HFCL io XPON ONT OHG-5110-E14A User manual

Quick
Start
Guide
XPON ONT
OHG-5110-E14A
Sleek | Smart | Secure

Thank you for choosing XPON ONT
Packaging Content
XPON ONT (Qty:1)
Power
Adaptor(Qty:1)
Ethernet
Cable(Qty:1)
Introduction
02
If you find anything missing or damaged,
contact the service provider.
Note:

Product Overview
Working Environment
PRODUCT INTERFACE INFO
OHG-5110-E14A
1 x SC/UPC or 1 x SC/APC GPON Port
4 x 10/100/1000Mbps LAN
1 x POTS Port
2.4G + 5G (2*2MIMO)
1 x USB Port
XPON ONT OHG-5110-E14A
Weight About 400 gm
(include power adopter)
Maximum < 8W
power consumption
Working temperature 0ºC - 50ºC (32ºF - 122ºF)
Storage temperature -40ºC - 70ºC (-40ºF - 158ºF)
Working humidity 10% - 95%, non-condensing
Storage humidity 5% - 95%, non-condensing
03

04
Hardware Installation
Use an optical fiber to connect the optical port on the
ONT Configure IP Address of Network Card
1.
Press the Wi-Fi switch to enable the Wi-Fi access function.
By default, this function is enabled.
6.
Press the WPS switch to enable the WPS encryption function.
7.
Before enabling the WPS encryption function of a XPON ONT
terminal, ensure that the function is set in the
system software in advance. After success- full setting,
press the WPS switch for the settings to take effect.
7.1.
Use a network cable to connect the LAN port
to an Access Point.
2.
Use a phone line to connect the PHONE port
to a phone or fax machine.
3.
Use a power adapter to connect the DC12V port
to the power socket.
4.
Do not use any power adapters that are not in the standard
configuration. Otherwise, the device may be abnormal or unsafe.
4.1.
Press the ON/OFF power switch.
5.
The optical connector connected
to the PON port is an SC/APC or SC/UPC connector.
1.1.
To ensure normal use of fibers, make sure that
the fiber bend radius is larger than 30 mm.
1.2.

Configure IP Address of Network Card
Internet Settings
Web login
05
• Configure TCP/IP properties of your network card to obtain
an IP address automatically from ONT, or set the IP address
of the computer with the same network mask of the ONT.
• The default management IP address and subnet mask of the
XPON ONT are as follows:
- IP address: 192.168.1.1
- Subnet mask: 255.255.255.0
• Open browser, and input “http://192.168.1.1” in the address
bar and press enter.
• In the Quick Configuration page that is displayed, enter the
user name, password and click on login button.
• The user name is “admin”and the password is “system”.
Input username and password
Username:
Password:
Login

OHG-5110-E14A
interfaces and buttons
06
Antennas
Reset
USB
RJ11 WPS
DC Jack
RJ45
Power Switch
LED COLOR STATUS
The optical port is equipped with a rubber
plug and is connected to an optical fiber
for transmission
RJ-11 POTS port for connecting to analog
telephones Call forwarding, Call waiting,
Call block, 3-way conference call, etc.
RJ-45 GE Ethernet interface used to
connect the Ethernet interface of the
computer
Press for 6S above, Restoring Default
Settings
Enable/Disable the 2.4Ghz and 5Ghz
wireless code function
12V DC power input interface to connect
the power adapter
A power switch used to connect or
disconnect a device's power supply
Press for 0-3S, WPS
PON
PHONE
LAN 1 - 4
RST
Wi-Fi
DC12V
ON/OFF
WPS

OHG-5110-E14A indicator light
To mount the Access Point on a wall, use the wall mounting
bracket, drywall screws, and screw anchors (* The entire wall
mounting assembly is sold separately)
07
LED
FUNCTION
LED
MARK COLOR LED
STATUS DESCRIPTION
Power Status PWR
On
Green
The device is receiving
power and working properly
Wi-Fi Status 2.4G/5G
On
Green
Wi-Fi Enabled
Off Wi-Fi Disabled
Blink Wi-Fi is Transmitting /
Receiving
PON Status
PON
On
Green
The device is linked
successfully to an OLT
LAN Status LAN 1
- LAN 4
Off
Green
Optical signal reception
is normali
Off
On
Indicates that LAN port
is not connected
Connected properly
Blink LAN port is being
transferred data
LOS
Blink
Red
The device receives optical
power below its sensitivity
Off The PON link
is down
Blink The device is initializing
to an OLT
Off The power
supply is cut off

08
Avoid staring directly into the optical port without wearing eye
protection
Store the device safely away from children to prevent
accidental ingestion
Ensure device's power supply voltage matches its input
requirements
Avoid foreign objects, especially metal, from entering the
device through the heat dissipation hole
Prior to handling cables, ensure your hands are dry. Always
turn off the device and power before connecting or
disconnecting cables
Turn off power, unplug all cables (power, optical fiber, and
network) during lightning. Ensure accessible socket
placement. Check power adapter for damage before use
To prevent device damage, keep optical fiber strength
members and metal parts out of indoor spaces
Safety Precautions

09
Keep the device away from large heat source equipment, bare
flames, and high-power devices, such as electric heaters, candles,
and blow dryer
Replace aging cables or power sockets near the device
promptly to eliminate safety risks. Ensure the device's
power supply voltage matches its input requirement
Avoid placing objects on the device to prevent overheating or
deformation
Do not dismantle the device without authorization. In case of
a malfunction, contact the authorized service center
Do not modify the device's structure, safety features, or
performance without prior authorization
Fireproof Precautions:

HFCL Limited All Rights Reserved. HFCL and io by HFCL are trademarks or registered
trademarks of HFCL Ltd. Specifications are subject to change without notice.
8, Commercial Complex,
Masjid Moth, Greater Kailash-II,
New Delhi- 110048
[email protected]
hfcl.com | io.hfcl.com
Contact Us:
by HFCL
Revision: A
Part Number: QSG-05-0001