Holis HOLNVR08 Series User manual

Network Video Recorder
HOLNVR08xxx
HOLNVR08xxx8P
Quick Start Guide
8200-1104-02 B0

i
Notice
Please read this manual thoroughly and save it for future use before attempting to connect or operate
this unit.
The information in this manual was current when published. The manufacturer reserves the right to
revise and improve its products. All specifications are therefore subject to change without notice.
Copyright
Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine-readable form, in whole or in part, without
prior written consent of Tyco Security Products. © 2015 Tyco Security Products. All rights reserved.
Customer Service
Thank you for using Tyco Security Products. We support our products through an extensive worldwide
network of dealers. The dealer through whom you originally purchased this product is your point of
contact if you need service or support. Our dealers are empowered to provide the very best in
customer service and support. Dealers should contact Tyco Security Products at [phone] or
[phone] or on the Web at www.holisnvr.com
Trademarks
The trademarks, logos, and service marks displayed on this document are registered in the United
States [or other countries]. Any misuse of the trademarks is strictly prohibited and Tyco Security
Products. will aggressively enforce its intellectual property rights to the fullest extent of the law,
including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco
Security Products. are the property of their respective owners, and are used with permission or allowed
under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary
from photos. Not all products include all features. Availability varies by region; contact your sales
representative.
Sensormatic Electronics LLC
6600 Congress Avenue
Boca Raton,
FL33487
U.S.A.

ii
Table of Contents
Important Safeguards and Warnings......................................................................................................iii
Hardware Installation and Connection....................................................................................................1
Check Unpacked NVR ...................................................................................................................1
About Front Panel and Rear Panel ................................................................................................1
After Remove the Chassis..............................................................................................................1
HDD Installation..............................................................................................................................1
Front Panel.....................................................................................................................................3
Rear Panel......................................................................................................................................5
Connection Sample.................................................................................................................................7
GUI Operation.........................................................................................................................................8
Login...............................................................................................................................................8
Remote Device...............................................................................................................................9
Schedule.......................................................................................................................................11
Real time Playback.......................................................................................................................13
Preview control interface .....................................................................................................13
Web Operation......................................................................................................................................15
Network Connection ............................................................................................................15
About PoE address setup, operation and allocation................................................................15
Login....................................................................................................................................16
Main Window .......................................................................................................................17
LAN Login ................................................................................................................................17
WAN Login...............................................................................................................................17
Appendix Toxic or Hazardous Materials or Elements..................................................................18

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Keep upwards. Handle with care.
Do not apply power to the NVR before completing installation.
Do not place objects on the NVR
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
The NVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive
substances and etc.
This series product shall be transported, storage and used in the specified environments.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Lithium battery
Improper battery use may result in fire, explosion, or personal injury!
When replace the battery, please make sure you are using the same model!
Before your operation please read the following instructions carefully.
Installation environment
Keep away from extreme hot places and sources；
Avoid direct sunlight；
Keep away from extreme humid places；
Avoid violent vibration；

iv
Do not put other devices on the top of the NVR；
Be installed in well ventilated place; do not block the vent.
Accessories
Check the accessories after opening the box：
Please refer to the packing list in the box *

1
Hardware Installation and Connection
Note
All the installation and operations should conform to your local electric safety rules.
Check Unpacked NVR
When you receive the NVR from the forwarding agent, please check whether there is any visible damage.
The protective materials used for the package of the NVR can protect most accidental clashes during
transportation. Then you can open the box to check the accessories.
Please check the items in accordance with the list (Remote control is optional). Finally you can remove the
protective film of the NVR.
About Front Panel and Rear Panel
For detailed information of the function keys in the front panel and the ports in the rear panel, please refer to
the User Manual included in the resource CD.
The model label in the front panel is very important; please check according to your purchase order.
The label in the rear panel is very important too. Usually we need you to represent the serial number when
we provide the service after sales.
After Remove the Chassis
Please check the data cable, power cable, COM cable and main boar cable connection is secure or not.
HDD Installation
CAUTION
Please turn off the power before you replace the HDD.
The pictures listed below for reference only
You can refer to the User Manual for recommended HDD brand. Please use HDD of 7200rpm or higher.
Usually we do not recommend the PC HDD.
For detailed operation instruction, please refer to the User Manual included in the resources CD.

2
1. Use the screwdriver to loose the screws of the rear panel and then remove the front cover.
2. Put the HDD to the HDD bracket in the chassis and then line up the four screws to the four holes in
the HDD. Use the screwdriver to fix the screws firmly to secure HDD on the HDD bracket
3. Connect to the HDD data cable to the main board and the HDD port respectively. Loosen the power
cable of the chassis and connect another end of the power cable to the HDD port.
4. After connect the cable, put the front cover back to the device and then fix screws of the rear panel.

3
Front Panel
For detailed operation instruction, please refer to the User’s Manual included in the resources CD.
The front panel is shown as in Figure .
Figure 1
Please refer to the following sheet for front panel button information.
Name
Icon
Function
Power button
Power button, press this button for three seconds to boot up or
shut down NVR.
Shift
Shift
In textbox, click this button to switch between numeral,
English(Small/Capitalized),donation and etc.
Up/1
Down/4
、
Activate current control, modify setup, and then move up and
down.
Increase/decrease numeral.
Assistant function such as PTZ menu.
In text mode, input number 1/4 (English character G/H/I)
Left/2
Right/3

Shift current activated control,
When playback, click these buttons to control playback bar.
In text mode, input number 2(English character A/B/C)
/3(English character D/E/F)
.
ESC
ESC
Go to previous menu, or cancel current operation.
When playback, click it to restore real-time monitor mode.
Enter
ENTER
Confirm current operation
Go to default button
Go to menu
Record
REC
Manually stop/start recording, working with direction keys
or numeral keys to select the recording channel.
Slow play/8
Multiple slow play speeds or normal playback.
In text mode, input number 8 (English character T/U/V).
Assistant
Fn
One-window monitor mode, click this button to display assistant
function: PTZ control and image color.

4
Backspace function: in numeral control or text control, press it
for 1.5seconds to delete the previous character before the
cursor.
In motion detection setup, working with Fn and direction keys to
realize setup.
In text mode, click it to switch between numeral, English
character(small/capitalized) and etc.
Realize other special functions.
Fast play/7

Various fast speeds and normal playback.
In text mode, input number 7 (English character P/Q/R/S).
Play
previous/0
|
In playback mode, playback the previous video
In text mode, input number 0.
Reverse/Paus
e/6
||
In normal playback or pause mode, click this button to reverse
playback
In reverse playback, click this button to pause playback.
In text mode, input number 6 (English character M/N/O)
.
Play Next/9
|
In playback mode, playback the next video
In menu setup, go to down ward of the dropdown list.
In text mode, input number 9 (English character W/X/Y/Z)
.
Play/Pause /5
||
In normal playback click this button to pause playback
In pause mode, click this button to resume playback.
In text mode, input number 5(English character J/K/L).
USB port
To connect USB storage device, USB mouse.
Network
abnormal
indication light
Net
Network error occurs or there is no network connection, the
light becomes red to alert you.
HDD
abnormal
indication light
HDD
HDD error occurs or HDD capacity is below specified threshold
value, the light becomes red to alert you.
Record light
1-16
System is recording or not. It becomes on when system is
recording.
IR Receiver
IR
It is to receive the signal from the remote control.

5
Rear Panel
For detailed operation instruction, please refer to the User Manual included in the resources CD.
The rear panel is shown as below. See Figure 2.
Figure 2
Please refer to the following sheet for detailed information.
Name
Function
Power
switch
/
Power on/off button.
Power input
socket
/
Input AC 100~240V.
Power input port
Input DC 12V/5A.
Power input port
Switch power port. Input DC 48//1.04A.
MIC IN
Audio input port
Bidirectional talk input port. It is to receive the analog
audio signal output from the devices such as mike phone,
pickup.
MIC OUT
Audio output port
Audio output port. It is to output the analog audio signal
to the devices such as the sound box.
Bidirectional talk output.
Audio output on 1-window video monitor.
Audio output on 1-window video playback.
1～4
Alarm input port
1～4
There are two types; NO (normal open)/NC (normal
close).
When your alarm input device is using external
power, please make sure the device and the NVR
have the same ground.
GND
Alarm input ground port.
N1, N2
Alarm output port
1～2
2 groups of alarm output ports. (Group 1 ：port
NO1 ～C1,Group 2:port NO2 ～C2).Output alarm
signal to the alarm device. Please make sure there
is power to the external alarm device.
NO：Normal open alarm output port.
C：Alarm output public end.
C1, C2