Herman Miller Canvas Office Landscape Installation instructions

Z
1
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b6y4f rev C.
YCanvas Office Landscape®Universal Work Surface Leg
Installation and Disassembly for Recycling Instructions
Safety Glass
Parts Included:
Tools Required:
Flat Head Tapping
Screw (11)
LH Fully Adjustable LH Fixed
Leg Types
LH Panel Support RH Panel Support
Panel Supports
Support Clip (2)
Long Pan Head
Screw (6)
Short Pan Head
Screw (2)
RH Fully Adjustable RH Fixed
A
C
DE
F
B
Power Driver #2 Phillips Bit 1/8” Drill Bit
Hardware Pack
Hardware Pack

Z
2
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b6y4f rev C.
Fully Adjustable Universal Leg:
1. To adjust leg height; pull Inner Leg out from Outer Leg.
2. Remove Stopper from Inner Leg.
3. Reposition Stopper at desired height location.
4. Insert Inner Leg into Outer Leg, making sure Plastic Sleeve stays located at
end of Outer Leg.
Outer Leg
Outer Leg
Inner Leg
Inner Leg
Stopper
Stopper
Plastic Sleeve

Z
3
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b6y4f rev C.
1. Place Legs (A) onto Work Surface.
2. Position Leg Assembly using dimensions shown.
3. Align 2 holes in each Leg with 2 Pilot Holes in Work Surface.
4. Mark all other holes in Legs.
5. Remove Leg Assembly. Drill Holes. Make sure not to drill thru work surface.
6. Return Leg Assembly to Work Surface.
7. Install 11 Flat Head Screws(B).
AA
A
A
B
.38
.38
1.95
1.95
Freestanding/Peninsula
Work Surface
Wall Attached Work Surface
(front)
(front)
Pilot Holes
Pilot Holes
Pilot Holes Pilot Holes
.50
Universal Leg:

Z
4
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b6y4f rev C.
8. Insert Teeth on Panel Support (C) into slots in frame at desired height.
9. Rotate Panel Support outward. Insert Support Clip(D) into place.
10. Secure Clip in place with 2 short Pan Head Screws(F).
11. Place Work Surface into position aligning 2 inside holes in support with pilot
holes in Work Surface. Mark all screw hole location. Remove Work Surface.
Drill Pilot holes. Be Careful not to drill through Work Surface.
12. Return Work Surface to Panel Support.
13. Install 5 long Pan Head Screws(E) per Support.
Panel Support:
C
E
D
F
Pilot Holes

Z
5
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b6y4f rev C.
1. Place Legs (A) onto Work Surface.
2. Align 2 holes in each Leg with 2 Pilot Holes in Work Surface.
3. Mark all other holes in Legs.
4. Remove Leg Assembly. Drill Holes. Make sure not to drill thru work surface.
5. Return Leg Assembly to Work Surface.
6. Install 11 Flat Head Screws(B) per leg.
A
A
B
Pilot
Holes
Holes
Holes
Universal Leg For D-Shape Work Surface:

Z
6
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b6y4f rev C.
Disassembly and Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling codes. Use
these codes to identify material type for recycling. Non marked components should
be treated as mixed plastic. Ferrous metals can be identied using a small magnet
for recycling. Non-ferrous metals should be separated and recycled separately.
To disassemble product, reverse the above installation steps: