HENGBO HB-MC-1 User manual
Wireless
Wireless
Wireless
Wireless magnetic
magnetic
magnetic
magnetic door
door
door
door contact
contact
contact
contact user
user
user
user manual
manual
manual
manual
1.
1.
1.
1. Introduction
Introduction
Introduction
Introduction
It
is
mainly used
in
alarm systems, installing generally installed on the edge
of
the door or
window . Once the door or window
is
opened, the m agnetic Sensor will immediately send a
wireless alert signal to the host. This signal containing address and situation information can
make the host identify the location and position
of
the alarm source.
2.
2.
2.
2. Features
Features
Features
Features
The p roduct
us
es SMD production process and has high stability crystal frequency
stabilization , low-power applications IC, with high reliability, frequency stability, low
-
power
consumption .
U sing long-life lithium -a mmonium battery to ensure that products do not have to constantly
replace batteries ; and there are battery monitoring function , low battery indication (led
lights flash
)
and display information on a host
of
low power when battery power
is
low ,
so
as
to remind users to change battery.
43 4.6Mradiofrequencybandmakescommunicationsmorereliable.
3.
3.
3.
3. Technical
Technical
Technical
Technical parameters
parameters
parameters
parameters
Working voltage: DC 3.0v
Static current: ≤ 0.01mA
Frequency:
FSK
43 4.6mhz+FHSS
Battery type: 2400mAh Lithium battery
Wireless transmitting distance: 300m
Operation temperature: －30 ℃~70 ℃
Overall dimension: 79*34*18 mm
4.
4.
4.
4. Encoding
Encoding
Encoding
Encoding settings
settings
settings
settings and
and
and
and applications
applications
applications
applications
Rolling codes act concern with the host.
5.
5.
5.
5. Installation
Installation
Installation
Installation
1) I nstall the lithium -a mmonium battery on the door contact , pay attention to the polarity
of
the battery , please may not hold against ;
2) Make the door contact learn coding information on the host.
T he product
is
required to be installed with screws at base . A long lasting functionality glue
can be used for inconvenient place to use screws . Please remind that the distance between
the subject and the magnet
is
not greater than 8mm ; the center
s
of
the main door sensor
and magnet are
in
the same line. Magnetic magnet can be mounted on either side
of
the
door sensor body ; the door sensor body should be mounted
in
a fixed position , as far as
possible away from the metal shield , to ensure reliable transmission
of
the wireless signal .
6.
6.
6.
6. Precautions
Precautions
Precautions
Precautions
1) When low- power indicator light flashes , please replace the battery .
2) Regular testing work status .
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Table of contents
