Hilti TE1 User manual

TE 1
Bedienungsanleitung de
Operating instructions en
Mode d’emploi fr
Istruzioni d’uso it
Manual de instrucciones es
Manual de instruções pt
Gebruiksaanwijzing nl
Brugsanvisning da
Bruksanvisning sv
Bruksanvisning no
Käyttöohje fi
Οδηγιες χρησεως el
Lietošanas pamācība lv
Instrukcija lt
Kasutusjuhend et
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

1
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

2
4
6
5
3
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

ORIGINAL OPERATING INSTRUCTIONS
TE 1 rotary hammer
It is essential that the operating instructions
are read before the power tool is operated for
the first time.
Always keep these operating instructions to-
gether with the power tool.
Ensure that the operating instructions are
with the power tool when it is given to other
persons.
Contents Page
1 General information 12
2Description 13
3 Tools 14
4 Technical data 15
5 Safety instructions 16
6Beforeuse 18
7 Operation 18
8 Care and maintenance 19
9 Troubleshooting 20
10 Disposal 20
11 Manufacturer’s warranty - tools 21
12 EC declaration of conformity (original) 21
1These numbers refer to the corresponding illustra-
tions. The illustrations can be found on the fold-out cover
pages. Keep these pages open while studying the oper-
ating instructions.
In these operating instructions, the designation “the
power tool” always refers to the TE 1 rotary hammer.
Parts, operating controls and indicators 1
@Chuck
;Control switch
=Forward / reverse switch
%Lockbutton for sustained operation
&Dust shield
(Side handle with depth gauge
)Supply cord
1 General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that will lead to
seriousbodilyinjuryorfatality.
WARNING
Draws attention to a potentially dangerous situation that
could lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that
could lead to slight personal injury or damage to the
equipment or other property.
NOTE
Draws attention to an instruction or other useful informa-
tion.
1.2 Explanation of the pictograms and other
information
Warning signs
General
warning Warning: electricity
en
12
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

Obligation signs
Wear eye
protection Wear a hard hat Wear ear protection Wear protective
gloves
Wear
breathing
protection
Symbols
Read the
operating
instructions
before use
Return waste
material for
recycling.
Forward /
reverse Amps
Hertz Watts Volts Revolutions
per minute
Location of identification data on the power tool
The type designation and serial number can be found
on the type identification plate on the machine or tool.
Makeanoteofthisdatainyouroperatinginstructions
and always refer to it when making an enquiry to your
Hilti representative or service department.
Type:
Generation: 02
Serial no.:
2 Description
2.1 Use of the product as directed
The power tool is an electrically-powered rotary hammer with pneumatic hammering mechanism.
The power tool is designed for professional use and may be operated, serviced and maintained only by trained,
authorized personnel. This personnel must be informed of any special hazards that may be encountered. The power
tool and its ancillary equipment may present hazards when used incorrectlybyuntrainedpersonnelorwhenusednot
as directed.
The power tools are designed for drilling in concrete and masonry.
The working environment may be as follows: construction site, workshop, renovation, conversion or new construction.
Thepowertoolmaybeusedonlyinadryenvironment.
To avoid the risk of injury, use only genuine Hilti accessories and insert tools.
Observe the information printed in the operating instructions concerning operation, care and maintenance.
The power tool may be operated only when connected to a power supply providing a voltage and frequency in
compliance with the information given on its type identification plate.
Do not use the power tool where there is a risk of fire or explosion.
Working on materials hazardous to the health (e.g. asbestos) is not permissible.
Modification of the power tool or tampering with its parts is not permissible.
2.2 Chuck
TE‑C CLICK chuck
2.3 Switches
Control switch with electronic speed control
Lockbutton for sustained operation
en
13
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

Forward / reverse switch
2.4 Grips
Pivotable side handle with depth gauge
Vibration-absorbing grip
2.5 Protective feature
Mechanical slip clutch
2.6 Lubrication
Grease lubrication
2.7 Items supplied as standard
1 Power tool
1 Operating instructions
1 Hilti cardboard box or toolbox
2.8 Using extension cords
Use only extension cords of a type approved for the application and with conductors of adequate cross section. The
power tool may otherwise loose performance and the extension cord may overheat. Check the extension cord for
damage at regular intervals. Replace damaged extension cords.
Recommended minimum conductor cross section and max. cable lengths
Conductor cross section 1.5 mm² 2.5 mm² 3.5 mm²
Mains voltage 110-127 V 30 m 50 m
Mains voltage 220-240 V 75 m 100 m
Do not use extension cords with 1.25 mm² conductor cross section.
2.9 Using extension cords outdoors
When working outdoors, use only extension cords that are approved and correspondingly marked for this application.
2.10 Using a generator or transformer
This power tool may be powered by a generator or transformer which fulfills the following conditions: The unit must
provideapoweroutputinwattsofatleasttwicethevalueprintedonthetype identification plate on the power tool.
The operating voltage must remain within +5% and -15% of the rated voltage at all times, frequency must be in the 50
– 60 Hz range and never above 65 Hz, and the unit must be equipped with automatic voltage regulation and starting
boost.
Never operate other power tools or appliances from the generator or transformer at the same time. Switching other
power tools or appliances on and off may cause undervoltage and / or overvoltage peaks, resulting in damage to the
power tool.
3Tools
Designation Description
Hammer drill bits, short ∅ 4…18 mm, Hammer drilling in concrete, masonry and
natural stone
Hammer drill bits, long ∅ 4…18 mm, Hammer drilling in concrete, masonry and
natural stone
en
14
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

4 Technical data
Right of technical changes reserved.
NOTE
The power tool is available in various voltage ratings. Please refer to the power tool’s type identification plate for
details of its rated voltage and rated input power.
Power tool TE 1
Rated power input 650 W
Rated current input Rated voltage 110 V: 6.5 A
Rated voltage 120 V: 6.5 A
Rated voltage 127 V: 6.5 A
Rated voltage 220 V: 3.1 A
Rated voltage 230 V: 3.0 A
Rated voltage 240 V: 2.9 A
Mains frequency 50…60 Hz
Weight in accordance with EPTA procedure 01/2003 2.4 kg
Dimensions(LxWxH) 330mmx79mmx203mm
Hammer drilling speed 0…930/min
Hammering speed 0…4,500/min
Single impact energy in accordance with EPTA proced-
ure 05/2009 1.5 J
Other information about the power tool
Drilling performance in medium-hard concrete ∅ 8 mm: 25 cm³/min
∅ 10 mm: 33 cm³/min
∅ 12 mm: 35 cm³/min
Protection class as per EN Protection class II (double insulated) as perEN 60745‑1
NOTE
The vibration emission level given in this information sheet has been measured in accordance with a standardised test
giveninEN60745andmaybeusedtocompareonetoolwithanother.Itmaybeused for a preliminary assessment
of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is
used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total working period. An estimation of the level of exposure to
vibration should also take into account the times when the tool is switched off or when it is running but not actually
doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety
measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
Noise and vibration information (measured in accordance with EN 60745):
Typical A-weighted sound power level 100 dB (A)
Typical A-weighted emission sound pressure level 89 dB (A)
Uncertainty for the given sound level as per EN 60745 3 dB (A)
Additional information in accordance with EN 60745
Triaxial vibration values (vibration vector sum) Measured in accordance with EN 60745‑2‑6
Hammer drilling in concrete, ah, HD 15 m/s²
Uncertainty (K) 1.5 m/s²
en
15
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

5 Safety instructions
5.1 General Power Tool Safety Warnings
a) WARNING
Read all safety warnings and all instructions. Fail-
ure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference.
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
5.1.1Workareasafety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
5.1.2 Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any ad-
apter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
theriskofelectricshock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
5.1.3 Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off‐position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before turn-
ing the power tool on. A wrench or a key left at-
tached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
5.1.4 Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for opera-
tions different from those intended could result in a
hazardous situation.
en
16
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

5.1.5 Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
5.2 Hammer safety warnings
a) Wear ear protectors. Exposure to noise can cause
hearing loss.
b) Use auxiliary handles, if supplied with the tool.
Loss of control can cause personal injury.
c) Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
5.3 Additional safety precautions
5.3.1 Personal safety
a) Keep the grips dry, clean and free from oil and
grease.
b) Check that the side handle is fitted correctly and
tightened securely.
c) Wearadustmask.
d) Improve the blood circulation in your fingers by
relaxing your hands and exercising your fingers
during breaks between working.
e) Children must be instructed not to play with the
power tool.
f) The power tool is not intended for use by children,
by debilitated persons or those who have received
no instruction or training.
g) Avoid touching rotating parts. Switch the power
tool on only after bringing it into position at the
workpiece. Touching rotating parts, especially rotat-
ing insert tools, may lead to injury.
h) Always lead the supply cord and extension cord
away from the power tool to the rear while work-
ing. This helps to avoid tripping over the cord while
working.
i) Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory diseases
to the operator or bystanders. Certain kinds of dust
are classified as carcinogenic such as oak and beech
dust especially in conjunction with additives for wood
conditioning (chromate, wood preservative). Material
containing asbestos must only be treated by special-
ists. Where the use of a dust extraction device is
possible it shall be used. To achieve a high level
of dust collection, use a suitable vacuum cleaner
of the type recommended by Hilti for wood dust
and/or mineral dust together with this tool. Ensure
that the workplace is well ventilated. The use of a
dust mask of filter class P2 is recommended. Fol-
low national requirements for the materials you
want to work with.
5.3.2 Power tool use and care
a) Secure the workpiece. Use clamps or a vice to
secure the workpiece. The workpiece is thus held
more securely than by hand and both hands remain
free to operate the power tool.
b) Check that the insert tools used are compatible
with the chuck system and that they are secured
in the chuck correctly.
c) In the event of a power failure or interruption in the
electric supply, switch the power tool off, unplug
the supply cord and release the switch lockbutton
(if applicable). This will prevent accidental restarting
when the electric power returns.
d) Avoid applying an excessive amount of grease to
the drill bit connection end. Grease may otherwise
be forced out of the chuck when the power tool is in
operation.
5.3.3 Electrical safety
a) Before beginning work, check the working area
(e.g. using a metal detector) to ensure that no
concealed electric cables or gas and water pipes
are present. External metal parts of the power tool
may become live, for example, when an electric cable
is damaged accidentally. This presents a serious risk
of electric shock.
b) Check the power tool’s supply cord at regular
intervals and have it replaced by a qualified spe-
cialist if found to be damaged. If the power tool’s
supply cord is damaged it must be replaced with
a specially-prepared supply cord available from
Hilti Customer Service. Check extension cords
at regular intervals and replace them if found to
be damaged. Do not touch the supply cord or
extension cord if it is damaged while working.
Disconnect the supply cord plug from the power
outlet. Damaged supply cords or extension cords
present a risk of electric shock.
c) Dirty or dusty power tools which have been used
frequently for work on conductive materials
should be checked at regular intervals at a Hilti
Service Center. Under unfavorable circumstances,
dampness or dust adhering to the surface of
the power tool, especially dust from conductive
materials, may present a risk of electric shock.
d) When working outdoors with an electric tool
check to ensure that the tool is connected to the
electric supply by way of a ground fault circuit
interrupter (RCD) with a rating of max. 30 mA
(tripping current). Use of a ground fault circuit
interrupter reduces the risk of electric shock.
e) Use of a ground fault circuit interrupter (RCD
residual current device) with a maximum tripping
current of 30 mA is recommended.
en
17
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

5.3.4Workareasafety
a) Ensure that the workplace is well ventilated. Ex-
posure to dust at a poorly ventilated workplace may
result in damage to the health.
b) Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Fragments
of workpiece or of a broken accessory may fly
away and cause injury beyond immediate area of
operation.
c) If the work involves breaking right through, take
the appropriate safety measures at the opposite
side. Parts breaking away could fall out and / or fall
down and injure other persons.
5.3.5 Personal protective equipment
The user and any other persons in the vicinity must
wear suitable eye protection, a hard hat, ear protec-
tion, protective gloves and breathing protection while
the tool is in use.
6Beforeuse
6.1 Fitting the side handle 2
CAUTION
Remove the depth gauge from the side handle in order
to avoid injury.
1. Disconnect the supply cord plug from the power
outlet.
2. Release the side handle clamping band by turning
the handle counterclockwise.
3. Slide the side handle clamping band over the chuck
and onto the cylindrical section at the front end of
the power tool.
4. Pivot the side handle into the desired position.
5. CAUTION Check that the clamping band is en-
gaged in the groove provided on the power tool.
Securethesidehandlebyturningthegripclockwise.
6.2 Use of extension cords and generators or
transformers
Please refer to the “Description” section.
7Operation
WARNING
The electric supply voltage must comply with the
information given on the type identification plate on
the power tool.
CAUTION
Check that the side handle is fitted correctly and
tightened securely.
CAUTION
In the event of the drill bit sticking, the power tool will
pivot about its own axis. Always use the power tool with
the side handle fitted and hold it securely with both
hands so that the resulting opposing force causes
the slip clutch to release in the event of the drill bit
sticking. Use clamps or a vice to hold the workpiece
securely.
7.1 Preparing for use
CAUTION
Remove the depth gauge from the side handle and
the insert tool from the chuck in order to avoid injury.
CAUTION
Wear protective gloves when changing insert tools as
the insert tools get hot during use.
7.1.1 Adjusting the depth gauge 3
CAUTION
Use only a depth gauge with a maximum length of
180 mm.
1. Release the side handle clamping band by turning
the handle counterclockwise.
2. Pivot the side handle into the desired position.
3. Adjust the depth gauge to the desired drilling depth.
4. Tighten the side handle securely by turning the
grip section. This also clamps the depth gauge in
position.
en
18
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

7.1.2 Fitting the insert tool 4
1. Disconnect the supply cord plug from the power
outlet.
2. Check that the connection end of the insert tool is
clean and lightly greased. Clean it and grease it if
necessary.
3. Check that the sealing lip of the dust shield is clean
and in good condition. Clean the dust shield if ne-
cessary or replace it if the sealing lip is found to be
damaged (please refer to the “Care and mainten-
ance” section).
4. Push the insert tool into the chuck and rotate it while
applying slight pressure until it engages in the guide
grooves.
5. Push the insert tool further into the chuck until it is
heard to engage.
6. Check that the insert tool has engaged correctly by
pulling it.
7.1.3 Removing the insert tool 5
1. Disconnect the supply cord plug from the power
outlet.
2. Open the chuck by pulling back the chuck release
sleeve.
3. Pull the insert tool out of the chuck.
7.2 Operation
CAUTION
Working on the material may cause it to splinter. Wear
eye protection and protective gloves. Wear breathing
protection if no dust removal system is used. Splin-
tering material presents a risk of injury to the eyes and
body.
CAUTION
The work generates noise. Wear ear protectors. Expos-
ure to noise can cause hearing loss.
7.2.1 Working at low temperatures
NOTE
The hammering mechanism works only when the power
tool has reached a minimum operating temperature.
Bring the drill bit briefly into contact with the base material
while allowing the power tool to run under no load until the
minimum operating temperature is reached. If necessary,
repeat this procedure until the hammering mechanism
begins to operate.
7.2.2 Hammer drilling
1. Bring the side handle into the desired position and
check that it is fitted correctly and secured.
2. Plug the supply cord into the power outlet.
3. Position the power tool and drill bit at the point
where the hole is to be drilled.
4. Press the control switch slowly (drill at a low speed
until the drill bit centers itself in the hole).
5. Press the control switch fully to continue drilling with
full power.
6. Do not apply excessive pressure. This will not in-
crease the power tool’s hammering performance.
Lower pressure extends the life of the insert tool.
7. Reduce drilling speed shortly before breaking
throughinordertoavoidspalling.
7.2.3 Forward / reverse 6
CAUTION
Do not operate the forward / reverse switch while the
motor is running.
Move the forward/reverse switch to the “Forward” or
“Reverse” position.
8 Care and maintenance
CAUTION
Disconnect the mains plug from the power outlet.
8.1Careofinserttools
Clean off dirt and dust deposits adhering to the insert
tools and protect them from corrosion by wiping the
insert tools from time to time with an oil-soaked rag.
8.2 Care of the power tool
CAUTION
Keep the power tool, especially its grip surfaces,
clean and free from oil and grease. Do not use clean-
ing agents which contain silicone.
The outer casing of the power tool is made from impact-
resistant plastic. Sections of the grip are made from a
synthetic rubber material.
Never operate the power tool when the ventilation slots
are blocked. Clean the ventilation slots carefully using
a dry brush. Do not permit foreign objects to enter the
interior of the power tool. Clean the outside of the power
tool at regular intervals with a slightly damp cloth. Do
not use a spray, steam pressure cleaning equipment or
running water for cleaning. This may negatively affect the
electrical safety of the power tool.
8.3 Cleaning or replacing the dust shield
Clean the dust shield on the chuck with a dry, clean
cloth at regular intervals. Clean the sealing lip by wiping it
carefully and then grease it again lightly with Hilti grease.
It is essential that the dust shield is replaced if the sealing
lip is found to be damaged. Pull the chuck sleeve back,
hold it securely in this position and remove the dust
shield. Clean the area of the chuck in contact with dust
en
19
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

shield and then fit a new dust shield. Press it in firmly
until it engages.
8.4 Maintenance
WARNING
Repairs to the electrical section of the power tool may
be carried out only by trained electrical specialists.
Check all external parts of the power tool for damage
at regular intervals and check that all controls operate
faultlessly. Do not operate the power tool if parts are
damaged or when the controls do not function faultlessly.
If necessary, the power tool should be repaired by Hilti
Service.
8.5 Checking the power tool after care and
maintenance
After carrying out care and maintenance work on the
power tool, check that all protective and safety devices
are fitted and that they function faultlessly.
9 Troubleshooting
Fault Possible cause Remedy
The power tool doesn’t start. Interruption in the electric supply. Plug in another electric appliance and
check whether it works.
Supply cord or plug defective. Have this checked by a trained elec-
trical specialist and replaced if neces-
sary.
The control switch is defective. Have this checked by a trained elec-
trical specialist and replaced if neces-
sary.
Other electrical fault. Have this checked by a trained elec-
trical specialist.
The carbon brushes are worn. Have this checked by a trained elec-
trical specialist and replaced if neces-
sary.
No hammering action. The power tool is too cold. Allow the power tool to warm up to
the minimum operating temperature.
See section: 7.2.1 Working at low
temperatures
The power tool doesn’t achieve
full power. The extension cord’s conductor cross section is inadequate. Use an extension cord with an ad- equate conductor cross section.
(Please refer to the “Description” sec-
tion.)
The control switch is not pressed
fully. Press the control switch as far as it will go.
The drill bit can’t be released. The chuck is not pulled back fully. Pull the chuck back as far as it will go
and remove the insert tool.
The drill bit makes no progress. The forward/reverse switch is set to
reverse rotation. Set the forward/reverse switch to for- ward rotation.
10 Disposal
Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials
must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for
taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or
Hilti representative for further information.
en
20
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

For EC countries only
Disposal of electric tools together with household waste is not permissible.
In observance of the European Directive on waste electrical and electronic equipment and its imple-
mentation in accordance with national law, electrical appliances that have reached the end of their life
must be collected separately and returned to an environmentally compatible recycling facility.
11 Manufacturer’s warranty - tools
Hilti warrants that the tool supplied is free of defects in
materialandworkmanship.Thiswarrantyisvalidsolong
as the tool is operated and handled correctly, cleaned
and serviced properly and in accordance with the Hilti
Operating Instructions, and the technical system is main-
tained. This means that only original Hilti consumables,
components and spare parts may be used in the tool.
This warranty provides the free-of-charge repair or re-
placement of defective parts only over the entire lifespan
of the tool. Parts requiring repair or replacement as a
result of normal wear and tear are not covered by this
warranty.
Additional claims are excluded, unless stringent na-
tional rules prohibit such exclusion. In particular, Hilti
is not obligated for direct, indirect, incidental or con-
sequential damages, losses or expenses in connec-
tion with, or by reason of, the use of, or inability to
use the tool for any purpose. Implied warranties of
merchantability or fitness for a particular purpose are
specifically excluded.
For repair or replacement, send the tool or related parts
immediately upon discovery of the defect to the address
of the local Hilti marketing organization provided.
This constitutes Hilti’s entire obligation with regard to
warranty and supersedes all prior or contemporaneous
comments and oral or written agreements concerning
warranties.
12 EC declaration of conformity (original)
Designation: Rotary hammer
Type: TE 1
Generation: 02
Year of design: 2008
We declare, on our sole responsibility, that this product
complies with the following directives and standards:
2004/108/EC, 2006/42/EC, 2011/65/EU, EN 60745‑1,
EN 60745‑2‑6, EN ISO 12100.
Hilti Corporation, Feldkircherstrasse 100,
FL‑9494 Schaan
Paolo Luccini Jan Doongaji
Head of BA Quality and Process Man-
agement
Executive Vice President
Business Area Electric Tools & Ac-
cessories
Business Unit Power
Tools & Accessories
01/2012 01/2012
Technical documentation filed at:
Hilti Entwicklungsgesellschaft mbH
Zulassung Elektrowerkzeuge
Hiltistrasse 6
86916 Kaufering
Deutschland
en
21
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00

*238043*
238043
Hilti Corporation
LI-9494 Schaan
Tel.: +423 / 234 21 11
Fax:+423 / 234 29 65
www.hilti.com
Hilti = registered trademark of Hilti Corp., Schaan
W 3506 | 0313 | 00-Pos. 1 | 1
Printed in China © 2013
Right of technical and programme changes reserved S. E. & O.238043 / A2
Printed: 07.07.2013 | Doc-Nr: PUB / 5138946 / 000 / 00