Home2Link Shelly Plus Smoke Installation and operating manual

Pagina 1
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Shelly&Plus&Smoke&User&and&Safety&Guide&
Read%before%use%
This document contains important technical and safety information about the device, its safety
use and installation.
⚠
ATTENTION! Before beginning the installation, please read carefully and entirely this
guide and any other documents accompanying the device. Failure to follow the installation
procedures could lead to malfunction, danger to your health and life, violation of the law or
refusal of legal and/or commercial guarantee (if any). Allterco Robotics EOOD is not
responsible for any loss or damage in case of incorrect installation or improper operation of
this device due to failure of following the user and safety instructions in this guide.
Shelly® devices are delivered with factory-installed firmware. If firmware updates are
necessary to keep the devices in conformity, including security updates, Allterco Robotics
EOOD will provide the updates free of charge through the device embedded Web Interface or
Shelly Mobile Application, where the information about the current firmware version is
available. The choice to install or not the Device firmware updates is the User’s sole
responsibility. Allterco Robotics EOOD shall not be liable for any lack of conformity of the
Device caused by failure of the User to install the provided updates in a timely manner.

Pagina 2
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Short%description%
Shelly Plus Smoke (the Device) is a smart photoelectric smoke alarm, which is effective at
detecting slow fires that smolder for hours before bursting into flames.
Sources of these fires may include burning cigarettes left on couches or bedding.
A: Buzzer
B: Control button
C: LED indication
D: Smoke inlet
Features%
• Battery operated: Replaceable lithium battery helps to extend the lifetime of smoke
alarm.
• LED indication: Light flashes approximately every 53 seconds confirming the smoke
alarm is powered and working normally.
• Low battery warning: Alarm beeps every 53 seconds when the battery is low.
• Alarm pause (Hush mode): Silence your smoke alarm device by momentarily
pressing the control button when non-emergency smoke causes nuisance alarm. The
red light flashes every 10 seconds to remind you that the smoke alarm device has been

Pagina 3
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
silenced. The alarm will automatically be reset after 10 minutes, and sound the alarm
if particles of combustion are still present.
• Test function: Press the test button periodically to check and confirm the smoke alarm
is working normally.
• Audible and visible alarm signals: Red light will start flashing quickly and the
buzzer will start beeping, when the detected smoke level reaches the alarm threshold
of the Device.
• Easy Installation: Fixings supplied.
Important%safety%information%
⚠
CAUTION! The Device should be installed only by a licensed, qualified electrician.
Observe and follow all local and national electrical and building regulations for installation.
⚠
CAUTION! Do not remove or disconnect battery to silence unwanted alarms! This will
remove your protection. Open windows or evacuate the air around the smoke alarm device to
silence it.
⚠
CAUTION! Test the Device weekly to ensure proper operation! The control button
accurately tests all smoke alarm functions. Do not use any other test method!
⚠
CAUTION! This smoke alarm device is not designed to be the primary protection for
buildings that require complete fire alarm systems. Buildings of this type include hotels,
motels, dormitories, hospitals, nursing homes, and group homes. This is true even if they were
once single family homes. However, this smoke alarm device may be used inside individual
rooms as supplemental protection.
⚠
CAUTION! Smoke alarm devices may not alert every household member every time. The
alarm buzzer is loud in order to alert individuals to a potential danger. However, there may be
limiting circumstances where a household member may not hear the alarm (i.e., outdoor or
indoor noise, sound sleepers, drug or alcohol usage, the hard of hearing, etc.). If you suspect
that this smoke alarm device may not alert a household member, install and maintain special
smoke alarm devices. Household members must hear the alarm warning sound and quickly
respond to it to reduce the risk of damage, injury, or death that may result from fire. If a
household member is hard of hearing, install special smoke alarm devices with lights or
vibrating devices to alert occupants.
⚠
CAUTION! Smoke alarm devices can sound their alarms only when they detect smoke.
Smoke alarm devices detect combustion particles in the air. They do not sense heat, flame, or
gas. This smoke alarm device is designed to give audible warning of a developing fire.
However, many fires are fast-burning, explosive, or intentional. Others are caused by
carelessness or safety hazards. Smoke may not reach the smoke alarm device quickly enough
to ensure safe escape.

Pagina 4
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
⚠
CAUTION! Smoke alarm devices have limitations. This smoke alarm device is not
foolproof and is not warranted to protect lives or property from fire. Smoke alarm devices are
not a substitute for insurance. Homeowners and renters should insure their lives and property.
In addition, it is possible for the smoke alarm device to fail at any time. For this reason, you
must test the smoke alarm device weekly.
⚠
CAUTION! The Device is intended for indoor use only!
⚠
CAUTION! Protect the Device from dirt and moisture!
⚠
CAUTION! Do not use the Device in a damp environment!
⚠
CAUTION! Do not paint over the smoke alarm.
⚠
CAUTION The smoke detector must not be exposed to excessive heat such as sunshine,
fire or similar.
⚠
CAUTION! Do not cover or tape the smoke inlets and buzzer openings!
⚠
CAUTION! Do not disassemble or modify the Device!
⚠
CAUTION! Do not allow children to play with the device, especially with the control
button!
% %

Pagina 5
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Where%to%locate%
As a minimum, smoke alarm devices should be located between sleeping areas and potential
sources of fire such as living rooms and kitchens.

Pagina 6
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
⬤ Smoke alarm devices for limited protection
○ Additional smoke alarm devices for better coverage
△ Heat alarms
In single story homes with one sleeping area, a smoke alarm device should be installed in the
hallway, as close as possible to the living accommodation.
To ensure audibility in bedrooms, no smoke alarm device should be further away than 3 m /
10 ft from any bedroom door. It may be necessary to install more than one smoke alarm
device, particularly the hallway is more than 15 m / 49 ft long.
In single story homes with two separate sleeping areas, a minimum of two smoke alarm
devices are required, one outside each sleeping area.
In multilevel or split level homes, as a minimum a smoke alarm device should be installed on
the ground floor between the staircase and any room in which a fire might start and on each
story in circulation areas which form part of escape route (normally hallways and landings).
Additional alarms should be installed in bedrooms in anticipation of fires originating here,
caused by faulty wiring, lights, appliances, smokers or other hazards.
For best protection, smoke alarm devices should be installed in every room in your home,
apart from those listed in the Locations to avoid section. Heat alarms should be used in
kitchens, boiler rooms, laundry rooms, garages and such like, where smoke alarm devices
would be unsuitable.
Install smoke alarm devices in circulation areas at a distance no greater than 7.5 m / 25 ft from
the farthest wall, no greater than 7.5 m / 25 ft from a door to any room in which a fire might
start and no greater than 7.5 m / 25 ft from the next smoke alarm device.
As it is impossible to predict the source of a fire, the best location for an alarm is usually the
center of a room or hallway. If it is necessary to place a smoke alarm device on a wall, always
locate the detection element of the alarm 15 to 30 cm / 6 to 12 in below the ceiling and the
bottom of the alarm above the level of doors and other openings.
In rooms with simple sloped, peaked or gabled ceilings, install smoke alarm devices on the
ceiling 90 cm / 3 ft from the highest point of the ceiling. “Dead-air” at the peak of a ceiling
may prevent the smoke from reaching the alarm in time to provide an early warning.

Pagina 7
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
A: “Dead-air” area
Relocate the unit if it often gives false alarms. See Locations to avoid.
Locations%to%avoid%
• In turbulent air from fans, heaters, doors, windows, etc., which could draw smoke
away from the alarm.
• At the peak of an “A” frame ceiling. “Dead-air” at the top may prevent smoke from
reaching the alarm in time to provide early warning.
• In insect-infested areas. Tiny insects may affect performance.
• In kitchens, boiler rooms, laundry rooms, garages. Combustion particles from cooking
or car exhaust, dust and moisture could trigger a nuisance alarm.
• In very dusty or dirty areas. Dirt and dust can build up and impair performance.
• Within 30 cm / 12 in of light fittings or room corners. In locations which would make
routine testing or maintenance hazardous (e.g. over a stairwell).
• On poorly insulated walls or ceilings.
• Within 1.5 m / 5 ft of fluorescent light fittings.
Installation%
⚠
CAUTION! Do not use the Device if it has been damaged!
⚠
CAUTION! Do not attempt to service or repair the Device yourself!
! !

Pagina 8
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Package!contents!
A: 1x mounting bracket
B: 1x smoke alarm
C: 3x anchor plugs
D: 3x screws

Pagina 9
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Powering!the!Device!
Remove the mounting bracket from the smoke alarm by turning it counterclockwise.
Pull out the plastic isolation tab.
Press and hold the control button for about 3 seconds. Confirm that the LED indication
flashes rapidly, and the buzzer emits short loud beeps.
! !

Pagina 10
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Mounting!
Select an appropriate location and use the mounting bracket to mark the drilling points and
punch 3 holes in the mounting surface.
Insert the 3 anchor plugs in the holes and secure the mounting bracket to the surface with the
help of the 3 screws.

Pagina 11
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Rotate the Device clockwise onto the mounting bracket until you hear a click, indicating that
the Device is in place.
Press and hold the control button for about 3 seconds. Confirm that the LED indication
flashes rapidly, and the buzzer emits short loud beeps.

Pagina 12
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
False%alarm%control%
The Device features a False Alarm Control, which, when activated, will silence unwanted
alarms for up to 10 minutes.
Press and release the control button during an unwanted alarm to silence the alarm buzzer.
This will set the Device in False Alarm Control mode.
If the smoke alarm device does not go into False Alarm Control and continues to sound its
loud alarm signal, or if it initially goes into False Alarm Control then resounds the alarm, the
smoke is too heavy and could be a possibly dangerous situation take emergency action.
Battery%replacement%
When the battery becomes low, the smoke alarm device will beep once every 53 seconds (low
battery warning).
You must replace the battery with a new one immediately to continue your protection.
Rotate counter clockwise the Device out of the mounting bracket.
Replace the battery with a new one.
⚠
CAUTION! Replace only with the same or equivalent type! Danger of explosion if battery
is incorrectly placed.
% %

Pagina 13
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Testing%
This unit has been designed to be as maintenance-free as possible, but there are a few simple
things you must do to keep it working properly:
Test smoke alarm devices weekly and upon returning from vacation or when no one has been
in the household for several days.
⚠
CAUTION! The test button accurately tests all functions. Do not use an open flame to test
this smoke alarm device. You may ignite and damage the smoke alarm device or your home.
⚠
CAUTION! Stand at arm’s length from the smoke alarm device when testing.
The alarm buzzer is quite loud and can be harmful to hearing.
Press and hold the test button for more than than 3 second to test the alarm.
The alarm will sound loud short beeps.
If smoke alarm device does not sound, check whether the alarm is properly attached to the
mounting bracket.
⚠
ATTENTION! Replace the Device 10 years after installation or if the test function does
not operate properly!
Cleaning%
Clean the smoke alarm device at least once a month.
Gently clean the outside of the smoke alarm device with a soft cloth.
⚠
CAUTION! Do not use aggressive detergents!
⚠
CAUTION! Do not immerse the Device or wash it under running water!
⚠
ATTENTION! If the Device becomes contaminated by excessive dirt, dust and/or grime,
and cannot be cleaned to avoid unwanted alarms, replace the unit immediately.
% %

Pagina 14
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Visual%and%audible%signals%
Normal!operation:!
• Red light flash once every 53 seconds
• No sound
Testing:!
• 3 red light flashes
• 3 short beeps
Alarm:!
• Continuous red light flashes
• Continuous loud beeps
Low!battery!warning:!
• Red light flash once every 53 seconds
• Short beep once every 53 seconds
Malfunction:!
• Red light flash twice every 53 seconds
• No sound
Hushed!alarm:!
• Red light flash once every 10 seconds
• No sound (for about 10 minutes)
Hushed!low!battery!warning:!
• Red light flash once every 53 seconds
• No sound (for about 12 hours)
Control%button%
• Press and hold for 3 sec to test the Device.
• Press briefly to silence an alarm.
• Press briefly 3 times to put the Device in Setup mode for 2 minutes.
• Press briefly 5 times to factory reset. The Device stays in Setup mode for 2 minutes.

Pagina 15
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Inclusion%to%Shelly%Cloud%
If you choose to use the Device with the Shelly Cloud mobile application and Shelly Cloud
service, instructions on how to connect the Device to the Cloud and control it through the
Shelly App can be found in the Shelly Application Guide.
The Shelly Mobile Application and Shelly Cloud service are not conditions for the Device to
function properly. This Device can be used stand-alone or with various other home
automation platforms and protocols.
Connecting%manually%to%a%local%Wi-Fi%network%
Shelly Plus Smoke can be managed and controlled through its embedded web interface. Make
sure the Device is in Setup mode, its access point (ShellyPlusSmoke-XXXXXXXXXXXX) is
enabled and you are connected to it using a Wi-Fi enabled device. From a web browser open
the Device Web Interface by navigating to http://192.168.33.1. Press Settings from the Main
menu and then the WiFi bar under Network settings.
Enable Wi-Fi network by checking the corresponding checkbox in the WiFi1
settings and WiFi2 settings (backup network) panels. Select the Wi-Fi network you want to
connect the Device to from the NETWORS dropdown menu. Enter the Wi-Fi network
password and press Save settings button in the respective panel. You can also set a static IP by
checking the Set static IP and filling in the additional fields below.
The Network SSID, the Device URL and the connection strength will appear in blue color at
the top of the Wi-Fi settings panel, when the device is successfully connected to the Wi-Fi
network.
⚠
RECOMMENDATION: For security reasons we recommend disabling or password
protecting the Device AP (Networks / Access Point), after the Device successful connection
to the local Wi-Fi network.
% %

Pagina 16
Home2Link B.V.
Tingietersweg 107 2031 ER HAARLEM Tel: [phone]
Postbus 2103 2002 CC HAARLEM www.home2link.nl [e-mail]
KvK Nr. 70620326 BTW Nr. NL NL858397262B01
NL14RABO0326619755
Disposal%&%Recycling%
This refers to the waste of electrical and electronic equipment. It is applicable in the EU and
other countries to collect waste separately.
This symbol on the product or in the accompanying literature indicating that the product
should not be disposed of in the daily waste. Shelly Plus Smoke must be recycled to avoid
possible damage to the environment or human health from uncontrolled waste disposal and to
promote the reuse of materials and resources. It is your responsibility to dispose of the device
separately from general household waste it is already unusable.