Herbeau Royale 3077 User manual

Copyright©2019 Herbeau Creations. All rights reserved. All products and specifications are subject to change without notice. Herbeau Creations is not
responsible for typographical and / or dimensional errors. Typographical errors are subject to correction.
3077 –‘Royale’ Pressure Balance Valve
Part #
Description
01
02
03
04
06
07
08
09
10
11
12
13
91
01
02
03
04
05
06
07
09
11
12
13
14
TRIM
Mounting Plate
Finished Screw
Lille Wall Plate
Bell Escutcheon &
Stem
Handle Screw
Washer
Rubber O-Ring
Handle Stem
Cross Handle
Finished Insert Holder
Black Logo Ceramic
Insert
Hex Nut
Royale Insert Black
Logo Assembly
ROUGH
Screw
Stem
Collar
Screw
Face Plate
O-Ring
Modular Cartridge
Collar
Hex Collar
Hex Nut
½” Handle Ext. Kit
¾” Handle Ext. Kit
Technical Information
Controls temperature.
For ½” rough pressure balance valve.
Available finishes are French Weathered Brass (47), Polished
Chrome (48), SoliBrass (49), Lacquered Matte Black Nickel
(50), Old Gold (52), Old Silver (53), Polished Brass (55),
Polished Nickel (56), Brushed Nickel (57), Satin Nickel (60),
Antique Lacquered Copper (67), Antique Lacquered Brass
(68), Weathered Brass (70), Lacquered Polished Black
Nickel (71) and Lacquered Polished Copper (80).
Please See Cleaning Instructions:
http://herbeau.com/CleaningAll.pdf For Finish Care and
Maintenance Information.
Please follow example when ordering parts for Royale Pres. Bal.
Valve
To order part#10 –Royale Cross Handle
o950064xx
Please substitute finish number needed in place of XX

1 | P a g e
3077 TRIM INSTALLATION
TOOLS NEEDED:
Slotted Screwdriver Plumber’s Grease
Phillips Screwdriver
Small Adjustable Wrench
1. Remove black plastic wall guide and set aside:
2. Remove #2 white plastic stem from rough with Phillips screwdriver and set aside:

2 | P a g e
3. Take #1 mounting plate and place over center of rough with counter-sink holes facing up.
Thread two #2 slotted screws into plate and leave them slightly loose:
4. Take #4 bell and ensure #9 stem is inserted into the back of #4 bell as shown below left.
Insert the assembly through the center of #1 mounting plate and fit it onto the rough
nipple. Now finish screwing #2 slotted screws down tight to secure mounting plate to
rough. (This aligns bell & stem.) Remove #4 bell & #9 stem and set aside for next step:
5. Position #3 wall plate over #2 mounting plate center post. Make sure you align it with the
“Herbeau France” lettering at the top and Froid (cold) and Chaud (hot) are aligned with
the cold and hot rough inlets. Thread #13 locking nut over center post and tighten with
adjustable wrench so wall plate is secure:

3 | P a g e
6. Install #4 bell & #9 stem into center of #3 wall plate and turn the stem fully clockwise.
(Note that #4 bell & #9 stem will sit slightly above the wall plate so it can turn freely
without scratching the wall plate.):
7. Install #10 cross handle onto #4 bell stem ensuring that cross handle is placed
symmetrically:

4 | P a g e
8. Set #7 washer into center of #10 cross handle and thread #6 slotted handle screw into
cross handle tightly with slotted screwdriver.
9. Take #91 logo insert and apply a small amount of plumber’s grease to the rubber o-rings
on the plug. Align correctly and insert the logo plug into the center of the cross handle:
10. Trim is now installed.