can choose the best mode according to different sunshine
condition.
*
*
OFF MODE DEMO MODE LIGHT MODE
TIME+
MICROWAVE
MODE
TIME
MODE
MICROWAVE
MODE
To choose working mode from 6 smart modes with remote control.
7
8
6
Parts:
B:
A:
1
1
2
2
6
3
5
5
4
4
10
8
11
7
10
12
9
Microwave sensor
Microwave sensor
Solar charge controller
Solar charge controller
3
Light source
Light source
Support seat
Support foundation
Bracket
Battery box
Battery box
Solar panel
Allen key
Allen key
Solar panel
Bent pipe
Anchor ear
Anchor ear
Open spanner
Remote controller
M8x100
screw 8sets
www.heisolar.com

8
Installation
1. Place the lamp onto the pole and fasten with 6pcs M6x30 screws. ( Refer to figure 1)
2. Finish installation. (Refer to figure 2)
North Road
South Road
Packing List
When opening the package, please confirm that all parts are received as listed below:
Components
Light body
Φ6mm Allen key
User Manual
1pc
1pc
1pc
15W-100W Images
Remote controller 1pc
User Manual
How to turn on our solar street lights ?
Activation:
Notice: Please do not need Press ON button of the small blue remote to turn on the lamp,
because our Airship units have Automatic Activation Function.
The Solar Airship Light will be automically lighting at night without any manually operation.
Airship Unit turn on at dusk and turn off at dawn automatically.
If you want to check whether the Airship Unit are lighting during the daytime:
Cover the solar panels with shelters, the lamp will be lighting.
Press Demo Button after the lighting system has been activated, the lamp will be lighting
for a few mins then turn off automatically.
*
*
Φ76mm
7User Manual
AIRSHIP SERIES
3. Place the lamp onto the pole and
fasten with 6pcs M6 x 30 screws
2. Rotate the base 180 degrees counterclockwise,
then fix it to the lamp body and turn the light
source up
4.Finish installation.
1. Remove the base from the lamp body
Figure 1
A:
B:
Anchor ear B
Components 15W-20W images
ON/OFF DEMO
（L）LightControl
（T）TimingControl
（M）MicrowaveControl
（U）Timing+
MicrowaveControl
ON/OFF DEMO
（L）LightControl
（T）TimingControl
（M）MicrowaveControl
（U）Timing+
MicrowaveControl
Unit main body 1pc
Bent pipe
Anchor ear A
/
/
/
1pc
4setsM8x100 screw
M8x50 screw
Open spanner
User Manual
Remote control
Φ 6mm Allen key
30W-100W
1pc
8sets
2sets
1pc
1pc
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
User Manual
www.heisolar.com

User Manual
AIRSHIP SERIES 109
The drawing of completed installation
M8X50 1pc
Notes:
1. Install the pole in the best position of sunshine. Make sure to be far away from trees,
buildings and other shadows, or the internal battery will not charge properly and the efficiency
of solar panel will be minimized, influencing the working time of unit and battery.
2. After completing installation, please make sure the street light is stable and the switch
is turned on.
3. Suggest use 3mm thickness and 60mm-114mm diameter of the pole.
Step 02:
Fix the anchor ear B to anchor
ear A by fastening 4pcs M8x100
screws, Fix the anchor ear B to the
base of light body by fastening
4pcs M8x100 screws.Fix light
body by fastening 1pc M8x50
screws.
Step 01：
Fix the bent pipe and
mount the anchor ear
A using 2pcs M8x50
screws.
How to install the device?
Installation Height and Distance
Install according to the height and distance (between the lamps) restrictions as set by each
respective product type. Consult our product specialists for special lighting requirements.
Height of pole Distance between polePower
15W 3~5m 10~13m
20W 4~5m 13~16m
30W 5~6m 16~19m
40W 6~7m 19~23m
50W 7~8m 23~27m
60W 7~8m 27~31m
80W 31~35m
8~9m
100W 8~10m 35~40m
N
S
W E
2 PM
M8X50 1pc
M8X100 4pcs
M8X100 4pcs
www.heisolar.com