Heritage Bathrooms Freestanding Furniture & Wall Hung Cabinet User manual

Instaation Guide
Please keep this booklet for future
Reference.
Installer: when you have read these
instructions please ensure you leave them
with the user.
Models covered:
Freestanding Furniture &
Wall Hung Cabinet

2
Safety Notice .................................................
Installer Guidelines ......................................
Tools Required ..............................................
Installation ......................................................
Shelf Positioning ............................................
Adjustment of Doors ..................................
Caring for your product .............................
Guarantee ......................................................
Notes ..............................................................
Thank you for buying a Heritage Product. When you buy a Heritage product, you can be condent that it
not only features a beautiful, distinctive, classic design, but that it has also been made to the very highest
quality
standards. To ensure that it works to its full potential, it needs to be tted correctly.
These tting instructions have been created to give you all of the information you need and,
if you need any further help, please do not hesitate to give us a call on 0844 701 8503.
Introduction
Contents
3
3
3
4-8
9
9
10
10
11

3
Safety Note
Please read these instructions and retain for future use.
All products manufactured and supplied by Heritage are safe, provided they are installed correctly, used
correctly, and receive regular maintenance in accordance with these instructions.
If you are in any doubt about your ability to install this product safely you must employ the services of an
competent person who has experience of tting products of this nature.
Instaer Guidelines
The furniture in this booklet comes mostly assembled. Shelves will need to be installed once furniture is in
position and xed.
Wall Cabinets will need to be tted on solid walls capable of some load bearing.
The installation of these products greatly depends on the oor and wall being level. If this is not the case, it
must be corrected before installation.
󰖱Before starting any installation project please consider the following:
• Prior to drilling into walls, check there are no hidden electrical wires or cables or water supply pipes
with the aid of an electrical detector.
• If you use power tools do not forget:
- Wear eye protection.
- Unplug equipment after use.
• This product must not be modied in any way as this will invalidate the guarantee.
Tools Required

4
Instaation of Vanity Units
We recommend that you secure the unit to the wall using angled brackets (not supplied). Position the cabinet in
your required location checking the alignment with a spirit level and mark the wall through the holes in the angled
brackets. Make sure you removed required skirting boards before xing. It is best to install the angled brackets on
the inside of the freestanding furniture.
Remove the cabinet and drill holes of the appropriate size to accept the necessary screws or wall plugs used to
secure. Lift the cabinet back into position and screw to the wall.
Make sure you use screws which are shorter length than the thickness of the wood on the freestanding furniture
otherwise you may drill through the unit by mistake and cause irreparable damage.
1
2

5
Instaation of Vanity Units
Locate the basin so it is evenly ush with the edges and rmly against the rear wall. Fasten basin to the wall using
screws (not supplied) or bolts (supplied, if applicable).The holes for these can be seen on the rear of the basin.
Once basin is xed to the wall, run a bead of silicon around the joint between the basin and the vanity unit, this will
ensure the furniture is sealed from water. Handles should be tted by referring to accompanying instructions.
3
4

6
Instaation of Wa Cabinets
1
The hanging brackets are already secured to the cabinet, so you are able to hang cabinet in position on
wall plates by adjusting the plate to allow enough of the hanger to protrude and hook onto the plate.
2
Determine favoured position of cabinet and mark a vertical centre point on the wall. Measure the span
of the pre-tted brackets and transfer measurement to wall measurement out from centre point to give
a central position for the cabinet. Fit the wall plates using appropriate xings (not supplied) using a long
spirit level to make sure levelling is accurate. Plates should be no more wide apart than the spanned
measurement of the wall hanging brackets.
Recommended Fixing diameter 6mm
21.6
63
38
8
21.6
Centre
Rear view of bracket

7
Instaation of Wa Cabinets
3
Turn the top adjustment screw to adjust the unit from front to back.Allows unit to tilt forwards or
backwards from the wall. Insert screwdriver into hole below the top screw and turn to move unit up and
down, adjust unit for height. By adjusting at both sides the unit can be levelled.
4
Once adjustment has been completed, the covering cap can be pressed on, to conceal the hole.
Vertical and horizontal
adjustments
Cabinet hangers should
only be adjusted with a
hand tool and not a
power tool

8
Instaation of Ta Boy Units or Sma Storage Units
1
2
Tall boy units can be attached to the wall using the shown security bracket.There is a purpose access
hole drilled for this on the lower part of the unit, use the provided screw and washer to attach the
bracket to the unit.
Note: Ensure you orientate the bracket as shown in the illustration.
Mark the required hole using the bracket hole as a template. Drill a suitable hole for the wall xings used
(not supplied).Attach the bracket to the wall.
View from rear
View looking inside bottom door

9
Adjustment of drs
Shelf Positioning
All hinges for the cabinets are already installed but may need adjustment to line up the door to the frame.
Push the shelf dowels into pre-drilled holes. Offer shelf into cabinet at an angle, allowing positioning and
lower into place.
Pushes door in or out from unit Alters tilt of doors

10
The condence we have in the quality of our products and services enables us to offer
a free peace-of-mind product guarantee from 2 years up to a lifetime guarantee against
any manufacturing faults, with proof of purchase. In addition, our attentive customer
service team are available to help solve any problems which may arise quickly and
effectively so you can enjoy your bathroom.
To see the specic guarantee for this product, visit the following URL or QR Code.
http://www.heritagebathrooms.com/service-centre/guarantee
Guarantee
Caring for your product
Your tting has a high quality nish and should be treated with care to preserve the visible surface.
A few tips for preventing defects from forming:
Occasionally wipe the surface with a soft damp cloth and dry with a soft dry cloth.
Do no use any abrasive cleaning agents or materials, these will change the surface condition from the
standard nish.

11
Notes

Heritage Bathrooms
Birch Coppice Business Park
Dordon
Tamworth
B78 1SG
Website: www.heritagebathrooms.com
Customer Services Telephone: [phone]
Email: [e-mail]
Contact Details
Freestanding Furniture - D4