HomeDefender HD-P910 User manual

MOTION SENSOR
PIR - TWO WAY
PET IMMUNE
Printed in Hong Kong
PA:HD-P91/EN-Aug.2012-V1.0
PROTECT
YOUR HOME
INSTALLATION AND USER
MANUAL
HD-P910

Front View Back View
Motion Sensor PIR HD-P910 Two-Way
1 2
HD-P910 Motion Sensor Two-Way is a sophisticated passive infra-red
ray instrument (P.I.R.).
It consist of digital dual-cor digital fuzzy logic infrared control chip
and intelligent analisys which effectively identify interference signal
from body movements caused also by domestic pets and drastically
reduce false alarm rate (Pet Immune).
With automatic temperature compensation and anti-air turbolence
technology, it easily adapt to environmental changes.
While system is not armed the detector enter in energy save mode to
prolong the battery life.
1. Detection Window
2. LED Indicator
3. Bracket
4. Test Button
Note: if the LED indicator flashes repeatedly the sensor is carrying out
an automatic test. When it flashes twice the test is complete and the
sensor is ready to detect.
Once movement in front of the sensor has been detected the sensor
transmits its status to the control panel and flashes once.
N.B.: if the LED indicator stays ON, the battery is discharged.
Replace the battery immediately.
Low battery status will also be sent to control panel that, conse-
quently, will send SMS to programmed numbers (Two-Way function).
Internal View
Infrared Sensor: recognises the infra-red radiation emitted by the
human body and activates the transmitter that will set off the alarm:
sound the siren, send SMS and dial phone calls as programmed.
It must not be touched or exposed to dirt.
Tamper Switch: an unwanted opening, such as an attempt to
sabotage the sensor, will set off the alarm: sound the siren, send SMS
and dial phone calls as programmed.
Test Mode: Once the automatic test procedure is complete, press the
Test button located on the back and the sensor will activate the test
procedure to detect the presence of an intrusion every 10 seconds.
Walk in front of the sensor looking to see if the LED indicator lights up.
Every time the LED lights up it indicates the detection of a human body.
Adjust the position of the sensor so as to obtain the maximum cover-
age of the room where installed.
After 3 minutes the LED will flash twice and will go back into armed
mode.
Two-Way: it refer to the RF comunication between the sensor and the
alarm system control panel that allow to verify the battery status and
the true response of the triggering status to avoid any kind of false
alarm.
First use:
Open the case and remove
the battery protection strip
to activate the sensor.
The automatic test procedure
will start and run for about 1
minute.
Tamper Switch
Zone Mode
Jumper Setting
Infrared Sensor
Infrared Sensor
LED ON / OFF
Jumper
4

Side View
Installation
Note: for optimal coverage,
position the IR sensors in the
corners of the rooms at 2
meters of height.
Do not install the sensor
behind doors that are often
left open.
Thanks to the wide angle of volumetric coverage and the orientation
system, the motion sensor can easily be installed:
• within closed environments;
• within trepassing points;
• at right angles to any movement.
N.B.:
• Avoid direct exposure to sunlight;
• Position the sensor at a distance from heaters or sources of cold air
(air conditioners, stoves, fireplaces, etc.);
• Do not install the sensor in rooms where there is a strong presence of
steam that could cause condensation;
Operative Range
View from above Side View
Technical Specification
Product Name:
PIR Motion Sensor
Two-Way Pet Immune
Model:
HD-P910
Power Supply:
DC 3V (Battery AA 1.5V LR6 x 2 pcs.)
Stand-By Current:
≤90 μA
Alarm Current:
≤9.5 mA
Operative Range:
8m / 110º
Transmission Distance:
≤80 m (open area)
Transmission Frequency:
315 MHz / 433 MHz (± 75 KHz)
Housing Material:
ABS Plastic
Operative Conditions:
Temperature: -10ºC ~ 55ºC
Umidity: ≤80% (non condensing)
Dimensioni (L x W x D):
Sensor: 108 x 52 x 36.8mm
Braket: 52 x 30 x 26.5mm
3 4

Setting Zone Mode
Home Mode Zone Normal Mode Zone Delay Mode Zone
24H Mode Zone
It is possible to set three different zone modes in the system:
1. Home Zone Mode: set on the PIR motion sensors within the rooms of
the premises.
2. Normal Zone Mode: set on all the other sensors.
3. Delay Time Zone Mode: set on the door/window sensor on the main
entrance.
N.B.: after each jumper setting modification it is necessary to reconnect
the modified sensor to the control panel.
Note: for detectors such as smoke,
gas, water sensor it is recommended
to position the jumper setting in 24
Hour Zone Mode.
The system will then be armed at all
time only for those specific sensors
that, if set off, will trigger the alarm,
sound the siren, send SMS and call the
programmed numbers.
Every sensor can be set in such a way that it can respond to the type of
anti-intrusion required.
To do this it is necessary to set the jumpers located close to the battery on
each sensor.
The jumper setting will reflect the operation mode chosen on the control
panel.
+39.02.45072208
TECHNICAL SUPPORT
[e-mail]
Mon. - Fri. 9:00 - 13:00
TECHNICAL SUPPORT
For help with the installation, solving
your problems and suggestions on how
to make your home or office more secure
do not hesitate to contact our free
support service.
GUARANTEE
If within one year from the date of purchase this product should
become faulty because of defects in manufacture or construction
(except for the batteries), the product will be repaired or replaced free
of charge.
Proof of purchase such as invoice or tax receipt will be required to
issue the authorisation to return the product to the authorised centre.
Please visit our web site http://www.homedefender.it and read the
FAQ section for further information on the return procedure.
DECLARATION OF COMPLIANCE
HomeDefender©products are built to professional standards in terms of safety in
line with what is required by Italian laws 186/68 and 791/77 and do not compromise
the safety of persons, of domestic animals and of property if installed and used in
line with their purpose and mounted in the correct way.
Moreover the products are within the field of application of the EU Directives (“EMC”
Directive 89/336/CEE - ratified by Decree-Law 476/92 - modified by Directive
93/68/CEE and “BT” Directive 73/23/CEE - ratified by Law 791/77 - modified by
Directive 93/68/CEE - “R&TTE” Directive 99/5/CE ratified by Legislative Decree no.
269) and comply with the essential requirements contained therein.
The EU marking on the product and/or on the packaging and/or on any use notices
that accompany the product itself “indicate presumption of compliance with the
Directives” referred to above.
HomeDefender keeps its own Technical Archive containing the documentation that
shows that the product has been examined to establish its compliance.
5