Hifonics TPS-MR1 Manual

Operators Guide
TPS-MR1
Bluetooth Device Pairing
The pairing process can vary based on your particular device. Refer to the
operating instructions of your device. Below is the general process to connect.
Under the Bluetooth mode, the status indicator will ash slowly “BT music”and search
for the last paired device. If no device is located, it will ash quickly indicating it is ready
to pair to a new device.
On your Bluetooth enabled device, search for “HIFONICS” under Bluetooth settings.
Select HIFONICS, wait for the device to indicate “CONN OK.”
Music will now play through the system.
To connect to a different device while currently paired, press and hold the
PLAY/PAUSE button. This will initialize pairing mode.
FWD / Forward – This multi-function button works with your music sources. In radio
mode, quickly press to go forward to the next strongest station.
For other sources, press quickly to go to the beginning of the next song. Press and hold
for fast forward within the current selection.
1 - Play / Pause – This multi-function button works in several modes. For the BT, USB,
Apple Device mode this is play and pause.
In FM and AM mode quickly press to select station pre-set #1.
In radio mode press and hold to store the current station to this pre-set.
2 - INT / Intro – This multi-function button works in several modes. For the USB, press
this to play the introduction (rst 10 seconds) of each track. Press again to turn off the
feature. (not compatible in iPod mode)
In FM and AM mode quickly press to select station pre-set #2.
In radio mode press and hold to store the current station to this pre-set.
3 - RPT / Repeat – This multi-function button works in several modes. For the USB,
press this button to repeat the current song. Press again to turn off the feature. (not
compatible in iPod mode)
In FM and AM mode quickly press to select station pre-set #3.
In radio mode press and hold to store the current station to this pre-set.
4 - RDM / Random – This multi-function button works in several modes. For the USB,
press this button allow random songs to play from that unit. The RDM will not select
random tracks from different devices, only from the unit selected.
(not compatible in iPod mode)
In FM and AM mode quickly press to select station pre-set #4.
In radio mode press and hold to store the current station to this pre-set.
8
9
10
11
12
Controls

CAUTION
Always consider consulting a professional audio installer before
installing any audio components. Be careful and take your time.
Do not let wires make contact with metal edges or hot engine
components.
U-Bracket Mounting
Controls
1
2
3
4
5
6
3
1
2
4
5
56
78
910
11 12
Break Joints
Mounting Surface
U-Bracket
Mounting Nuts
Radio Antenna
USB Connector
Red - Front RCA Output (R)
White - Front RCA Output (L)
Red - Rear RCA Output (R)
White - Rear RCA Output (L)
Red - RCA Input (R) AUX 1
White - RCA Input (L) AUX 1
Red - RCA Input (R) AUX 2
White - RCA Input (L) AUX 2
Accesory
+12 Volts
White - Front Left (+)
White/Black - Front Left (-)
Gray - Front Right (+)
Gray/Black - Front Right (-)
Green - Rear Left (+)
Green/Black - Rear Left (-)
Purple - Rear Right (+)
Purple/Black - Rear Right (-)
Black - Ground (-)
Blue - Remote Output
Wiring
Power On / Off / MUTE – The power button is a multi-function button, depending on
how long you hold the button. One Quick press of the power button when the unit is
off, will turn it on. One Quick press of the power button when the unit is on will mute the
output. Press and hold turns power off.
Audio Mode – Press the button quickly, to see show ‘SEL’ on the screen. Then with
quick presses scroll through each of the audio functions: BASS, TRE, BAL, FAD,
LOUD, EQ, BEEP, and regional radio settings (PREA EUR/USA) under FM/AM mode.
Each function is adjusted using the # 5 button VOL Up/Down.
APS – In FM or AM Mode, Press the button quickly to scan stored radio stations. Press
and hold to automatically scan all stations programmed with a short audition of each.
Press the button again to stop the scan.
MOD – This is your input mode switch. Press to scroll through your various inputs FM,
BT, IPOD, USB, AUX1, and AUX2.
VOL – Volume Up / Down. Press quickly for small increments in volume, hold down for
quicker adjustments.
BND / Clock – This multi-function button when pressed quickly, scrolls between your
FM1, 2 and 3 plus AM1 and 2 banks for programmed stations.
Press and hold button 6 to enter clock mode. Press button 6 once more to enter clock
adjust mode. Pressing it once more will toggle between hours and minutes. Use the
Vol^ and Vol˅ buttons to adjust the time.
RWD / Back – This multi-function button works with your music sources. In radio mode,
quickly press to go back to the next strongest station.
For other sources, press quickly to go back to the beginning of the current song, press
twice to go back to the beginning of the previous track. Press and hold for fast reverse
within the current selection.
7
Discover other marine electronics & navigation on our website.
Direct Screw-Type Mounting
1. Use a small at head screw driver under the edge of the button door and apply
upward pressure until the button panel’s clips release and it lifts up.
2. Pull door away from the radio until it is detached from the radios face plate.
3. Position the radio in the location that is desired.
4. Use the screws included and screw the unit in place.
5. Reinstall the button doors.