Home Accents Holiday 1003142984 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.6 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for proper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, when retiring for the night,
or if left unattended.
i)Thisisanelectricproduct–notatoy! Toavoidriskoffire,burnspersonal
injuryandelectricshockitshouldnot beplayedwithorplacedwheresmall
children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
m)Do not cover theproductwithcloth,paperoranymaterialnotpartof the
product when in use.
n)This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows, unplug
theproduct fromthe outlet. Alsounplugany additional stringsorproducts
that may be attached to the product. Replace the fuse as per the User
Serving instructions (follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a short-circuit may be
present and the product should be discarded.
o) Read and follow all instructions that are on the product or provided with
the product.
p) SAVE THESE INSTRUCTIONS.
Pre-Assembly
Package Contents
Part Description Quantity
A Tree top 1
B Upper middle section 1
C Lower middle section 1
D Tree bottom 1
E Tree stand 1
F Power cord 1
7.5 ft Warm White / Multi Micro Dot LED 9 Function
One Plug Tree
SKU# 1003142984
Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step2. Open the standto a 90 degree angleuntil the hole linesupwith the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
CAUTION! – ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree
Pleaseremove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (D) into the tree stand and tighten the screw.
(See Fig. 1)
Step2. Insertlowermiddlesection(C)intothetreebottom(D).(SeeFig.2)
Step 3 Insert upper middle section (B) into the lower middle section (C).
(See Fig. 3)
Step 4. Insert tree top (A) into the upper middle section (B). (See Fig. 4)
Warning: There is a tree top connector on the tree top (A). Do
not overload. Connect other lighting strings or tree toppers
end-to-end up to a maximum of 216 Watts (1.8 Amps). Do not
interconnect low-voltage products.
Step 5. Insert the provided power cord into the connector on the tree
bottom (D) in right direction porperly and tightly (always match the
protuberance of the end connector of power cord to the concave
of the connector found on the tree bottom (D) according to the
magnified drawing on fig. 5.).
Step6. Allowbranchestofall into placeorgentlypull branchesup andout.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 6)
Step 7. Shape the branches. Starting with tips closest to the pole, shape
onetiptotheright,one totheleftandoneatthecenterofthemain
stem. Repeat pattern for each branch. (See Fig. 7)

Step 8. Plug the power cord into a proper outlet. This tree comes with a
control box to change functions. This tree is Color Changing, the
9 lighting options available are:
1. Steady On
2. Steady Warm White
3. Flashing Warm White
4. Fade In and Fade Out Warm White
5. Steady Multicolor
6. Flashing Multicolor
7. Fade In and Fade Out Multicolor
8. Sequential Multicolor & Warm White
9. Color Changing
These functions can be changed by using the control box.
Please see Instructions of control box as below.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Instruction of control box
Instruction of control box
1. Press the ON/OFF Timer button on control box more than 1 second
to turn on and off timer function.
2. Press the ON/OFF Timer button on control box for more than 2
seconds to select below timer hours:
i. Indicator lights of timer on control box turn on red:
The tree lights will automatically run through a 2-hours
ON, 22-hours OFF cycle.
ii. Indicator lights of timer on control box turn on green:
The tree lights will automatically run through a 4-hours
ON, 20-hours OFF cycle.
iii. Indicator lights of timer on control box turn on blue:
The tree lights will automatically run through a 6-hours
ON, 18-hours OFF cycle.
iv. Indicator lights of timer on control box turn on yellow:
The tree lights will automatically run through an 8-hours
ON, 16-hours OFF cycle.
No memory mode on timer whether the tree or the timer is
re-started.
3. Press the Function button to select the lighting functions below:
1) Steady On
2) Steady Warm White
3) Flashing Warm White
4) Fade In and Fade Out Warm White
5) Steady Multicolor
6) Flashing Multicolor
7) Fade In and Fade Out Multicolor
8) Sequential Multicolor & Warm White
9) Color Changing
There is memory mode on Function adjustment.
Maintenance
Replace the fuse.
1. Power cord fuse replacement (replaceable 3 amp, 125 volt fuse is
located in spare parts bag):
2. Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.
3. Open fuse cover. Slide open the fuse access cover on
back of control box.
4. Remove fuse carefully.
5. Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with
product).
6. Close fuse cover. Slide closed the fuse access cover.
7. Risk of fire. Do not replace attachment plug. Contains a safety device
(fuse)that shouldnotberemoved. Discard productifthe attachmentplug
is damaged.
CAUTION! – ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE REPLACEMENT.
CAUTION: To reduce the risk of fire or electric shock, do not
attempt to replace lamps or modify string.

Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the power cord from the wall outlet. And remove your
power cord from tree bottom (D) and save them.
Step3. Gentlyliftthe treetopstraightup toremovefromthe center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step5. Carefullyplacealltreesectionsintoashippingboxandtapeitshut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem Solution
The tree
does not
light
Ensurethat alltreesectionsare connectedwellandthat
the tree is plugged into the wall outlet. Make sure the
power cord is well connected to the tree bottom (D).
Check for blown fuses at the power cord plug. Replace
as needed with the replacement fuses provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Warning: Please note that changes or modifications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician
for help.
UL Model No. LTW36C-12V1C