HeroSpeed LongPlus User manual

Quick Start Guide
Please read the Quick Start Guide carefully before using the product and keep it.
Related tools and documents of product, please download from
www.herospeed.net

1. WHAT’S IN THE BOX
2. CAMERA DIAGRAM
1. LED Light
2. Microphone
3. 4MP Camera
4. LED Indicator
5. PIR Motion Sensor
6. Back Shell Open Button
7. Threaded Bracket Interface
8. Strong Magnetic Chuck
9. Speaker
10. Power button & Micro USB Port
Battery Camera Adhesive Tape
USB Cable Screw Set User Guide Mount Bracket
1
2
3
4
5
6
- 1 -
7
8
9

11. Reset hole
12. TF-card Slot
- 2 -
3. BATTERY CHARGING
The batteries inside the Battery camera not fully charged
in accordance with transportation safety regulations.
Please charge the batteries with a USB Cable (5V adapter
not included)，and fully charged for 8-10 hours before installation
11
12
LED Indicator Description
Solid Blue
None
Solid Yellow
Solid Green
Working
Sleep/Power O
Charging
Charging Finished

4. DOWNLOAD THE APP
5. WI-FI SET UP
Download and install the 'LongPlus' app from Google PlayTM or the App StoreTM. The App is also
available by scanning the QR codes on the right, using your QR code scanner in your smart phone.
NOTE:
Google PlayTM is a trademark of Google Inc. App StoreTM is a service mark of Apple Inc.
Before you start the Wi-Fi conguration, please note below:
1). The Battery camera works with 2.4 GHz Wi-Fi, but not with 5 GHz Wi-Fi.
2). Avoid using special characters or symbols like (@~!#$%^&*..., in your Wi- Fi name or password.
3). Perform the conguration near your Wi-Fi router.
- 3 -

- 4 -
Launch the “LongPlus” APP and register an account with your mobile phone number of email ID. Start the
Wi-Fi conguration, following the in-App instructions or refering to the following guiding steps.
Guiding STEPS:
2.Turn on the camera
4.Select Wi-Fi
3.Voice prompt
5.Input password
8.Connection succeeds 9.Check signal strength
10.
Location name
7.Connecting
11.
Adding device complete
1.Tap ”+” to add device
1.Add device 6.
Scan QR code

6. RUN A TEST
After setup, tap on the live view window in the app for a test. Then take your Battery camera outside to
the installation spot and run a test there. Make sure the installation spot is covered by strong 2.4 GHz
Wi-Fi signal. If the battery camera doesn't work well outside, you may need to move the router closer
to the installation spot or invest in a Wi-Fi extender.
7.LIVE VIEW INTERFACE
4
3
7
6
5
9
10
8
- 5 -
11
12 13
Return Home page
Sharing
Settings
Video
Call
Speak
Alarm
Playback
Fullscreen
Screenshot Light control
11
12
Gallary
13
SD/HD

NOTE: LIve viewing will not trigger device recording.
8. PLAYBACK
If the Micro-SD card is properly installed, you can playback the video clips taken after motion
detetion. A 7-days-rolling free cloud storage service is ready for your camera. You can also
upgrade your cloud service pack in the settings.
Tap to upgrade your cloud
recording service pack and
enable Smart Ai Motion
Detetion area customization.
2
3
4
- 6 -
5
Screenshot
Video
Quit Live View
1
2
Speak
3
Call
4
5
Playback button

Steps: Run LongPlus App >> Home >> Setting >> Share >> Camera sharing >> Let the administrator scan your
QR Code.
9. SHARE YOUR DEVICE
10. ALARM SETTING
When a motion is detected by your camera,
you will receive alarm notication from the App.
You can also enable ashlight alarm and siren
alarm to be triggered after motion events.
The ashlight alarm and siren alarm can also
be triggered manually in the camera settings.
- 7 -
Setting

11. INSTALLATION
Adhesive Tape
Nail the screw to the
anchors, or directly to
the wall until the bracket
is xed to the wall.
You can also use the provided
double-sided tape instead of
screws to x the wall mount
on at surface
Attach the camera to the bracket
and adjust the angle to cover the
surveillance area. Do make sure the
camera is within the Wi-Fi range.
- 8 -
LongPlus
App will remind you to charge your camera when the battery is low. Please charge the
camera with the provided Micro USB cable and a DC 5V 1.5A phone charger. During charging, the
camera's LED indicator is in solid yellow, and when the camera is fully charged, the indicator will
turn into solid green. It takes about 8-10 hours to fully charge your camera.
NOTE:

Library UserHome
- 9 -
12.TECHNICAL PARAMETERS
When you connect your camera through the LongPlus App, it will prompt you if the latest rmware is
available. You can also manually check the rmware upgrade in the settings of the App.
Please make sure your camera is fully charged or connected to a power source to upgrade the
rmware. Do not cut o the power when upgrading the rmware.
Network
2.4 GHz ~ 2.4835 GHz
IEEE 802.11 b/g/n
Within 3 ~ 4 Sec
Software
VicoHome
iOS, Android
Within 2 ~ 4 sec
Push notication within 2 ~ 4 sec
General
Video & Audio
Storage
System
4
Ingenic T31ZX
2560 1440
3