Holzhof MAX XM 208 LP PUR User manual

MAX XM 208 LP PUR
line assembly
instructions

ASSEMBLY SEQUEN E:
1. STRUTS AND PLATFORMS 5. PARAPETS
2. BRIDGE 6. ROOFS
3. STEPS 7. GYM
4. SLIDES 8. UNDERGROUND LAYING/AN HORAGE OF THE STRU TURE

NOTA BENE: it is recommended to fix the bolts
definitively and only insert the caps once the
correct positioning of the elements has been
verified.
NOTE:
-The colours and models in the
image are purely indicative.
-
The platform can be in engineered wood
or wooden planking.
Article
num.
fixing
ODE N.
NAME
12xpe11 Shaped PE nut protection cap
22xpe10 PE nut protection cap
34xpe116 PE cap
4
4
_
ISO7089 Ø8 washer
5
2
_
UNI7473 M8 self
-
locking nut
7
2
-
UNI4017
M8X155
HEX S REW

horizontal
f
rom h.120cm to 144cm
from h.144cm to 168cm
from h.168cm to 192cm
f
ro
m h.84
cm to 1
20
cm
f
ro
m h.144
cm to 1
92
cm
f
ro
m h.84
cm to 1
44
cm

1. ontrol the exact internal distance between the tower
struts and the respective heights of the platforms.
platform h.
struts internal
distance

1. Place the bridge shims (1) on the platforms of
both towers, in axis with the centre line of the
struts, inserting the fixing bolts as indicated in
the figure.
NOTE: colours and models represented are
purely indicative.
Article num.
i
n
struction02
/Quantity
ODE N.
NAME
1 4 xls4 Shim
2 8 xpe10 PE nut protection cap
3 8 xpe116 PE cap
4 8
- UNI704 M8x180 TEL S REW
5 8
- IS07089 Ø8 washer

1.
Position the holes of the bridge beam (1) in axis with the holes of th
e
platform frame pre-drilled table, inserting the bolts required for fixing as
indicated in the figure.
2. Repeat the operation on the other side of the bridge.
M8x80 TEL screw
Article num.
Quantity
CODE N.
NAME
1 2 XII36 Fixing beam
2 8 xpe10 PE nut protection cap
3 16 xpe116 PE cap
4 16
-
ISO7089 Ø8 washer
5 8
-
M8x155 HEX SCREW
6 8
-
UNI7473 M8 self-locking nut
7 8 xpe11 Shaped PE nut protection cap

1.
Position the parapet between the two struts at 7 cm
in height from the platform
2. heck the correct parallelism and verticality
between struts and platform.
3.
Insert the nuts and bolts necessary for fixing, as
indicated in the figure.
NOTA BENE It is recommended to fix the bolts definitively once the
correct positioning of the elements has been verified.
Article
num.
Quantity
ODE N.
NAME
14xpe10 PE nut protection cap
2
4
_
IS07089 Ø8 washer
3
4
_
UNI704 M8x80 TEL S REW
44xpe116 PE cap
54xfe275 Stainless steel angle bracket

1. Fix the slide archway (2) to the struts via
the M6x140 TORX screws, inserting them
into the pre-drilled holes present.
1)
M6x140 TORX S REW (4x)
2) Max wooden slide archway (1x)
NOTA BENE It is
recommended to fix the
bolts definitively once the
correct positioning of the
elements has been verified.

1. Fix the slide (2) to the archway
using the M6x80 TORX screws, to be
inserted into the pre-drilled holes.
1)
M6x80 TORX screw (2x)
2) Max wooden slide body (1x)

Article num.
support
01/Quantity
CO E N.
NAME
1 1 - Side panels with wooden steps assembled
2 4 xpe10 PE nut protection cap
3 4 xpe116 PE cap
4 2 - UNI4017 M8X150 HEX SCREW
5 4 - IS07089 Ø8 washer
6 2 - UNI7473 M8 self-locking nut
7 2 xlls104 Small strut for steps to be supported
1.
Position the first small strut (7) at the inner lower part of the steps side
panel (1), without fixing it completely; using the bolts as indicated in the
figure.
2. Repeat the same procedure for the second (8) small strut on the other
side.
O NOT FIX THE BOLTS COMPLETELY AN O NOT POSITION THE CAPS
IN THIS PHASE.
COLOURS AN MO ELS REPRESENTE ARE PURELY IN ICATIVE.
THE STEPS CAN MEASURE 84 - 144 - 192 cm. IN HEIGHT.
NOTA BENE: it is recommended to fix the bolts
definitively and only insert the caps once the
correct positioning of the elements has been
verified.
SUPPORT SOLUTION

1.
Position the steps small struts in the previously excavated
holes, moving the upper part of the steps towards the tower
platform table (6).
2. Check that the angle brackets are in axis with the holes
present on the table (6) and insert the bolts used for fixing as
shown in the figure.
FIX THE BOLTS COMPLETELY BUT O NOT
POSITION THE CAPS IN THIS PHASE.
N.B. The platform can be in
engineered wood or wooden floor
boards
Article num.
underground 02/
Quantity
NAME
14PE nut protection cap
24PE cap
32UNI4017 M8x65 HEX SCREW
44IS07089 Ø8 washer
52UNI7473 M8 self-locking nut
61Assembled frame table

N.B. The platform can be in
engineered wood or
wooden floor boards
1.
Position the first hand rail (2) at the inner lower part of the steps strut.
Insert the bolts used for fixing as in the figure, without fixing it
completely and without positioning the caps (9).
2. Position the wooden shim (1) on the tower platform/strut, inserting the
bolts into the hole on the hand rail and in axis with the tower strut centre
line, as indicated in the figure, without fixing it completely and without
positioning the caps (4).
3. Repeat the same operations for the other three hand rails.
4.
Fix the bolts definitively and position the caps (9), which were not
positioned in the previous phases.
Article num.
support
03/Quantity
CO E N.
NAME
12xls68 Upper wooden shim
24xls25 Wooden hand rail
34xpe11 Shaped PE nut protection cap
44-UNI704 M8x220 TEL SCREW
54-UNI40l 7 M8x140 HEX SCREW
612 -ISO7089 Ø8 washer
74-UNI7473 M8 self-locking nut
88xpe10 PE nut protection cap
912 xpe116 PE cap

Article
num.
Quantity
ODE N.
NAME
11-Max wooden roof
28
xpe10 PE nut protection cap
38
xpe116 PE cap
48_
IS07089 Ø8 washer
54_M8x60 HEX screw
7
8_M8x60 HEX S REW
84xfea 115 Bracket for Max wooden roof
NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the
elements has been verified.
1. Fix the 4 brackets to the upper end of
the struts, inserting the nut protection cap,
M8 washer and
M8x80 HEX screw.
2. Position the roof by placing the small
beams on the brackets.
heck that the roof is centred and then fix
inserting the nut protection cap, M8
washer and M8x60 HEX screws into the two
holes present in the bracket.
3. heck that everything is positioned
correctly and then fix definitively and
position the caps.
M8x60 HEX screw
M8x80 HEX screw

1. Position the climbing net beam (3) in the housing of
the pre-assembled climbing ladder (4), inserting the
bolts necessary for fixing as in the figure, however
without fixing it completely and without positioning the
caps.
NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the
elements has been verified.
* lg: wood
al: aluminium

1) 1 x climbing net strut
2) 1 x rope beam
3) 1 x net beam
4) 1 x climbing ladder
5) 4 x M 8x80 TEL S REW (lg*)
5) 4 x M6 3x60 TEFR S REW (al*)
6) 3 x M8x110 HEX S REW
7) 4 x PE nut protection cap
8) 6 x shaped PE nut protection cap
9) 10 x M8 washers
10) 3 x M8 self-locking nuts
11) 10 x PE cap
2. Position the climbing rope beam (2) in the housing of
the pre-
assembled climbing ladder (10), inserting the bolts
necessary for fixing as in the figure, without fixing it
completely and without positioning the caps.
3. Position the climbing net strut (1) in the housing of the
climbing net beam (2), inserting the bolts necessary for
fixing as in the figure, without fixing it completely and
without positioning the caps.
4. If the structure is to be laid underground, position the
gym in the excavation holes made previously as per
excavations layout. Attach the gym to the tower struts by
inserting the bolts necessary for fixing, as indicated in the
figure.

1. Position the upper part of the climbing net (1), inserting the bolts
necessary for fixing into the thimbles as indicated the figure, without
fixing it completely and without positioning the caps.
2. Position the climbing rope (6), inserting the bolts necessary for
fixing into the thimbles as indicated the figure, without fixing it
completely and without positioning the caps.
3. Once the correct parallelism and verticality
have been checked, fix all bolts definitively.
4. Position all caps (1).
NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the
elements has been verified.
1) 32 x PE cap
2) 32 x M8 washer
3) 13 x shaped PE nut
protection cap
4) 13 x M8 self-locking nuts
5) 1 x climbing rope
6) 1 x climbing net
7)
13 x M8x115 HEX
S REWS

NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the
elements has been verified.
UNDER
GROUND
AN HORAGE
climbing rope
-
climbing rope
-
1. Drill.
2.
lean the hole thoroughly using an air
pump and small brushes.
3. Insert the anchor into the ho
le present
on the bracket with the aid of a hammer.
4. Tighten using
dynamometric wrench.
-M10 self-locking nut
M10 washer
-M10 screw anchor
PE cap
M8 self-locking nut—
PE washer
PE nut protection cap
underground bracket
PE nut protection
cap, M8 washer
M8x35 Hex Screw
—PE cap
excavation hole 30x50 cm.

oncrete deck
rubber safety
flooring

1. Excavate a hole with diameter of 30 cm and depth of 60 cm
2. ast a first layer of concrete with thickness of 10 cm.