Holman 40251 Manual

Holman
Rancho Cordova, CA 95742
800-343-7486
[e-mail]
20220331R1 DATE: ________________
Instruction Guide
40251

Instructions –40251
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 1
*PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
INSTALLING, AND USING THIS PRODUCT.*
Warning
Always check for wires, fuel tanks and lines, brake lines and other
important vehicle functionality items prior to drilling and installing all
products.
Tools Needed
7/16” Socket and Wrench
7/16”, 9/16” Box Wrench
25/64” Drill Bit
Drill
Drill Bit Stop Collar
Plus Nut Installation Tool (P9902)*
#2 Philips Head Screw Driver
* Sold Separately.
Table of Contents
Before You Begin ............................................................................................................................1
Parts................................................................................................................................................2
Hardware.........................................................................................................................................2
Step 1 –Remove Cover ..................................................................................................................3
Step 2 –Install Plus Nuts.................................................................................................................4
Step 3 –Install Drawer Assembly....................................................................................................5
Step 4 –Install Cover ......................................................................................................................5
Before You Begin
Read all instructions prior to assembling or installing any Holman product.
Always locate your installation locations prior to performing any work.
ENSURE SAFETY WHILE INSTALLING OR DRILLING INTO VEHICLE.
Plus Nut Installation Tool Kit (P9902) is not included and must be purchased separately.

Instructions –40251
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 2
Parts
Hardware

Instructions –40251
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 3
DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF.
Step 1 –Remove Cover
Remove screws in each side of cover and on top of cover.
Remove cover.

Instructions –40251
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 4
Step 2 –Install Plus Nuts
Place drawer assembly in installation position.
Mark onto the installation surface the location of the holes in bottom of both sides of assembly.
Remove assembly.
DO NOT drill beyond depth of floor or installation surface. Always check
for wires, fuel tanks and lines, brake lines and other important vehicle
functionality items prior to drilling and installing all products.
At each marked location, drill hole using 25/64” drill bit and appropriate sized drill-bit stop collar. If
25/64” drill bit is not available, a 3/8” drill bit can be used, although it may be necessary to tap in
the plus nuts.
Insert 1/4” x 2-1/4” hex head bolt through 1/4” flat washer and
plus nut installation tool, and then screw bolt into plus nut.
Knurled end of plus nut tool must be directed away from bolt
head and contacting plus nut.
Insert plus nut into hole with plus nut tool attached.

Instructions –40251
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 5
Using the 9/16” box wrench, hold the plus nut
tool stationary and then tighten hex head bolt
until plus nut is tightly gripping and does not
spin when hex bolt is loosened.
DO NOT overtighten plus nut.
Using the 9/16” box wrench, hold the plus nut
tool stationary to remove the 1/4” hex head bolt.
Step 3 –Install Drawer Assembly
Using six
1/4” x 1-1/4” hex
head bolts, 1/4” lock
washers, 1/4” flat
washers, and nylon
spacers, fasten the
drawer assembly to
the installed plus
nuts.
Step 4 –Install Cover
Replace cover on drawer assembly.
Using the screws previously removed in Step 1, reinstall cover.
GO BACK AND TIGHTEN ALL HARDWARE.
INSTALLATION IS COMPLETE.
HOLD