Herman Miller Canvas Office Landscape Installation instructions

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 1
Part no. 1b2glt rev R.
YCanvas Office Landscape®90° Connector Installation and
Disassembly for Recycling Instructions
Parts Included:
Connector Tube
(Included with
FT121.X46(2)
FT121.X57(3))
FT122.XX (1))
Light Seal
FT122.2 & XFT121.2XX (1)
FT122.3 & XFT121.3XX (2)
FT122.4 & XFT121.4XX (4)
FT121.246 (4)
FT121.356 (6)
FT121.456 (8)
FT121.257 (6)
FT121.357 (9)
FT121.457 (12)
FT122.XX (4)
Ratchet 9/16” Socket 9/16” Wrench Torque Wrench Safety Glass
A
E
3/8-16 Hex Head
Cap Screw (8 or 12) Washer (8 or 12)
Hardware Pack
C D
Tools Required:
Notice:
Do not tighten screws until at least 2 frames are completely
connected.
Notice:
Make certain that fasteners are torqued to the specied
values.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 2
Part no. 1b2glt rev R.
1
1. Align 3 or 4 wall frames.
2. Connect frames to Top Connector Tube (A) if using the FT121 product using Screws
(C) and Washers (D) at top hole location. For 3 way connection make sure Top
Connector Tube open side faces outward. Do not tighten screws. For change of
height conguration, see next page.
3. Assemble Connector Tube (A) to frames at slot location second from bottom with
Screws (C) and Washers (D). Do not tighten screws.
4. For frames 53” and taller: install Connector (A), Screws and Washers in middle hole.
Important: Torque screws to 200 in-lbs. Start with top connector tube, then
bottom and middle last.
C
CC
D
D
D
A
Do Not
Use
Frame
Frame
Open Side
Frame
Hole
Middle
Hole
Slot Slot
A
Assembly Instructions:

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 3
Part no. 1b2glt rev R.
Change of Height Conguration:
1. When walls of different height are connected, Top
Connector Tube (A) is installed at the top hole
location of the smallest frame.
2. A Connector Tube (A) is installed at the top hole
of shortest frame 46” or smaller.
53” or
Taller Frame
A
Hole
Location
Top Hole
Location
Hole
Location
Slot
Location
1Cont.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 4
Part no. 1b2glt rev R.
Change of Height Conguration Examples:
53” or Taller
Frame
53” or Taller
Frame
53” or Taller
Frame
46” Frame
22”
22”
11”
11”
11”
Hole
Hole
Hole
Hole
Slot
Slot
Hole
Slot
Hole
Slot
A
AA
A
A
A
A
A
A
A

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 5
Part no. 1b2glt rev R.
Change of Height Conguration Examples:
53” or Taller
Frame 53” or Taller
Frame
53” or Taller
Frame
11”
11”
11” or 22”
11” or 22”
46” or Shorter
Frame
22”
Hole
Hole
Hole
Hole
Hole
Hole
Slot
Slot
Hole
Slot Slot
AA
A
A
A
A
A
A
A
A
A

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 6
Part no. 1b2glt rev R.
2
E
E
1. Before cladding has been installed, install Light Seal (E) in inside corners.
2. With the one-inch cut-out in the light seal facing up, rest the top set of arms on the
top connector block.
3. Place one arm so that the curved portion sits well on the bend of the frame.
4. Push the other arm in, so that it snaps. Repeat for the entire length.
5. Cut light seal off even with bottom of frame.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 7
Part no. 1b2glt rev R.
Disassembly for Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling codes.
Use these codes to identify material type for recycling. Non marked components
should be treated as mixed plastic. Ferrous metals can be identied using a
small magnet for recycling. Non-ferrous metals should be separated and recycled
separately.
To disassemble product, reverse the above installation steps.