HOLOPHANE Parkpak Manual

1. INTRODUCTION
1.1 Product Description. The Parkpak luminaire is suitable
for use in wet locations and has been designed and tested to meet
UL standards.
- The Parkpak luminaire is used in both indoor and outdoor applica-
tions.
- The Parkpak is mounted in a variety of ways -- ceiling, horizontal,
vertical, pendant, flexible pendant, and quick install/through-wiring.
- Both square and asymmetric refractors provide excellent vertical
illumination.
1.2 Alternate Information Sources. If additional
questions arise relative to the Parkpak that this document or your
supplier cannot answer, please refer them to :
Holophane
Field Service Department
P.O. Box 3004
Newark, OH 43058-3004
866-759-1577
AFTER INSTALLATION DELIVER THIS
MANUAL TO OWNER
Parkpak
GR71
®Installation and
Maintenance
Manual
2. INSTALLATION
2.1 Tools and Materials Required.
Table 1. Installation Tools and Materials
Description Use
1/4 socket wrench Fasteners
7/16 socket wrench Fasteners
Flat screwdriver Fasteners
Phillips screwdriver Fasteners
Tamper resistant screwdriver Tamper resistant fasteners
(if applicable)
2.1.1 General Mounting Information. If this fixture is to
be surface mounted and connected to an outlet box, the luminaire
assembly must be connected to an outlet box marked for use in wet
locations and the mounting gasket provided must be used to create
a watertight seal between the luminaire assembly and the outlet box
or Latex caulk must be used to provide a watertight seal between
the luminaire assembly and the outlet box.
2.2 Horizontal Mount for Square Poles.
2.2.1 Remove the lens, door, and reflector. Remove the reflector
carefully in order to maintain the electrical connections between the
reflector and the housing. See Figure 1.
2.2.2 For the arm version, attach the arm to the pole and housing
to the arm using gaskets and fasteners as shown in Figure 2. For
the non-arm version, see Figure 3.
2.2.3 For supply connections, outside the housing, use wire rated
for at least 90 degree C. For supply connection inside the housing
use wire rated for at least 200 degree C. Connect supply leads to
marked leads on ballast or to the extra length leads provided with
the arm if applicable.
Figure 1
GR636A
IM-83-C
WARNING-READ THESE INSTRUCTIONS
CAREFULLYBEFORE ATTEMPTING TO INSTALL OR
MAINTAIN THIS FIXTURE. WORK MUST BE DONE
BY QUALIFIED PERSONNEL.
WARNING-BE CERTAIN THAT ALL ELECTRICAL
POWER IS DISCONNECTED FROM THE FIXTURE
BEFORE INSTALLING OR MAINTAINING THE FIXTURE.
WARNING-FOLLOW LAMP MANUFACTURER'S
OPERATING AND MAINTENANCE INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE WARNINGS MAY
RESULT IN DEATH, INJURY OR SIGNIFICANT
PROPERTY DAMAGE.
DISCONTINUED

2.2.4 Attach reflector to housing with four captive screws. Keep
the captive gasket in place and avoid pinching the wires. Insert
proper lamp type into socket.
2.2.5 Attach the door and lens to the housing using four captive
screws. For asymmetric distribution, orient the word "Front"
towards area to be lighted. Tighten the captive screws only until
the lens compresses the captive gasket. Do no overtighten
screws.
2.2.6 Figure 4 is a diagram of the hole pattern that must be on
either the pole or wall in order to install this fixture. Figure 5
GR635
GR633A
Figure 3
Figure 2
GR630
2.3 Horizontal Wall Mount.
2.3.1 Remove the lens and door. Remove the reflector carefully in
order to maintain the electrical connections between the reflector
and the housing. See Figure 1.
2.3.2 See Figure 5 for the hole pattern that must be on the wall in
order to attach this fixture.
GR632A
Figure 6
Figure 4
GR634
2.3.3 If using the wall bracket with the arm, discard the wedge
and attach arm, housing, gaskets and wall bracket as shown in
Figure 6. If using only the wall bracket, attach the housing, wedge,
gaskets and wall bracket as shown in Figure 7.
2.3.4 To finish follow steps 2.2.3 through 2.2.5.
DISCONTINUED

GR644
Figure 8
2.4 Vertical Mounting for Pole Application.
2.4.1 Remove the lens and the door. Remove the reflector
carefully in order to maintain the electrical connections between the
reflector and the housing. See Figure 1.
2.4.2 See Figure 8 for the hole pattern that must be on the pole in
order to install this fixture. Mount the housing to the pole using two
lockwashers and two 3/8-16 fasteners provided.
2.4.3 To finish follow steps 2.2.3 through 2.2.5.
Figure 7
GR645A
2.5 Ceiling Mounting.
2.5.1 Remove the lens and the door. Remove the reflector
carefully in order to maintain the electrical connections between the
reflector and the housing. See Figure 1.
2.5.2 Remove the two knockouts for 7/16 diameter mounting holes
and mount to ceiling. See Figure 8 for the hole pattern which must
be on the mating surface in order to attach this fixture.
2.5.3 Bring the supply wires through the center 15/16 diameter
hole. For supply connections outside the housing, use wire rated
for at least 90 degrees C. For supply connections inside the
housing, use wire rated for at least 200 degrees C. Connect supply
leads to marked leads on ballast.
2.5.4 To finish follow steps 2.2.4 through 2.2.5.
2.6 Quick Install/Through Wiring Mounting.
2.6.1 Set the fixture on the hooks of the ceiling cover (shipped
separate). Make up the supply wiring connections to the lighting
fixture. Hinge the fixture up and drive in captive screw provided.
The assembly is now locked together. See Figure 9.
2.6.2 Remove the lens to insert correct lamp type into socket.
2.6.3 Attach the lens to the housing using four captive screws.
For asymmetric distribution, orient the word "Front" toward the area
to be lighted. Tighten the captive screws only until the lens
compresses the captive gasket. Do not overtighten screws.
2.7 Pendant Mounting.
2.7.1 Remove the lens and the door. Remove the reflector
carefully in order to maintain the electrical connections between the
reflector and the housing. See Figure 1.
2.7.2 Mount the housing by threading rigid conduit into 3/4-14 NPT
tapped hole in top of the housing. Lock with locknut provided. Seal
threads with water tight sealant.
2.7.3 To finish follow steps 2.2.3 through 2.2.5.
2.8 Flexible Pendant Mounting.
2.8.1 Remove the top plate from the fixture. Thread plate onto 3/
4-14 NPT hook or loop and lock with set screw provided. Orient
plate to desired position of the fixture. Seal threads with water tight
sealant. See Figure 10.
2.8.2 For supply connections, outside the housing, use wire rated
for least 90 degree C. Splice wires inside well on plate on top of
housing. Reattach the top plate to the plate on the housing using
two washers and two 1/4-20 bolts provided. Slide top plate until
the fixture hangs level. Tighten bolts.
2.8.3 Remove the lens and insert proper lamp type into socket.
2.8.4 Attach the lens to the housing using four captive screws.
For asymmetric distribution, orient the word "Front" towards area to
be lighted. Tighten the captive screws only until the lens com-
presses the captive gasket. Do no overtighten screws.
Figure 9
GR637
DISCONTINUED

3. MAINTENANCE
3.1 Relamping and Cleaning.
3.1.1 Disconnect electrical power to the fixture. Wipe fixture free
of debris and dirt.
3.1.2 Remove the lens and door from the reflector. Remove the
lamp and discard it in a safe and legal manner. Wipe the reflector
and lens with a clean dry cloth to remove dust and dirt.
3.1.3 Install the correct new lamp type according to relamp
markings.
3.1.4 Reinstall the door and lens using the four captive screws.
Tighten the captive screws until the lens is compressing the captive
gasket. Do not overtighten screws.
3.2 Electrical Component Replacement.
3.2.1 Disconnect electrical power to the fixture.
3.2.2 Remove the lens and door from the reflector. Remove the
lamp and the reflector carefully.
3.2.3 Tag all wiring to be disconnected to assure proper rewiring.
3.2.4 Remove any electrical components that need to be replaced,
saving the attachment hardware. Note the orientation and position
of the electrical components before removing them to insure proper
positioning of the new component.
3.2.5 Position the new electrical component and attach them with
the original hardware. Be certain all fasteners are fully engaged
and/or tightened.
3.2.6 Rewire the electrical components according to the marked
tags and approved wiring practices. When completed, check all
wiring to insure that all connections are tight and no wires are
pinched.
3.2.7 Reinstall the reflector and lamp using the captive screws.
Make sure the lamp type agrees with relamp markings. Reinstall the
door and the lens using the captive screws. Tighten the captive
screws until the lens is compressing the captive gasket. Do not
overtighten screws.
3.2.8 Reconnect the electrical power and energize the fixture.
Check the fixture for proper operating.
4. Limited Warranty and Limitation of Liability
The Holophane limited warranty and limitation of liability is published
in the "Terms and Conditions" section of the current Holophane
buyer's guide, and is available from your local Holophane sales
representative.
2.9 Options
2.9.1 Emergency standby lighting is offered with this fixture. A
100 watt tungsten-halogen lamp is supplied with the fixture. The
emergency lamp socket is located on the reflector. Remove lens
and insert the emergency lamp. Install the door as described in step
2.2.5.
2.9.2 Factory installed fusing is offered also. The fixture is
marked with a label indicating fused fixture. Make appropriate
electrical connections.
2.9.3 Photocontrol is offered with all mountings. The photocontrol
is factory installed with photocell included. Orient photocell in a
northerly direction. Make appropriate electrical connections.
2.9.4 Tamper-resistant screws are offered for certain applica-
tions. These fasteners are factory installed. Holophane offers a
tamper-resistant driver which is ordered separately from the
fixture.
2.9.5 If using the external shield, make certain the fixture is
oriented correctly. Then remove the appropriate two (2) screws
which secure the lens to the housing. Attach the shield as shown
in Figure 1. Tighten the captive screws until the lens is compress-
ing the gasket. Do no overtighten.
Figure 10
GR638
Acuity Lighting Group, Inc.
214 Oakwood Ave., Newark, OH 43055
IM-83-C 1/03 2002 Acuity Lighting Group Inc.
Visit our web site at www.holophane.com
Printed in USA
®
DISCONTINUED