Home Styles 88 6001 00 User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 6001 00
The Pro Foosball Table
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319

Part List
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
A.
Side Panel
2 Pcs.
E.
Leg
2 Pcs.
M.
End Ramp
2 Pcs.
T.
Ball Run
2 Pcs.
U.
Goal
2 Pcs.
V.
Ball Catch
2 Pcs.
W.
Home Score
1 Pc.
X.
Visitor Score
1 Pc.
S.
Ball
4 Pcs.
R.
Five Player Rod
2 Pcs.
Q.
Two Player Rod
2 Pcs.
P.
Three Player Rod
4 Pcs.
N.
End Ramp
2 Pcs.
O.
Side Ramp
2 Pcs.
K.
Home Player
13 Pcs.
L.
Visitor Player
13 Pcs.
H.
Cup Holder
4 Pcs.
F.
Leg
2 Pcs.
G.
End Top Rail
2 Pcs.
I.
Ball Entry Cup
2 Sets
J.
Leveler
4 Pcs.
B.
End Panel
2 Pcs.
C.
Playing Field
1 Pc.
D.
Bar
2 Pcs.
Straight Hex
1 Pc.
Head Cap Bolt (short)
20 Pcs.(+1 extra)
Bumper
16 Pcs.
Flat Head Screw
(short)
8 Pcs.(+1 extra)
Flat Head Screw
(middle)
18 Pcs.(+1 extra)
Flat Head Screw
(long)
4 Pcs.(+1 extra)
Round Head
Screw (long)
18 Pcs.(+1 extra)
Round Head
Screw (short)
12 Pcs.(+1 extra)
Round Head Bolt
26 Pcs.(+1 extra)
Head Cap Bolt (long)
8 Pcs. (+1 extra)
Flat Washer (large)
20 Pcs. (+1 extra)
Flat Washer (small)
8 Pcs. (+1 extra)
Plastic Washer
16 Pcs.
Lock Nut
26 Pcs. (+1 extra)
Handle
8 Pcs.
End Cap
8 Pcs.
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
Hex Wrench
1 Pc.
1
10 11 12 13 14 15 16 17
2 3 4 5 6 7 8 9

Assembly Instructions 3
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the oor.
STEP 1
Attach End Panels (B) to Side Panel (A)
with Head Cap Bolts (long) and
Flat Washers (small).
(See gure 1)
Slide Playing Field (C) into position.
Attach Side Panel (A) to
unit with Head Cap Bolts (long)
and Flat Washers (small).
STEP 2
Insert Flat Head Screws (middle)
into the pre-drilled holes of playing
eld.
Attach Leg (F) to unit with Head
Cap Bolts (short) and Flat Washers
(large).
Insert Bar (D) into the pre-drilled
hole of Leg (F).
Attach Leg (E) to unit with Head
Cap Bolts (short) and Flat Washers
(large).
Repeat this step on other end of
unit.
B
B
B
B
B
D
B
E
B
F
B
C
B
A
B
A
Head Cap Bolt (long)
Flat Washer (small)
Flat Washer (small)
Head Cap Bolt (long)
Flat Washer (large)
Head Cap Bolt (short)
Flat Head Screw (middle)
Figure 1
/6
11
11
12
2
5
13
13

Assembly Instructions 4
STEP 3
Assemble Goals (U), Ball Catches (V)
and Ball Runs (T).
Attach the set to both ends of unit
with Round Head Screws (short).
Insert Levelers (J) into the holes
pre-drilled into the bottom of the legs.
STEP 4
Turn the unit upright to its’ normal
position.
Attach End Top Rails (G) to unit with
Flat Head Screws (short).
Remove the sticker covers from the
bottom side of End Ramps (M), (N)
and Side Ramps (O).
Attach End Ramps (M), (N)
and Side Ramps (O) to unit by
pressing them into place on the side
and ends of the playing eld.
B
U
B
T
B
V
B
N
B
G
B
G
B
N
B
O
B
O
B
B
B
JB
J
B
J
B
J
M
M
Round Head Screw (short)
Flat Head Screw (short)
/6
8
4

Assembly Instructions 5
Figure 2
STEP 5
Attach Ball Entry Cups (I) into both sides
of unit with Round Head Screws (long). (See gure 2)
Attach Cup Holders (H) to both ends of unit with
Round Head Screws (long).
Slide two Three Player Rods (P), a Two Player Rod (Q)
and a Five Player Rod (R) into the holes in one side of
unit with the Handle hole end of the player rods inserted last.
Slide onto the player rods in order; Bumper,
Plastic Washer (ange facing in), appropriate number of
Visitor Players (L) (round chest hole facing Home goal), Plastic
Washer (ange facing in) and Bumper. Slide the player rods through the corresponding holes in
other side of unit.
Attach Visitor Players (L) to Three Player Rods (P), Two Player Rod (Q) and Five Player Rod (R)
with Round Head Bolts and Lock Nuts. (See gure 3)
Repeat this process for Home Players (K) on other side of unit.
Figure 3
B
P
B
P
B
H
B
H
B
I
B
QB
R
B
L
Round Head Screw (long)
Handle hole end
Round Head
Screw (long)
Bumper
Plastic Washer
Round Head Bolt
Lock Nut
/6
7
3
14
9
15
7

Assembly Instructions 6
STEP 6
Attach Home Score (W) and Visitor Score (X) to
the pre-drilled of unit with Flat Head Screws (long).
Slide Handles and End Caps rmly into position.
To level the table, adjust the levelers on the bottom of
the legs. (See gure 4)
Note: Unit must be level to work properly.
B
X
B
W
Flat Head Screw (long)
End Cap
Handle
Figure 4
/6
6
17
16