highmore Rocko HM-WB001-001 User manual
Imported By: Forward Industries, 33401. U.S.A
Rocko
Motorized Height Adjustable
Workbench With Pegboard
User Manual
Product Ref-HM-WB001-001
Issue 1 - 09/09/21
Power Supply: AC adapter, 100-240V~ 50/60Hz
Service Environment: 32-104°F
507lbs.
1
DANGER – To reduce the risk of electric shock:
1. Unplug the power plug before cleaning, wipe the dust on surface with damp cloth when cleaning. Be careful
not to let water drops into the internal parts, or loose the connector.
2. Check carefully to ensure correct and complete assembly before using.
4. Don’t allow children to play near the desk as their behavior is unpredictable. The manufacturer is not responsible
use of the equipment.
6. Do not use corrosive or abrasive materials are near the equipment. Please ensure that the cleaner used will not
pollute the environment.
person in order to avoid a hazard.
choking hazard to children.
11. We recommend you keep the original package of the equipment if necessary in case of the future use in
12. Do not use outdoors.
2
recommended by the manufacturer.
15. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been
16. Keep the cord away from heated surfaces.
18. For grounded products the following statement:
provided on a double-insulated product, nor is a means for grounding to be added to the product. Servicing a
A double-insulated product is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED.” The symbol
SAVE THESE INSTRUCTIONS
For Household use only
SERVICING OF DOUBLE-INSULATED PRODUCTS
Transmission
Connector Qty 1
Transmission rod Qty 1
Table Top Qty 1
Leg Qty 1
Foot Qty 2
Controller Qty 1
Leg Support Qty 1
Transmission Cover Qty 1
3
Power cable Qty 1
Peg board Qty 2
Pegboard Support
Pegboard Support
4
A
B
C
D
H
Allen key Qty 1
4x4
Spanner
2.5x2.5
5
F
E
G
Not Supplied
Assemble feet to
legs and using
screws .
Assemble legs and
to the underside
of table top using
screws .
IMPORTANT
During assembly, ensure the height of the
legs remains the same on both sides!
C
G
C
H
4x4 Qty 1
G
H
6
STEP 1
STEP 2
C
G
SHOWN UPSIDE DOWN
SHOWN UPSIDE DOWN
Underside
Front
Back
Front
Back
4x4 Qty 1
a. Slide transmission
connector onto one
end of transmission
rod .
b. Locate the other end of
transmission rod into
the hole in the side of
leg .
c. Slide transmission
is equally located between
transmission rod and
the short transmission
rod in leg .
d. Secure using grub
screws .
IMPORTANT-Ensure the
legs and remain at
the same height
throughout.
7
STEP 3
SHOWN UPSIDE DOWN
A
H
2.5x2.5 Qty 1
A
Front
Back
d.
A
A
H
Tighten
Screw aligned with the slot on the hexagonal rod
b.
Insert
a.
Spin
c.
8
Assemble transmission
cover in between
legs and using
screws .
B
STEP 4
B
H
4x4 Qty 1
SHOWN UPSIDE DOWN
Front
Back
a. Remove the caps on each
end of leg support .
b. Ensuring the small holes
are facing up as shown.
assmble leg support to
the back of legs and
using screws .
c. Replace the caps into leg
support .
D
H
Spanner Qty 1
STEP 5
Small hole up
D
SHOWN UPSIDE DOWN
Front
Back
B
H
B
b.
D
H
b.
Remove the
cap
a.
Cover with
cap
c.
D
D
Complete all cable
Cab
be used to route and
secure cables as
required.
9
STEP 7
F
SHOWN UPSIDE DOWN
Assembly controller
to the underside of the
the screws supplied
with the controller.
STEP 6
SHOWN UPSIDE DOWN
Front
Back
Not Supplied
Front
Back
a.
b.
c.
Port for
controller
Power port
Port for cable
connected to the
a. Power
Controller
b. c.
F
F
Cable
management
F
tabletop and keep them organized.
F
F
With help, locate
pegboards in
between supports
and .
Secure using screws
and spring washers .
With help, stand the
desk upright.
Warning the desk is
heavy, li� with care.
Assemble pegboard
supports and to
the underside of table
top using screws
and spring washers .
C
E
E
10
STEP 8
STEP 9
C
E
C
C
E
C
Front
Front
Back
Back
C
C
C
E
SHOWN FROM BACK
E
E
C
E
C
E
E
STEP 10
11
Height Adjustment/Controls
Controller
Press the “▲”or “▼” keys to raise or lower the desk top.
▼
completed.
Reconnect to the power and press “▼” key to start the reset process.
Up key
Down key
Assembly is complete
unit because it is faulty or is no longer wanted, please contact our product returns department at
Address: Forward Industries, 105 South Narcissus Avenue Suite 412, West Palm Beach, FL 33401
12
Troubleshooting
below.
This marking indicates that this product should not be disposed with other household
wastes. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
retailer where the product was purchased. They can take this product for environmental
safe recycling.
Certification
Fault phenomenon Method
2.Contact your supplier or dealer;
Overwork
（Duty cycle: ax 2min on/30min OFF）
1.Check if the equipment load is too heavy
to exceed 230KG
2.Contact your supplier or distributor
1.Restart after suspend for 30 mins while
connecting with power;
2.Contact your supplier or dealer
1.Check if all the cables be connected well
No response while long
pressing down arrow after
connected with a power supply
Bottom cannot rise
Table of contents
Other highmore Indoor Furnishing manuals
Popular Indoor Furnishing manuals by other brands
Regency
Regency LWMS3015 Assembly instructions
Furniture of America
Furniture of America CM7751C Assembly instructions
Safavieh Furniture
Safavieh Furniture Estella CNS5731 manual
PLACES OF STYLE
PLACES OF STYLE Ovalfuss Assembly instruction
Trasman
Trasman 1138 Bo1 Assembly manual
Costway
Costway JV10856 manual
