HOMEDEPOT KSTFA120AG User manual

Instruction Manual
ETLus Electric Fan
KSTFA120AG
For Household Use Only
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
This fan has a polarized plug (one blade is wider than the other). To reduce the
risk of electric shock, this plug is intended to fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safety feature.
This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse blows, unplug the product from the
outlet. Replace the fuse as per the user servicing instructions (follow product
marking for proper fuse rating) and check the product, If the replacement fuse
blows, a short-circuit may be present and the product should be discarded or
returned to an authorized service facility for examination and/or repair.
WARNING – To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This
Fan With Any Solid-State Speed Control Device.
WARNING – To Reduce The Risk Of Electric Shock, Do Not Expose to Water
or Rain.
WARNING – This is a fan – not a toy! To reduce the risk of personal injury and
electric shock, it should not be played with or placed where small children can
reach it.
When using electric appliances, basic safety precautions should always be
followed, including the following:
1. Do unplug or disconnect the appliance from the power supply before servicing.
2. Do not use gasoline, thinners, solvents, ammonias or other chemicals for
cleaning.
3. Do clean your fan regularly. Refer to the Cleaning instructions provided. Never
clean the fan in any manner other than as instructed in this manual.
4. Do not operate any fan with a damaged cord or plug. Discard fan or return to
an authorized service facility for examination and/or repair.
5. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be tripped over.
6. Do not use this product outdoors.
7. Do not use this product on wet surfaces.
8. Do not use this product in a bathtub or shower.
9. Do not use near furnaces, fireplaces, stove or other high-temperature heat
sources.
10. Do not immerse this product in water or allow water to drip into the motor
housing.
11. Do not position this fan too close to draperies because they may be drawn into
the rear guard, cutting off airflow.
SAVE THESE INSTRUCTIONS
P1-14606
P2-14606

User Servicing Instructions
Grasp plug and remove from the receptacle or other outlet device. Do not unplug
by pulling on cord. Open fuse cover (A.) by sliding access cover on top of
attachment plug towards blades. Remove fuse carefully (B.) by gently prying out
the ends of the fuse from the receptacle.
Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
Install replacement fuse (C.) by first placing the end of the fuse into the fuse
receptacle which is opposite of the blades of the plug, then carefully push in the
other end. Only push against the metal end of the fuse, not the glass center
portion. Close the fuse access cover (D.) by sliding the cover back into the plug
until it is completely closed, latches and is flush with the face of the plug.
Risk of fire. Do not replace attachment plug. Contains a safety device (fuse , AFCI,
LCDI) that should not be removed. Discard product if the attachment plug is
damaged.
Know Your Fan
Parts and Their Function
Parts Function
●Height adjust button
Use only when higher position required.
Pressing the height adjust button, pull
the slide pipe upwards.
When lower position required, just push
the slide pipe downwards.
You can adjust the height in 2 steps.
Caution: Be careful not to pinch fingers.
●Swivel button
Press down…Swivel starts
Pull up…Swivel stops
P3-14606
P4-14606

How to Assemble
CAUTION:
Do not insert the plug into the power point before assembly is complete.
(May cause electric shock or injury)
Do not press height adjustment button while fan and fan guard are
detached.
(The motor section (slide pipe) may jump out of stand, causing injury)
1. Fix the stand onto the base
●Remove the motor shaft cover.
●Check the stand direction by the
indication of front and back of
the base and stand, insert the front
protusions of stand into the concav
-es of the base, then push the
whole stand part down onto the
base until it is fitted in firmly.
●Placing the motor shaft upward,
then fix the stand and base by
turning the base fixing ring
providedclockwise.
Attention:
● Base fixing ring is temporarily attached on bottom of stand. Unscrew it
When you assemble the fan.
● Do not forcibly push the stand down onto the base. May cause damage.
● Do not put the stand onto the base in wrong direction. May cause damage.
● Do not press the height adjust button while assembling. May cause injury,
damage to the product or machine failure.
2. Fix Rear Guard and Fan Blade
●Couple protrusions (three) on the motor section to concaves (three) on the
rear guard.
●Fix them firmly by turning the guard fixing ring toward [fasten].
●Couple the pin on the motor shaft and the concave on the fan blade and
insert the fan part into the motor part. Then pressing the fan part towards
the motor part and turn the fan blade cap toward [fasten] to fix them firmly.
Attention:
● If the fan blade cap is not fastened firmly enough, fan blade may come off,
causing injury.
● Be careful not to be injured by motor shaft or pin when assembling or
disassembling.
3. Fix Front Guard
●Hold the rear guard and press the front guard
toward the rear guard from the top, making sure
that the whole periphery of the front guard clicks
into the rear guard.
●Clip the front and rear guard together
with the clip on the guard.
Attention:
● If the front guard is not clipped together
firmly enough, the front guard may come off, causing injury.
How to Take off Front Guard
Unplug first and stop the ratation of the fan blade. Then undo the clip and pull the
grip on the guard ring, pressing the front guard down.
Attention: Do not pull by the clip. May damage the clip.
P5-14606

How to Operate
ON/OFF Operation On/Off
SPEED LOW - MID - HIGH
TIMER Set TIME (0.5-1-2-4-stop timer function) hours
COMFORT Set Comfort mode
Ready
Insert the power plug into a 120V power point.
Start
Switch on by pushing [ON/OFF] button.
(The fan starts at the speed “LOW” )
Pushing [ON/OFF] button again to end the operation.
Speed setting
Select your preferred fan speed by pushing [SPEED] button.
LOW–MID-HIGH
(Each press will change the speed and the speed indicator lamp)
Timer setting
Select at your desired time (0.5-1-2-4 Hour) by pushing [TIMER] button.
0.5 – 1 – 2 – 4 – stop timer function
(Each press will change the time and the time indicator lamp)
After the time you set, the fan will stop automatically.
Rhythm mode setting
Set Rhythm mode by pushing [RHY] button. Push it again, Rhythm mode is
canceled.
(Each press will change the mode and the Rhythm indicator lamp)
CAUTION:
● Do not cover remote control reception area.
(If there is any obstacle between the reception area and the remote control, the
remote control will not work)
● Handle remote control carefully. Do not drop, step on, or spray water on the
Remote control.
(May damage or break.)
TiltingAdjustment
Always switch the fan off before making a tilt adjustment. The air flow can be
P6-14606
P7-14606

adjusted upward or downward simply by moving the guard up or down.
CAUTION: In the case of no blades installed, please don't run the product.
Operating Block Diagram Analysis
Rhythm Mode:
At Low Speed:
At Mid Speed:
At High Speed:
Maintenance and Storage
WARNING
When cleaning, the plug must be removed from the power point. Do not
handle plug with wet hands.
[May cause electric shock or injury.]
Do not press the height adjustment button while the fan and fan guard are
detached.
[The motor section (slide pipe) may jump out of the stand part, causing injury.]
When disassembling the base or stand, unplug plug from the power point.
[May cause electric shock or injury.]
How to Clean
P8-14606
P9-14606

Disassemble the fan and guard in the inverse order of assembling. Wash off dirt
and dust with well squeezed wet soft cloth with water or neutral detergent, then
wipe off the detergent.
CAUTION:
Do not use volatile solvents such as gasoline, thinner, benzene, wax,
kerosene, alcohol, polishing powder, or alkaline detergent. These may
discolour or damage the machine, causing injury.
If using a chemical dust cloth, follow those instruction.
Do not oil plastic parts. May cause discoloration or injury from damaged parts.
How to Store
Disassemble fan, guard, stand and base in the inverse order of assembling.
Clean the motor shaft and oil put the motor shaft cover back to the motor shaft.
Store these parts in the box provided at purchase and keep in a dry place.
CAUTION:
When the fan is not facing front, do not force the fan to turn. Use the swivel
function.
Clean the fan and guard referrring to [ How to Clean], then store it.
How to Disassemble the Base
1. Put the motor shaft upward, then unscrew fixing ring by turning anticlockwise.
(Refer to the drawing at below)
Holding the base firmly, then pull the base.
CAUTION:
If the motor shaft is facing downward, the fan will become unstable and may
damage the product or floor.
When putting the motor shaft down, the fan is unstable. May cause machine
failure and damage to floor.
2. Hold the stand firmly and gently lift and remove the base.
Technical Specifications
V
oltage 120V~60Hz Power Consumption ?A or ?W
Fan Speed
Time
r
Product Holde
r
Join-One Electric (Shenzhen) Co.,Ltd
Subject to technical modification
P10-14606
P11-14606