Hitachi SP18VA Manual

POWER TOOLS
TECHNICAL DATA
AND
SERVICE MANUAL
ELECTRONIC SANDER POLISHER
SP 18VA
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
LIST No. 0352 Jun. 2002
S
MODEL
SP 18VA

REMARK:
Throughout this TECHNICAL DATA AND SERVICE MANUAL, a symbol(s)
is(are) used in the place of company name(s) and model name(s) of our
competitor(s). The symbol(s) utilized here is(are) as follows:
Symbol Utilized
Competitor
Company Name Model Name
MAKITA 9227C/9227CB
C

Page
CONTENTS
1. PRODUCT NAME ........................................................................................................................... 1
2. MARKETING OBJECTIVE ............................................................................................................. 1
3. APPLICATIONS .............................................................................................................................. 1
4. SELLING POINTS .......................................................................................................................... 1
4-1. Selling Point Descriptions ............................................................................................................... 2
5. SPECIFICATIONS .......................................................................................................................... 3
6. COMPARISONS WITH SIMILAR PRODUCTS .............................................................................. 4
6-1. Specification Comparisons ............................................................................................................. 4
6-2. Practical Test Data .......................................................................................................................... 5
7. PRECAUTIONS IN SALES PROMOTION ..................................................................................... 6
7-1. Handling Instructions ...................................................................................................................... 6
7-2. Caution on Name Plate ................................................................................................................... 6
7-3. Precautions on Usage .................................................................................................................... 6
8. FUNCTION AND OPERATION OF THE CONTROL CIRCUIT ...................................................... 7
8-1. Control Circuit (Block Diagram) ...................................................................................................... 7
8-2. Function of Each Block ................................................................................................................... 7
8-3. Motor Characteristics and Voltage Applied to the Motor ................................................................. 8
9. PRECAUTIONS IN DISASSEMBLY AND REASSEMBLY ............................................................ 9
9-1. Disassembly of the Armature Ass'y ................................................................................................. 9
9-2. Disassembly of the Stator Ass'y.................................................................................................... 10
9-3. Disassembly of the Gear .............................................................................................................. 10
9-4. Reassembly ................................................................................................................................... 11
9-5. Tightening Torque .......................................................................................................................... 11
9-6. Wiring Diagram .............................................................................................................................. 11
9-7. Insulation Tests ............................................................................................................................. 12
9-8. Gear Backlash Value ................................................................................................................... 12
9-9. No-Load Current Value ................................................................................................................. 12
10. STANDARD REPAIR TIME (UNIT) SCHEDULES ..................................................................... 13
Assembly Diagram for SP 18VA

--- 1 ---
1. PRODUCT NAME
Hitachi Electronic Sander Polisher, Model SP 18VA [180 mm (7")]
2. MARKETING OBJECTIVE
The Model SP 18VA has been developed to upgrade and replace the current Model SP 18V. The main
improvements are increased motor power, weight reduction and improved operability.
3. APPLICATIONS
Sanding metallic surfaces.
Preparatory sanding and removing rust from metallic surfaces prior to painting, and removing paint prior to
repainting.
Finishing woodwork and making flush joints of wooden plates.
Preparatory sanding wooden surfaces prior to painting.
Finishing and polishing painted metallic surfaces of motor vehicles, rolling stocks, elevators, refrigerators,
sewing machines, washing machines, medical instruments, and so on.
Polishing lacquered surfaces on wooden products such as furniture.
Polishing synthetic resin and ebonite products.
4. SELLING POINTS
Compact body: 415 mm (10-19/36")
Maker C's model: 423 mm (10-3/4")
Variable trigger switch
Iron bearing bushing improves heat
resistance of the bearing chamber on
the commutator side.
Lightweight: 2.8 kg (6.2 lbs.)
Maker C's model: 3.0 kg (6.6 lbs.)
Loop handle
Equipped with electronic control devices
Constant speed control
Soft start speed control
Variable speed control
High-power motor,
max. output 2,200 W (2.9 HP)
Maker C's model: 1,900 W (2.5 HP)

--- 2 ---
4-1. Selling Point Descriptions
1) High-power motor and light weight
The Model SP 18VA is equipped with high-power motor and is more powerful than the current Model SP 18V
although it is compact and lightweight. We could say that the ratio of the motor's maximum output to the
product's weight defines its performance. Compared with a typical competitor's model in terms of this
indicator, the Model SP 18VA proves to have the highest performance.
Table 1 Comparison of max. output and product weight
Item
Maker
Model
914 (0.55 HP/lbs.)
Hitachi
2,560 (3.4 HP)
SP 18VA SP 18V
Max output *1(W)
Max output/product weight (W/kg)
Actual product weight *2(kg) 2.8 (6.2 lbs.)
567 (0.35 HP/lbs.)
1,700 (2.3 HP)
3.0 (6.6 lbs.)
633 (0.38 HP/lbs.)
1,900 (2.5 HP)
3.0 (6.6 lbs.)
C
*1 Max. output may vary depending on the market.
*2 Actual product weight is a measured weight and excludes cord, loop handle, rubber pad and washer nut.
2) Iron bearing bushing
An iron bearing bushing is newly added to the housing. The heat resistance of the bearing chamber on the
commutator side is significantly improved in comparison with current models.
Fig. 2
Ball bearing chamber of housing
Ball bearing
Bearing bushing (iron)
Rubber ring
Ball bearing
Ball bearing chamber of housing
New ball bearing chamber
of housing (SP 18VA)
Current ball bearing chamber
of housing (SP 18V)

--- 3 ---
5. SPECIFICATIONS
Item
Model SP 18VA
180 mm (7")Capacity disc dia.
AC single phase 50 or 60 Hz
Power source
Voltage (V)
Voltage, current and input
110
230
240
Current (A)
12.0
5.7
5.5
Input (W)
0 to 600/3,400 /minRotation speed (no-load)
AC single-phase commutator motorType of motor
Trigger switchType of switch
Material: Housing ••••• Glassfiber reinforced polyamide resin (green)
Handle ••••• Glassfiber reinforced polyamide resin (black)
Gear cover
Packing gland
Enclosure
2.8 kg (6.2 lbs.)
Net*
5.5 kg (12.2 lbs.)
Gross
Corrugated cardboard box
Packaging
Rubber pad ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 1
Loop handle••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 1
Wrench•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 1
Standard accessories
* Weight excludes cord, loop handle, rubber pad and washer nut.
Weight
220 6.0
120 11.0
1,250
••••• Aluminum alloy die casting
Coating: Gear cover
Packing gland ••••• Metallic silver
Relationship between dial settings and rotation speeds of the Model SP 18VA
4,000
3,000
2,000
1,000
1 2 3 4 5 6
Dial

--- 4 ---
6. COMPARISONS WITH SIMILAR PRODUCTS
6-1. Specification Comparisons
Maker HITACHI
Model SP 18VA
Capacity disc dia. 180 (7")
mm
Input 1,250
Output*1680
Max. output*12,560
Rotation speed (no-load) 0 ---600/3,400
Variable speed control
Handle type Loop handle
Dimensions
126 (3-7/36")
h81 (2-1/18")
L415 (10-19/36")
Weight*22.8 (6.2 lbs.)
2.8 (6.2 lbs.)
W
W
W
/min.
mm
mm
mm
kg
H
SP 18V
1,100
407
1,700
1,400 --- 3,400
Side handle
128 (3-1/4")
82 (2-1/12")
417 (10-7/12")
3.0 (6.6 lbs.)
3.0 (6.6 lbs.)
C
1,200
555
1,900
0 ---600/3,000
Loop handle
134 (3-5/12")
88 (2-2/9")
423 (10-3/4")
3.0 (6.6 lbs.)
3.0 (6.6 lbs.)
h
L
H
*1Output may vary depending on the market.
*2Weight excludes cord, loop handle, rubber
pad and washer nut.
180 (7") 180 (7")
Dial and trigger switch Dial Dial and trigger switch
Overload protection control None Equipped None
No-load sound pressure level 84 86 83
dB/A
Spindle lock Equipped Equipped Equipped
Catalog
Actual kg

--- 5 ---
6-2. Practical Test Data
1) Comparisons in torque vs. rotation speed
2) Sanding performance comparisons
SP 18V (maximum speed)
C (minimum speed)
C (maximum speed)
SP 18VA (minimum speed)
Torque (N•m)
12345
Rotation speed of spindle (1/min.)
500
1000
1500
2000
2500
3000
3500
0
Sanding dust produced (g)
50
100
150
200
250
300
350
0
SP 18VA
C
SP 18V
Time (min.)
Workpiece material: SPCC (mild steel)
Sanding disc used: AP #50
Applied pressure: 4 kg
Speed: Maximum speed
SP 18VA (maximum speed)
SP 18V (minimum speed)
51015

--- 6 ---
7. PRECAUTIONS IN SALES PROMOTION
In the interest of promoting the safest and most efficient use of the Model SP 18V Electronic Sander Polisher by
all of our customers, it is very important that at the time of sale the salesperson carefully ensures that the buyer
seriously recognizes the importance of the contents of the Handling Instructions, and fully understands the
meaning of the precautions listed on the Caution Plate attached to each tool.
7-1. Handling Instructions
Although every effort is made in each step of design, manufacture and inspection to provide protection against
safety hazards, the dangers inherent in the use of any electric tool cannot be completely eliminated. Accordingly,
general precautions and suggestions for the use of electric power tools, and specific precautions and suggestions
for the use of the Electronic Sander Polisher are listed in the Handling Instructions to enhance the safe and
efficient use of the tool by the customer. Salespersons must be thoroughly familiar with the contents of the
Handling Instructions to be able to offer appropriate guidance to the customer during sales promotion.
7-2. Caution on Name Plate
Each tool is provided with a Name Plate which contains the following basic safety precautions in the use of the
tool.
(2) For U.S.A. and Canada
(1) For Australia, New Zealand and China
(3) For Switzerland, U.K., Germany, Belgium, France, Netherlands, Austria, Spain,
Italy, Finland, Denmark and Norway
7-3. Precautions on Usage
Never press the pushing button while the spindle is rotating:
If the pushing button is pressed while the spindle is rotating, the spindle will stop immediately. In such a case,
there is a danger that the washer nut may be loosened so that the rubber pad and wool bonnet fly off
unexpectedly to cause possible serious injury.

--- 7 ---
8. FUNCTION AND OPERATION OF THE CONTROL CIRCUIT
8-1. Control Circuit (Block Diagram)
8-2. Function of Each Block
(1) Rotation speed detector:
Generates a frequency signal proportionate to the actual rotation speed of the motor. A magnetic sensor in the
controller monitors changes in the magnetic flux from a magnet, and generates a frequency signal.
(2) F-V converter:
Converts the frequency signal produced by the rotation speed detector into DC voltage.
(3) Standard voltage circuit:
Generates a standard voltage which determines the no-load rotation speed of the motor and serves as a
reference in maintaining constant rotation speed even when there are fluctuations in the load.
(4) Ramp generator:
Generates the voltage which determines the acceleration of the motor. The soft start function when the motor
is turned on is achieved through a gradual increase of the voltage generated by this circuit. When fully
charged, the voltage of the ramp generator becomes equal to the standard voltage (above).
(5) Differential amplifier:
Compares the voltage from the ramp generator voltages received from the F-V converter (which is
proportionate to the actual motor rotation speed), and amplifies the result.
This circuit functions as follows to maintain a constant rotation speed:
Motor rotation speed decreases (or increases) frequency signal decreases
(or increases) output voltage of the F-V converter decreases (or increases)
output voltage of the differential amplifier increases (or decreases).
Rotation speed
detector
Phase control circuit
Load current control circuit
Load current detecting circuit
Ramp generator Differential
amplifier
Variable resistor
F-V converter
Standard voltage
circuit
Soft start and constant speed control circuit
TriacMotorSwitch
AC power source

--- 8 ---
(6) Load current detecting circuit:
Detects the load current by means of a low resistance resistor which is in series with the motor and the triac.
(7) Load current control circuit:
When the detected load is excessive (overload), this circuit sends a command (control signal) to reduce power
to the motor.
(8) Phase control circuit:
Generates the trigger signals necessary to turn the triac on, and delivers them to the gate of the triac. The
conductive angle of the triac is determined by the timing of the generated trigger signals.
When starting the tool: Controlled by the soft start circuit, the phase control circuit generates trigger signals
to gradually increase the conductive angle of the triac.
Constant speed operation: When there are variations in the rotation speed, the phase control circuit
generates trigger signals to keep the rotation speed as close as possible to the
present rotation speed determined by the standard voltage circuit. In short, when
the load increases and causes the rotation speed to decrease, the conductive
angle of the triac is increases, and the voltage applied to the motor is increased.
In this way, the rotation speed is kept as close as possible to the standard
rotation speed.
8-3. Motor Characteristics and Voltage Applied to the Motor
Phase control voltage waveform
Conductive
angle
(When electronic control
not applied)
Rotation speed
determined by
the standard
voltage circuit
As the load inceases,
the voltage applied to the
motor increases.
Soft start characteristics
when starting the tool
Voltage applied to
the motor increases
gradually
Switch ON Time
Rotation speed
Dial
6
Rotation speed
0 No-load Load
Dial
Dial

--- 9 ---
9. PRECAUTIONS IN DISASSEMBLY AND REASSEMBLY
The [Bold] numbers in the descriptions below correspond to the item numbers in the Parts List and exploded
assembly diagram for the Model SP 18VA.
9-1. Disassembly of the Armature Ass'y
(1) Loosen the two Brush Caps [45], and take out the Carbon Brushes [46].
(2) Remove the four Tapping Screws (W/Flange) D5 x 30 [2]. The Armature Ass'y [13] can then be taken out
simultaneously with the Gear Cover Ass'y [5], Packing Gland [30] and related parts.
(3) Remove the four Seal Lock Screws (W/Sp. Washer) M5 x 14 (Black) [31], and remove the Packing Gland [30],
and related parts.
(4) After removing the three Seal Lock Screws (W/Sp. Washer) M4 x 10 [1], the Armature Ass'y [13] can be
extracted together with the Bearing Cover (B) [12], and related parts.
(5) Carefully wrap the Armature Ass'y [13] with a soft, clean rag to protect it from being damaged, and clamp it
securely in a vise. Remove the Retaining Ring for D8 Shaft.
(6) As illustrated in Fig. 3, the Ball Bearing 6200DDCMPS2L [9] can be removed from the Armature Ass'y [13] by
utilizing a J-204 Bearing Puller (special repair tool, Code No. 970982).
After the Ball Bearing has been removed, Bearing Cover (B) [12] can be easily taken off.
Fig. 3
Push
J-204 bearing puller
(Code No. 970982)

--- 10 ---
9-2. Disassembly of the Stator Ass'y
(1) After taking out the Armature Ass'y [13], loosen the four Tapping Screws (W/Flange) D5 x 20 (Black) [51], and
the two Tapping Screws (W/Flange) D4 x 20 (Black) [52] and remove Handle (A) [50] and Handle (B) [49].
(2) Disconnect the lead wires of the Stator Ass'y [16] from the Controller Switch [42].
(3) Disconnect the Brush Terminal [17] from the Brush Holders [47] and take out the Bearing Bushing [41].
(4) Finally, loosen the two Hex. Hd. Tapping Screws D5 x 60 [15], and the Stator Ass'y [16] can be taken out of
the Housing Ass'y [35]. If the Stator Ass'y [16] cannot be easily taken out of the Housing Ass'y [35],
disassembly can be facilitated by heating the Housing Ass'y to a temperature of approximately 60˚C (140˚F)
with an appropriate heating device.
J-278 gear puller
(Code No. 315635)
J-130 sleeve
(Code No. 970907)
Fig. 4
9-3. Disassembly of the Gear
(1) Loosen the four Seal Lock Screws (W/Sp. Washer) M5 x 14 (Black) [31], and remove the Packing Gland [30]
together with the Spindle [27] and the Gear [22] from the Gear Cover Ass'y [5] as a unit.
(2) When it is necessary to remove the Gear [22] from the Spindle [27], it is highly recommended that the special
repair tools described below be utilized.
As illustrated in Fig. 4, support the
angled surface of the Gear [22] with a
J-278 Gear Puller (special repair tool,
Code No. 315635), rest the J-278 Gear
Puller on the J-130 Sleeve (special
repair tool, Code No. 970907), and
push down on the tip of the Spindle
[27] with a hand press to remove the
Gear [22].
Push

--- 11 ---
9-4. Reassembly
Perform reassembly in the reverse order of disassembly while observing the given precautions and taking care of
the following points.
(1) After disassembly, thoroughly remove old grease from the inside of the Gear Cover Ass'y [5], and insert 25 g
of new grease (Nippeco JF-375, Code No. 930036, is recommended.) prior to reassembly. When inserting
grease, apply it to the pinion gear teeth surfaces, and to the needle bearing inside the gear cover.
(2) When replacing the ball bearing on the commutator side of the Armature Ass'y [13], be very careful to ensure
that the Dust Seal [34] is assembled in the proper direction. The Dust Seal [34] plays an important role in
dustproofing of the ball bearing, and must be replaced with a new one if disassembled.
(3) Apply Three Bond TB 1406 Screw Locking Agent to the following screws.
Three Seal Lock Screws (W/Sp. Washer) M4 x 10 [1] which fix Bearing Cover (B) [12] in place.
Three Seal Lock Screws (W/Sp. Washer) M4 x 10 [23] which fix Bearing Cover (A) [24] in place.
Four Seal Lock Screws (W/Sp. Washer) M5 x 14 (Black) [31] which fix Packing Gland [30] in place.
9-5. Tightening Torque
D4 Tapping Screws (W/Flange) [53],[52],[43] ••••••••••••••••••••••• 2.0 0.5 N •m (20 5 kgf •cm, 1.5 0.4 ft-lbs.)
D5 Tapping Screws (W/Flange) [51] [2]
D5 Hex. Hd. Tapping Screw [15]
M4 Seal Lock Screw (W/Sp. Washer) [23], [1]••••••••••••••••••••••••• 1.8 0.4 N •m (18 4 kgf •cm, 1.3 0.3 ft-lbs.)
M5 Seal Lock Screw (W/Sp. Washer) [31] •••••••••••••••••••••••••••••• 3.4 0.7 N •m (35 7 kgf •cm, 2.5 0.5 ft-lbs.)
•••••••••••••••••••••••••••••• 2.9 0.5 N •m (30 5 kgf •cm, 2.2 0.4 ft-lbs.)
9-6. Wiring Diagram
Armature
Ass'y [13]
White
or blue
White
or blue
Stator Ass'y [16]
Controller Switch [42]
Black or brown
Cord [56]
White or blue

--- 12 ---
9-7. Insulation Tests
On completion of disassembly after repair, measure the insulation resistance and conduct the dielectric strength
test.
Insulation resistance: 10 M or more with DC 500V megohm tester
Dielectric strength test: AC 4,400 V for 1 minute, with no abnormalities •••••••••••••• 220 V --- 240 V
AC 3,000 V for 1 minute, with no abnormalities •••••••••••••• 110 V ---120 V
9-8. Gear Backlash Value
Gear blacklash should be maintained at a value of 2 mm or less measured at the outer edge of a fresh depressed
center wheel.
9-9. No-Load Current Value
After no-load operation for 30 minutes, the no-load current value should be as follows.
Voltage (V)
Current (A) max.
220 230 240
3.9 3.9 3.9
110
6.8
120
6.8

--- 13 ---
10. STANDARD REPAIR TIME (UNIT) SCHEDULES
MODEL 10 20 30 40 50 60 min.
Fixed
Variable
SP 18VA Work Flow
Handle (B)
Housing Ass'y
Stator Ass'y
Handle (A)
Control Switch
Cord
Armature Ass'y
Gear Cover
Ass'y
Ball Bearing
(6200DD)
Ball Bearing
(608VV)
Dust Seal
Felt Packing (B)
General Assembly
Needle Bearing
Seal Packing
Lock Pin
Gear Ball Bearing
(6202DD)
Spindle
Felt Packing (A)
Packing Gland

ELECTRIC TOOL PARTS LIST
LIST NO.
ELECTRONIC SANDER POLISHER
Model SP 18VA
2002
•
6
•
20
(E1)
0352
123
45
678910 11 12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38 39 40
41
42 43
46 47 48
49
50
52
53
54
55
56
501 502 503 504 505
506
507
44
45
51

*ALTERNATIVE PARTS
ITEM
NO. CODE NO. DESCRIPTION REMARKS
NO.
USED
PARTS
6 -- 02
SP 18VA
1 303-255 SEAL LOCK SCREW (W/SP. WASHER) M4X10 3
2 305-507 TAPPING SCREW (W/FLANGE) D5X30 4
3 306-888 PUSHING BUTTON 1
4 306-889 SPRING 1
5 320-936 GEAR COVER ASS’Y 1 INCLUD.3,4,18-21
6 315-055 SEAL RING (A) 1
7 315-054 WASHER (A) 1
8 939-540
RETAINING RING FOR D10 SHAFT (10 PCS.) 1
9 620-0DD BALL BEARING 6200DDCMPS2L 1
10 315-053 RUBBER RING (A) 1
11 315-052 FELT PACKING (B) 1
12 315-051 BEARING COVER (B) 1
* 13 360-576U ARMATURE ASS’Y 110V-120V 1 INCLUD.9,11,34,38
* 13 360-576E ARMATURE 220V-240V 1
14 315-046 FAN GUIDE 1
15 961-501 HEX. HD. TAPPING SCREW D5X60 2
* 16 340-526C STATOR ASS’Y 110V 1 INCLUD.17
* 16 340-526D STATOR ASS’Y 120V 1 INCLUD.17
* 16 340-526E STATOR ASS’Y 220V-240V 1 INCLUD.17
17 930-703 BRUSH TERMINAL 2
18 315-049 FELT WASHER 1
19 320-218 O-RING 1
20 315-050 LOCK PIN 1
21 871-397 NEEDLE BEARING (NTN HK1210) 1
22 320-937 GEAR 1
23 987-201
SEAL LOCK SCREW (W/SP. WASHER) M4X10 3
24 937-077 BEARING COVER (A) 1
25 620-2DD BALL BEARING 6202DDCMPS2L 1
26 940-533 FEATHER KEY 3X3X10 1
* 27 320-943 SPINDLE 1
* 27 320-944 SPINDLE 1 FOR USA,CAN
28 315-062 FELT PACKING (A) 1
29 315-060 SEAL PACKING 1
30 315-061 PACKING GLAND 1
31 315-636
SEAL LOCK SCREW (W/SP.WASHER)M5X14(BLACK) 4
* 32 953-255 RUBBER PAD (D16 HOLE) 1
* 32 953-247Z RUBBER PAD (D14 HOLE) 1 FOR USA,CAN
* 33 953-246Z WASHER NUT M14 1
* 33 953-254P WASHER NUT 5/8”-11UNC 1 FOR USA,CAN
34 315-047 DUST SEAL 1
35 320-945 HOUSING ASS’Y 1 INCLUD.39,41,47,48
36 320-948 SETTING LABEL 1
* 37 NAME PLATE 1
38 608-VVM BALL BEARING 608VVC2PS2L 1
39 995-662 RUBBER RING 1
40 318-721 MAGNET 1
41 320-946 BEARING BUSHING 1
* 42 320-941 CONTROLLER SWITCH 1
* 42 320-940 CONTROLLER SWITCH 1 FOR GBR (110V),USA,CAN
43 305-095 TAPPING SCREW (W/FLANGE) D4X20 2
44 HITACHI LABEL 1

*ALTERNATIVE PARTS
ITEM
NO. CODE NO. DESCRIPTION REMARKS
NO.
USED
PARTS
6 -- 02
SP 18VA
45 945-161 BRUSH CAP 2
46 999-043 CARBON BRUSH (1 PAIR) 2
47 958-900 BRUSH HOLDER 2
48 938-477 HEX. SOCKET SET SCREW M5X8 2
49 320-939 HANDLE (B) 1
50 320-938 HANDLE (A) 1
51 302-089 TAPPING SCREW (W/FLANGE) D5X20 (BLACK) 4
52 302-086 TAPPING SCREW (W/FLANGE) D4X20 (BLACK) 2
53 984-750 TAPPING SCREW (W/FLANGE) D4X16 2
54 937-631 CORD CLIP 1
55 953-327 CORD ARMOR D8.8 1
* 56 500-234Z CORD 1 (CORD ARMOR D8.8)
* 56 500-435Z CORD 1
(CORD ARMOR D8.8) FOR HKG,GBR (230V)
* 56 500-439Z CORD 1 (CORD ARMOR D8.8) FOR NZL,AUS
* 56 500-396Z CORD 1 (CORD ARMOR D8.8) FOR GBR (110V)
* 56 500-247Z CORD 1
(CORD ARMOR D8.8) FOR NOR,SWE,DEN,FIN
* 56 500-447Z CORD 1 (CORD ARMOR D8.8) FOR SUI
* 56 500-241Z CORD 1 (CORD ARMOR D8.8) FOR USA,CAN

*ALTERNATIVE PARTS6 -- 02
ITEM
NO. CODE NO. DESCRIPTION REMARKS
NO.
USED
SP 18VA
OPTIONAL ACCESSORIES
STANDARD ACCESSORIES
ITEM
NO. CODE NO. DESCRIPTION REMARKS
NO.
USED
Printed in Japan
(020620N)
501 955-857 HEX. BAR WRENCH 8MM 1
502 937-913Z WRENCH 1
503 320-949 LOOP HANDLE 1
504 949-434 BOLT WASHER M10 (10 PCS.) 2
505 949-844 HEX. SOCKET HD. BOLT M10X20 (10 PCS.) 2
* 506 949-103 WOOL BONNET 180MM 1 EXCEPT FOR FRA,SUI,USA,CAN
* 507 314-090 SANDING DISCS 180MM C-P50 (10 PCS.) 1 EXCEPT FOR FRA,SUI,USA,CAN
601 314-084 SANDING DISCS 180MM C-P16 (10 PCS.) 1
602 314-085 SANDING DISCS 180MM C-P20 (10 PCS.) 1
603 314-086 SANDING DISCS 180MM C-P24 (10 PCS.) 1
604 314-088 SANDING DISCS 180MM C-P36 (10 PCS.) 1
605 314-089 SANDING DISCS 180MM C-P40 (10 PCS.) 1
606 314-090 SANDING DISCS 180MM C-P50 (10 PCS.) 1
607 314-091 SANDING DISCS 180MM C-P60 (10 PCS.) 1
608 314-093 SANDING DISCS 180MM C-P100 (10 PCS.) 1
* 609 949-103 WOOL BONNET 180MM 1 FOR FRA,SUI,USA,CAN
610 994-322 SIDE HANDLE 1