HeiSolar PHOENIX Series User manual

Trouble Shooting
1No light at night
Check if the solar panel is blocked from
the sunlight by houses, trees and other
obstacles
Clear obstructions or change installation
location
Check if there is any artificial light
source(s) illuminate on the solar panel
at the night
Remove the artificial light source(s) of
interference or change the installation location
No.Situation Trouble shooting steps Solution
Check the battery have power or not
( There will be a green light flashing on
microwave sensor if the battery have
power)
If all step above have no problem
Test solar panel voltage
Test solar panel voltage at sunshine.if the
volatge of solar panel lower than 10v, please
replaced damaged battery
If the battery voltage is lower than 11 V, the
battery has been protected automatically. Please
use solar panel charge the battery directly (do
not through solar charge controller), after full
charged, battery voltage shows 14V or above
14V, then observe the lighting situation at night
Test battery voltage
Disconnect the cable between the solar panel
and lamp, then connect it again, then press M
button working mode, then wait for 1 min, lamp
will be lighting again
Put the solar lamp in strong sunshine charging
4-6 hours,then observe the lights at night
2A serious shortage
of working time
Clear obstructions or change installation
location
Check if the surface of the solar panel
is dusty or covered
Clean the surface of solar panels as
detailed above
Use the remote control to readjust the
working mode to M
Under normal circumstances, sunny day after
charging the solar panel to observe the lights
at night
Check if the solar panel is blocked from
the sunlight by houses, trees and
other obstacles
Confirm the working mode is correct
or not
Lighting installation area is a long time
cloudy and rainy days (more than 5
days)
3
Check the working mode is corret or not
Check if the air temperature close to
human body temperature
It is out of motion sensor detection range
when installation height exceeds 10m.
It is recommend to reduce the height or
use other operating modes
Lights fail to turn
on properly when
humans approach
adjust working mode to M or U
when the air temperature us close to human
temperature, motion detection may slow
down. It will return to normal after the air
temperature changes
Check if the installation height is
too high
PHOENIX SERIES
User Manual
Foldable All In One Solar LED Street Light
Thank you for choosing the PHOENIX Series Solar Street Light. For any questions, please email us.
Please refer to the actual products if the provided diagrams show slight differences.
3User Manual
PHOENIX SERIES

1User Manual
PHOENIX SERIES
Remote Control Technology
DEMO: Test button ( light "on" for 1 mintue).
ON/OFF:On/Off button ( press the button turn on the light,
press again turn off the light, no matter day or night ).
L: 100%-1hr, 70%-3hrs, 20% till dawn. (Timing Mode)
T: 100%-2hrs, 70%-2hrs, 50%-2hrs.
U: 100%-2hrs, 70%-2hrs, 50%-2hrs, sensor working 50%,
if people come close, 20% far away.
M: 100% if people come close, 30% far away. (Sensor Mode)
6 working modes can be chosen from:
Remark:
After connected the cables between solar panel and the
lamp, the light will turn on automatically when it detect
sunshine (there is no need using remoter toturn on the
solar light ).
Default is M mode, you can choose the best mode according to different sunshine
condition.
*
*
OFF MODE DEMO MODE LIGHT MODE
TIME+
MICROWAVE
MODE
TIME
MODE
MICROWAVE
MODE
To choose working mode from 6 smart modes with remote control.
www.heisolar.com 2
Mode M
Mode L
Sensor Lighting Mode
Timing Lighting Mode
30% when no
body
100% when
people come close
01 02
100% brightness
in first hour
01
70% brightness
for 3 hours
02
20% till dawn
03
If need to change lighting mode, pls use the remote at night
When press Button to change mode, light will turn off for 3 mi nets to setup.

www.heisolar.com 4
Installation
A: Fold Installation
B: Unfold Installation
1. Up side screws(4pcs): M8x100 .
2. Down side screws(4pcs) : M8*60 for suggested Φ76mm pole, M8*100 for universal pole
Suggest Pole
Φ76mm
1.Connect the cable between
solar panel and lamp
1.Connect the cable between
solar panel and lamp
2.Connection piece turm up
if fold installation
2.Connection piece turm down
if unfold installation
3.Fix solar street light
onto the pole
3.Fix solar panel and lamp
body onto the pole
Fix lamp body
onto the first
Support Screw
M8*60
Universal Pole
Φ40-114mm
Support Screw
M8*100
Packing List
When opening the package, please confirm that all parts are received as listed below:
Components 15W-100W Images
User Manual
Connection piece
ON/OFF DEMO
（L）LightControl
（T）TimingControl
（M）MicrowaveContro l
（U）Timing+
MicrowaveControl
Unit main body
Anchor ear
1pc
8sets
4sets
3sets
M8x100 screw
M8x60 screw
M6x15 screw
Open spanner
User Manual
Remote control
Φ 6mm Allen key
1pc
2pc
1pc
Φ 3mm Allen key 1pc
1pc
1pc
1pc
3User Manual
PHOENIX SERIES

6
How to turn on our solar street lights ?
Activation:
Notice: Please do not need Press ON button of remote to turn on the lamp,
because our PALM units have Automatic Activation Function.
The Solar PALM Light will be automically lighting at night without any manually operation.
PALM Unit turn on at dusk and turn off at dawn automatically.
If you want to check whether the PALM Unit are lighting during the daytime:
Cover the solar panels with shelters, the lamp will be lighting.
Press Demo Button after the lighting system has been activated, the lamp will be lighting
for a few mins then turn off automatically.
Installation caution
www.heisolar.com
5
In the northern hemisphere,the sun shines from the south
In the southern hemisphere,the sun shines from the north
In order to ensure the solar panel face the sun,when will it fold or unfold?
In northern hemisphere, unfold in north side of road, fold in south side of road
In southern hemisphere, fold in north side of road, unfold in south side of road
When need to fold or unfold?
User Manual
PHOENIX SERIES

User Manual
PHOENIX SERIES
7
40W 4~6m 15~20m
64W 6~8m 20~25m
100W 7~9m 25~30m
120W 8~12m 30~35m
Installation Height and Distance
Install according to the height and distance (between the lamps) restrictions as set by each
respective product type. Consult our product specialists for special lighting requirements.
N
S
W E
2 PM
Height of pole Distance between pole
Power
If any question, you can ask us or watch installation Video
from our website: www.heisolar.com