Holzhof MAX XM 100 R line User manual

MAX XM 100 R line
MAX XM 100 R line MAX XM 100 R line
MAX XM 100 R line
assembly
assembly assembly
assembly
instructions
instructionsinstructions
instructions

TIME SEQUENCE TO BE OLLOWED:
1. STRUTS AND PLAT ORMS 6. BENCH
2. ARCHWAYS 7. ROO
3. PARAPETS 8. UNDERGROUND LAYING/ANCHORAGE O THE STRUCTURE
4. SLIDE
5. CLIMBING BOARD

NOTA BENE: it is recommended to fix the bolts
definitively and only insert the caps once the
correct positioning of the elements has been
verified.
Article
num.
fixing
CODE N.
NAME
12
xpe11 Shaped PE nut protection cap
22
xpe10 PE nut protection cap
34
xpe116 PE cap
4
4
_
ISO7089 Ø8 washer
5
2
_
UNI7473 M8 self-locking nut
7 2
-
UNI4017 M8X155 HEX SCREW
NOTE:
-The colours and models in the
image are purely indicative.
-
The platform can be in engineered wood or
wooden planking.

NOTA BENE: it is recommended to fix the bolts definitively and only
insert the caps once the correct
positioning of the elements has been verified.
1. Position the archway between the struts and fix it by inserting: 1 x M8 washer (3), 1 x M8x260
TORX screw (2), 1 x Ø25 mm. winged PE cap (1) into the upper part;
1 x PE nut protection cap (4), 1 x M8 washer (3),
1 x M8x260 TORX screw (2), 1 x PE cap (5) into the lower part.
2. Repeat the operation for the opposite
side. ix the other archways.

NOTA BENE: it is recommended to fix
the bolts definitively and only insert the
caps once the correct positioning of the
elements has been verified.
1. Position the PE parapet between the
struts, resting the two lower fixing wings on
the platform and then fix using:
4 x M8 washer (3)
4 x M8x80 TEL screw (2) WOOD
4 x M6
,
3x60 TE R screw (2) ALUMINIUM
4 x Ø25 winged PE cap
2. If necessary, repeat the operation on the other parapets.

1. After having fixed the PE archway (2), place the body of the
curved slide (3) on the platform of the tower (1) and insert
the bolts, necessary for fixing, into the holes present on the
slide (3).
2. Check correct positioning, verticality and parallelism. ix
the bolts definitively and position the caps.
3. Repeat the operation also on the other side of
the slide.
NOTE: COLOURS AND MODELS
REPRESENTED ARE PURELY
INDICATIVE
Article
num.
Default/
Quantity
NAME
1 1 Aladin tower
2 1 Aladin PE archway
3 1 Curved slide h.84
4 4 IS07089 Ø8 washer
5 4 M8x180 TORX screw
6 4 PE cap

NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the elements
has been verified.
1.
1.1.
1. I
II
Insert the (5) M8x70 threaded bars into the
nsert the (5) M8x70 threaded bars into the nsert the (5) M8x70 threaded bars into the
nsert the (5) M8x70 threaded bars into the
bushes present on the (6) climbing board.
bushes present on the (6) climbing board.bushes present on the (6) climbing board.
bushes present on the (6) climbing board.
2.
2.2.
2. Attach the climbing board (6) by
Attach the climbing board (6) by Attach the climbing board (6) by
Attach the climbing board (6) by
introducing the threaded bars (5) into
introducing the threaded bars (5) into introducing the threaded bars (5) into
introducing the threaded bars (5) into
the pre
the prethe pre
the pre-
--
-drilled holes in the
drilled holes in thedrilled holes in the
drilled holes in the platform
platform platform
platform
frame; these were previously fixed by
frame; these were previously fixed by frame; these were previously fixed by
frame; these were previously fixed by
inserting the PE nut protection cap (4),
inserting the PE nut protection cap (4), inserting the PE nut protection cap (4),
inserting the PE nut protection cap (4),
M8 washer (3), M8 self
M8 washer (3), M8 selfM8 washer (3), M8 self
M8 washer (3), M8 self-
--
-locking nut and
locking nut and locking nut and
locking nut and
(2) and PE cap (1).
(2) and PE cap (1).(2) and PE cap (1).
(2) and PE cap (1).
1) 2 x PE cap
2) 2 x M8 self-locking nuts
3) 2 x M8 washer
4) 2 x PE nut protection cap
5) 2 x M8x70 LG* threaded bar
6) 2 x M8x50 AL* threaded bar
7) PE climbing board
*L : Wood
*AL: Aluminium

NOTE:
NOTE:NOTE:
NOTE:
The models represented are purely
The models represented are purely The models represented are purely
The models represented are purely
indicative.
indicative.indicative.
indicative.
These instructions are applicable to
These instructions are applicable toThese instructions are applicable to
These instructions are applicable to
Max, Sultan and Aladin roofs.
Max, Sultan and Aladin roofs.Max, Sultan and Aladin roofs.
Max, Sultan and Aladin roofs.
1. Position the roof on top of the struts with the brackets positioned
as in figure A.
2. Insert the bolts necessary for fixing in sequence, as indicated in
figure B.
3. Repeat the operation on all 4 struts.
BOLT POSITION
Article
num.
Default/
Quantity
CODE N.
NAME
1 1 - PE roof
2 4 xpe10 PE nut protection cap
3 4 xpe116 PE cap
4 4
_
IS07089 Ø8 washer
6 4
_
M8x80 TEL screw

1)
1)1)
1) PE cap (4x)
PE cap (4x)PE cap (4x)
PE cap (4x)
2)
2)2)
2) PE nut protection cap (4x)
PE nut protection cap (4x)PE nut protection cap (4x)
PE nut protection cap (4x)
3)
3)3)
3) M8 washer (4x)
M8 washer (4x)M8 washer (4x)
M8 washer (4x)
4)
4)4)
4) M8x130 TEL screw (4x) LG*
M8x130 TEL screw (4x) LG*M8x130 TEL screw (4x) LG*
M8x130 TEL screw (4x) LG*
5)
5)5)
5) M6
M6M6
M6 3x60 TE R screw (4x) AL*
3x60 TE R screw (4x) AL*3x60 TE R screw (4x) AL*
3x60 TE R screw (4x) AL*
6)
6)6)
6) A
AA
Assembled bench
ssembled benchssembled bench
ssembled bench
NOTA BENE: it is
recommended to fix the
bolts definitively and only
insert the caps once the
correct positioning of the
elements has been verified.
*
LG: wood
*AL: aluminium

Concrete deck
rubber safety
rubber safety rubber safety
rubber safety
flooring
flooringflooring
flooring

1. Excavate a hole with diameter of 30 cm and depth of 60 cm
2. Cast a first layer of concrete with thickness of 10 cm.

3. When the concrete has set, position the slide bracket in the
hole, checking the correct alignment of the lower part of the
slide with the finished ground level.

4. Complete concrete
casting as per layout.
5. When the concrete
has set, fill the
excavation hole by
compacting the infill
material up to the
finished ground level.

1. A
ttach the brackets (1) by introducing the following in
sequence: PE nut protection cap (2), M8 washer (3),
M8x25 HEX screw (4), PE cap (5)
1. Excavate two holes with d
iameter of 30 cm and depth of 60 cm
NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the
elements has been verified.
3. When the concrete has set, position the climbing board brackets in
the hole, checking the correct alignment of the lower part of the
climbing board with the finished ground level.
4. Complete concrete casting as per layout.
5. When the concrete has set, fill the hole by compacting the
infill material up to the finished ground level.
2. Cast a first layer of concrete with thickness of 10 cm.

1.
1.1.
1. Drill.
Drill.Drill.
Drill.
2.
2.2.
2. Clean the hole thoroughly using an air pump and small brushes.
Clean the hole thoroughly using an air pump and small brushes.Clean the hole thoroughly using an air pump and small brushes.
Clean the hole thoroughly using an air pump and small brushes.
3.
3.3.
3.
Insert the anchor into the hole present on the bracket with the
Insert the anchor into the hole present on the bracket with the Insert the anchor into the hole present on the bracket with the
Insert the anchor into the hole present on the bracket with the
aid of a hammer.
aid of a hammer.aid of a hammer.
aid of a hammer.
4.
4.4.
4. Tighten using dynamometric wrench.
Tighten using dynamometric wrench.Tighten using dynamometric wrench.
Tighten using dynamometric wrench.
rubb
er safety flooring
4 x M
4 x M4 x M
4 x M
10x90 screw anchors
10x90 screw anchors10x90 screw anchors
10x90 screw anchors

Article num.
Quantity
CODE N.
NAME
1 1 xfe265 59x59x35 stainless steel angle bracket
2 2 xpe10 PE nut protection cap
3 2 xpe116 PE cap
4 1
_
M10 self-locking nut
5 1
_
M8x115 screw anchor
6 1
_
Ø10 washer
1.
Position the slide on the support surface, marking the position of the
screw anchor.
2. Drill the support surface and position the screw anchor.
3.
ix the angle bracket to the support surface using the relevant bolts,
as indicated in the figure.
N.B. The combination of colours and models represented is
purely indicative.
The slide can be at a height of 84-144-192 cm.

1. Position the climbing board on the support surface and
mark the position of the screw anchors.
2. Drill the support surface and position the screw anchors.
3. ix the angle brackets to the support surface using the
relevant bolts, as indicated in the figure.
NOTE: the combination of colours and models
represented is purely indicative.
The climbing board can be at a height of 84-
144-192 cm.
Article
num.
Quantity
CODE N.
NAME
1 2 xpe10 PE nut protection cap
2 2 xpe116 PE cap
3 1 - PE climbing board
4 2 xfe265 59x59x35 stainless steel angle
bracket
5 2
_
M10 self-locking nut
6 2
_
Ø10 washer
7 2 - M8x115 screw anchor