HomePro ZTH200 User manual

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
1
User Manual
for
HomePro ZTH200
Wireless Controller
Version 1.26
RF Home Automation

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
2
Note: This module must be “Included in the
Network” only where it will be permanently
installed. The proper operation of this node in the
mesh network is dependent on it knowing its
location with respect to other nodes. You cannot
“test bench” configure this module.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
3
Radio Frequency Wireless Controller, Version 1.26
ALL OFF Button
(Turns all included
modules OFF)
OK Button
(Accepts selection)
Navigation Buttons
(Scroll left or right through menus)
Scene Button
(Brings up scene menu)
Numbered Speed Buttons
(Quick access to groups and scenes)
Clear Button
(Cancels actions)
ALL ON Button
(Turns all included
modules ON)
Menu Button
(Activates menu display)
ZTH200
RF Home Automation
BEFORE YOU BEGIN...
READ ALL INSTRUCTIONS
Remove battery cover on rear of control. Install two (2) AA alkaline batteries (included).
There are no field repairable assemblies on this unit. For warranty and general product information visit our web site at www.act-
solutions.com. If service is needed, the unit must be returned where purchased.
BUTTON LAYOUT
MENU ......................................... ACTIVATES THE MENU DISPLAY.
OK .............................................. ACCEPTS CHOICES ON THE DISPLAY.
LIGHT BULB (SOLID) ............... ALL MODULES ON.
LIGHT BULB (w/ SLASH) ......... ALL MODULES OFF.
LEFT ARROW ........................... MENU NAVIGATION BUTTON, LEFT.
RIGHT ARROW ......................... MENU NAVIGATION BUTTON, RIGHT.
C................................................ CLEAR. CANCELS ACTIONS.
S................................................. SCENE BUTTON. TURNS SCENES ON/OFF (THESE ARE GROUPS OF
MODULES & DIM SETTINGS PREDETERMINED BY USER).
“1” TO “6” ............................... SPEED BUTTONS. QUICK ACCESS TO USER DEFINED GROUPS AND SCENES.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
4
WIRELESS CONTROLLER
This user manual is designed to guide
you through the setup and features of
the HomePro Z-Wave Lighting and
Appliance Control System. You will be
amazed at the possibilities for control.
You can easily enhance the comfort and
security of your home or office. You’ll
see how easy it is to quickly create a
totally customized system that can
remotely control lamps and appliances
without costly professional installation...a
system that any do-it-yourself person
can easily handle.
For example, with just one Wireless
Controller you can control up to 64
individual lamp units or wall switches!
You can control a single receiver, in
groups, or all receivers at once. You can
turn on custom programmed mood
lighting and use timers for lighting as a
burglar deterrent.
This user guide tells you how to create
your system. Instructions for installation
and setup of built-in components (wall
switches, dimmers, etc.) are included
with those components.
The HomePro Z-Wave Lighting and Appliance Control System
gives you the following functionality.
Safety and Security
•All OFF/ALL ON
On the way out you can turn off all lights in the house with one button.
At night, if you hear noises, you can turn all lights in the house on from
your bedroom.
•Timers
Let the clock control your lamps and appliances so they automatically
turn on and off at preset hours. You won’t ever have to come into a
dark house again.
Comfort
•Remote Control
Control your lights wirelessly from the sofa, the bed, the kitchen or
wherever you are.
•Grouping
No more wandering from lamp to lamp. Control groups of lamps
simultaneously with one button.
•Scenes
Create and save custom lighting scenes for special occasions like
dinner parties, TV watching, romantic atmosphere, book reading, etc.
•Dimming
Dimming lights with the HomePro Control System saves on electric
bills.
•Thermostat Control
Switch from Heating to Cooling modes and adjust setpoint from your
easy chair.
RF Home Automation
FullCoverage plus added communication with Version 1.26
One of the key features of the HomePro Z-Wave is the fact that Z-Wave automatically routes the signal from one device to the next,
effectively going around obstacles and radio dead spots in your home or office. You only need to be within 100 feet of any HomePro
Z-Wave device to communicate with all other HomePro Z-Wave devices, so the more HomePro Z-Wave enabled devices you have
in your home or office, the better the coverage and the more reliable the network becomes.
New software features (Version 1.26) allow changing the factory configuration of devices and reviewing the settings. In addition it
allows association of a device with other specific devices and a review of those associations. The software version of any
HomePro ZTH200 can be verified by going to: Setup Menu/Reset Remote Control/Factory Default/press ALL LIGHTS OFF button.
The ZTH200 allows most devices into a group so they can be controlled by the remote. The device types that will specifically not
be added to a group (though they will be added to the Z-Wave system) are the following: Thermostat Controller, Repeater Slave,
Binary Sensor, Multilevel Sensor, Pulse Meter, Entry Control and Non Interoperable.
The types listed above will not be controlled by the remote because they either have nothing to control or do not support the BASIC
COMMAND which the remote uses to turn devices on and off. Device ID is shown when the device is added to the network.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
5
SYSTEM DESCRIPTION
The HomePro product line from Advanced Control Technologies includes several products that are intended to work together to
provide convenient control of all of your home lighting and appliances. By using the ZTH200 Wireless Controller, all of these
HomePro devices are linked by a state of the art wireless communications network featuring patented Z-Wave technology. This
technology insures that the commands that you give through the Wireless Controller are reliably communicated by radio frequency
to the intended HomePro device.
The Wireless Controller operates up to 64 HomePro devices, which include both plug-in and wall mounted dimmers and switches.
The Wireless Controller finds a way to route your commands to the intended device through other HomePro dimmers and switches.
This is possible because each of these devices are designed to retransmit the commands that are sent through them to adjacent
devices that might otherwise be out of range of the Wireless Controller. The Z-Wave system provides that a command can be
routed if necessary through as many as four different devices in route to the intended device.
Communication with devices employing Z-Wave technology is bidirectional. That is, when a command is sent from a Wireless
Controller, an acknowledgment is sent back to it by the affected devices to confirm that thecommand was received (not necessarily
that the load changed state). In the unusual situation in which a command is not properly received, a message will appear on the
Wireless Controller’s display to inform the User.
Introduction to HomePro Products
This controller is designed to work with the HomePro products shown. Most other Z-Wave modules of other device classes can be added to
the system and will also act as repeaters if they support this functionality..
ACT # Product Description
ZDP200 Dimmer, 300W, 230 VAC, Plug-in, Euro plug (Netherlands etc.), Ivory
ZRP200 Relay, 10A, Plug-in, 230 VAC, Euro plug (Netherlands etc.), Ivory
ZDP210 Dimmer, 300W, 230 VAC, Plug-in, UK plug, Ivory
ZRP210 Relay, 10A, Plug-in, 230 VAC, UK plug, Ivory
ZDP230 Dimmer, 300W, 230 VAC, Plug-in, French plug, Ivory
ZRP230 Relay, 10A, Plug-in, 230 VAC, French plug, Ivory
ZCS010 Transceiver-Controller, RS232 Interface - Euro Frequency (power supply not provided)
ZCU010 Transceiver-Controller, USB Interface - Euro Frequency, hub powered
ZCU011 Transceiver-Controller, USB Interface - Euro Frequency (power supply not provided)
ZTT000 Thermostat, 24V, Wall mount, Euro Frequency, White
ZIR010 Transmitter, PIR, Wall mount, Battery Operated, Euro Frequency, White
ZTH200 Transceiver, Wireless Controller
ZDP200
Plug-in Dimmer
ZDP210
Plug-in Dimmer
ZDP230
Plug-in Dimmer
ZIR000
PIR Occupancy &
Security Sensor

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
6
Table of Contents
1. INTRODUCTION PAGE
1.1 Getting Starte d................................................................................................................ 7
2. TIME
2.1 Setting the Tim e...................................................................................................................... 7
3. GENERAL OPERATION
3.1 Wireless Controller software features..................................................................................... 7
3.2 Power Down and Display Time-out......................................................................................... 7
4. HOW TO USE THE ZTH200 FEATURES
4.1 Menu navigation and selection ............................................................................................... 7
4.2 Groups/Scenes............................................................................................................. ........... 7
4.2.1 Add module to Group.............................................................................................................. 9
4.2.2 Add module to Scene. ............................................................................................................ 9
4.2.3 Exceeding module limit........................................................................................................... 10
4.2.4 Adding unsupported device types to the network................................................................... 10
4.2.5 Name a Group/Scene.............................................................................................................. 10
4.2.5.1 Character set........................................................................................................................... 10
4.2.6 Remove module from Group/Scene................................................................................ ........ 11
4.2.7 Delete Group/Scene....................................................................................................... ......... 11
4.3 Timer ...................................................................................................................................... . 12
4.3.1 Create/Edit a Timer ................................................................................................................ 12
4.3.2 Delete Timer .......................................................................................................................... 14
4.4 Add Thermostat....................................................................................................................... 14
4.4.1 Requesting Data from Thermostat.......................................................................................... 14
4.4.2 Changing Thermostat Settings................................................................................................ 14
4.4.3 Thermostat Modes.................................................................................................................. 15
4.4.4 Thermostat Set Point................................................................................................................ 15
4.4.5 Fan Modes............................................................................................................................... 15
4.5 Removing Thermostat............................................................................................................. 16
4.6 Setup....................................................................................................................................... 16
4.6.1 Association.................................................................................................................... ........... 16
4.6.1.1 Assign Route.................................................................................................................... ........ 18
4.6.2 Config Unit Menu..................................................................................................................... 18
4.6.3 Display contrast ...................................................................................................................... 19
4.6.4 Setup All On/Off ..................................................................................................................... 19
4.6.5 Copy configuration to another Wireless Controller.............................................. .................. 20
4.6.5.1 Sending information to another Wireless Controller................................................................ 21
4.6.5.2 Receive information from Master Wireless Controller....... ..................................................... 22
4.6.6 Resetting Modules (plug-in lamp, appliance and wall mount.................................................. 22
4.6.7 Reset Wireless Controller....................................................................................................... 23
5. OPERATION MODE
5.1 Operation display.................................................................................................................... 23
5.1.1 Secondary wireless controller indication................................................................................. 23
5.1.2 Scene indication...................................................................................................................... 23
5.1.3 Low battery indication.............................................................................................................. 24
5.2 Using operation mode............................................................................................................. 24
5.2.1 Controlling groups using speed buttons.................................................................................. 24
5.2.1.1 Pressing a speed button briefly. ............................................................................................. 24
5.2.1.2 Holding a speed button down.................................................................................................. 25
5.2.2 Controlling groups using navigation buttons............................................................................ 26
5.2.3 Controlling scenes .................................................................................................................. 26
5.2.4 All ON/All OFF ........................................................................................................................ 26
6. OTHER INFORMATION
Other Z-Wave devices and Warranty...................................................................................... 27
FCC and IC Notice ................................................................................................................. 27

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
7
1. INTRODUCTION
1.1 GETTING STARTED
Congratulations on your purchase of the ZTH200 and other HomePro components. This manual will guide
you in understanding the full capabilities of the HomePro System and operation of the Wireless Controller.
Remove battery cover of ZTH200 Controller and install two AA batteries noting the correct direction.
2. TIME
2.1 SETTING THE TIME
To set time, begin by pressing “MENU” button.
Note: Use arrow buttons to scroll though hours and minutes
3. GENERAL OPERATION
3.1 WIRELESS CONTROLLER SOFTWARE FEATURES.
• Provides user level control for 64 modules (i.e. one module, one group).
• Allows configuring of 64 groups.
• Eight (8) timers are available to the user. Each timer can be used to control any one of the existing groups.
• Displays the time in 12 hour AM/PM format.
• Allows multiple wireless controllers (one master and one or more secondary ones) in various locations for
convenience.
• Allows multiple Wireless Controllers “Each wireless controller comes pre-programmed from the factory with a
unique Home ID. This ID prevents unintended access to a user’s network of modules by neighbors or others
who may also be using HomePro products. If a user desires to add additional controllers to their HomePro
network however, there is a provision to allow this to be done without compromising this important feature
(see section 4.6.5).”
3.2 POWER DOWN AND DISPLAYTIME-OUT
The ZTH200 goes into a power saving mode after a period of inactivity in order to conserve battery life.
Pressing any button will cause the unit to “wake up” and process any of your commands. The display is
blank in the power down mode.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
8
4. HOW TO USE THE ZTH200 FEATURES
4.1 MENU NAVIGATION AND SELECTION
Pushing the “Menu” button will activate the menu display.:
a. and buttons are used to navigate through the menu. All menu levels wrap
around.
b. activates the currently selected menu item and recalls information from thermostat.
c. (or Clear) cancels the currently selected item and will in most instances step back to the
previously selected menu level. If used from top menu level the Controller will return to clock
display.
The top menu level behaves like this: Using the right and left arrow buttons you can toggle right or left through the menu
selections of : GROUPS
SCENES
TIMER
SETUP
THERMOSTAT
Top level menus wrap around, so arrow buttons in any direction will repeat menu selections. Push OK or C button to
activate display if asleep (blank).
Select any one by pressing OK. Follow instructions to set up that function (explained in following paragraphs). Using
the Clear button (C) at any time will take you back to the Time (which will auto-off after 5 seconds).
4.2 GROUPS/SCENES
The layout and behavior of the “groups” and “scenes” menus are very similar. Where they are identical, “groups” is used
as an example. Push OK or C button to activate display if asleep.
To select groups from 7 to 64 or scenes from 7 to 32 see page 28, section 5.5.2 and 5.2.3.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
9
4.2.1 ADD MODULE TO GROUP
Adding a module to a group using the menu is done
this way:
A group is a set of one or more modules that are
to be operated together as if they were one
device. More specifically, every module that is
included in a group will switch on or off together
as that group is turned on and off. When a group
is activated, each Lamp Module in that group
turns on, returning to its last dim level – a level
that in general, will differ from module to module.
Appliance Modules may also be included in
groups. A module must be “Included in the
Network” only where it is permanently
installed, not at a test bench.
Alternatively if the group has been named, the name
shows up instead of the number. To add more units
repeat the procedure “ADD UNIT TO GROUP”. Groups
and scenes may each be given user-defined names.
See section 4.2.5 for instructions on how to do this.
4.2.2 ADD MODULE TO SCENE.
Adding a module to a scene is done this way:
Note: A Lamp or Appliance Module may be in-
cluded as a member of several different groups,
several different scenes, or several groups and
scenes.
Note: All of the properties of groups and scenes
also apply to HomePro wall dimmers and switches.
A scene is a combination of one or more modules, except that the controller stores not only the combination, but
also the desired dim level for each Lamp Module. The dim level is stored at the time that a Lamp Module is added
to a scene. Consequently, when a scene is activated, the Lamp Modules will all go to their previously defined dim
levels regardless of what their most recent dim level may have been. Some modules may get brighter while others
may be pre-programmed by the user to become dimmer. Because Appliance and Wall Switch Modules are switch-
ing devices, they will either be defined as on or off when added to a scene.
Note that hitting “C” will not clear units that have already been stored in the selected scene. A module is stored in a scene
when “UNIT INCLUDED” is shown in the display.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
10
4.2.3 EXCEEDING MODULE LIMIT.
This ZTH200 Controller supports up to 64 modules. If the user tries to add more than 64 modules to a group or scene this
message will be displayed:
However the module will be given a valid ID and it will be used as a repeater if it supports this functionality, but it cannot
be directly controlled by this ZTH200 Wireless Controller. If a secondary Wireless Controller which handles more than
64 modules (could even be HomePro’s USB to RF controller) is set up using this Wireless Controller, then the module
will be made available for control in that secondary controller.
4.2.4 ADDING UNSUPPORTED DEVICE TYPES TO THE NETWORK
Devices of other types such as Remote Controller, Static Controller, Thermostat Controller, Repeater Slave, Binary
Sensor, Multilevel Sensor, Pulse Meter, Entry Control and Non Interoperable; they just cannot be controlled by this
ZTH200. If the user adds an unknown device to the network this information will be displayed:
4.2.5 NAME AGROUP/SCENE
To name a group or scene enter the relevant menu. Then select the group/scene name to be edited.
In order to delete a name, just select the group/scene and clear the old name using “C”.
Note: Outlined area indicates “blinking” cursor.
4.2.5.1 CHARACTER SET.
The characters available for naming are: ‘A’,’B’,’C’,’D’,..,’Z’, and ’0',’1',’2',..,’9',’ ‘
Note that no lower case letters are available to the user.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
11
4.2.6 REMOVE MODULES FROM GROUP/SCENE.
Clear cancels the current selection. Navigation buttons only work if more than one group or scene exists.
4.2.7 DELETE GROUP/SCENE
Scroll left or right to find scene.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
12
If no active groups or scenes exists the following occurs:
4.3 TIMER
The timer menu consists of the following menus:
Timer information is stored in the Wireless Controller – not in the module.
4.3.1 CREATE/EDIT ATIMER
There are eight timers available for the user. Each timer controls one of the existing groups as chosen by the user.
If an existing timer is selected that timer will be edited. Pressing the clear button will cancel the editing and leave the
timer as it was. The time indicated when selecting a timer is the start time of that timer.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
13

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
14
4.3.2 DELETE TIMER
When a timer is no longer needed it can be deleted using “Delete a timer” menu.
4.4 ADD THERMOSTAT
The ZTH200 will support only one (1) thermostat. If more than one (1) thermostat needs supported, then more ZTH200’s
will be required.
Scroll to the Setup Menu and Press OK.
Scroll to “Add Tstat To Network” and Press OK.
ZTH200 will prompt “Press Button On Unit”.
Once thermostat is added, the ZTH200 will show “Tstat Incl’d, with Support” .
This indicates that the thermostat was included into the Z-Wave network and that the ZTH200 was able to retrieve the
modes and set points the thermostat supports.
If the remote only shows “Thermostat Included” or “T’stat Incl’d, w/No Support” then the supported modes and set
points were not received from the thermostat and the ZTH200 will not allow the user to access all of the thermostat
functions. If this occurs, simply add the thermostat to the ZTH200 again until it shows “Tstat Incl’d with Support”.
4.4.1 REQUESTING DATAFROM THERMOSTAT
After the thermostat has been included into the ZTH200, repeatedly pressing the OK button will cause the ZTH200 to
toggle between showing the actual temperature (if the thermostat supports sending actual temperature), current mode
and current set point of the mode, and fan mode (if the thermostat supports fan modes),
4.4.2 CHANGING THERMOSTAT SETTINGS
Scroll to Thermostat and Press OK.
You will see Thermostat Mode. At that point you could scroll left or right to change Set point or Fan Speed.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
15
If instead you press OK, you will be directed to the thermostat modes of control (i.e.. Cooling, Heating, etc.).
In each case, the remote will retrieve the current setting of the thermostat and then allow you to change that setting
(depending on what is supported by the thermostat).
4.4.3 THERMOSTAT MODES
The ZTH200 supports HEAT MODE, COOL MODE, AUTO MODE, AUTO CHANGEOVER MODE, DRY AIR MODE,
FAN MODE ONLY, FURNACE MODE, MOIST AIR MODE. Scroll left or right to select. After you have changed the
setting, press OK.
If setting was recorded, display will say “Mode Successful”. If not it will say “Comm. Failed”, in which case reorient
the ZTH200 and try again.
4.4.4 THERMOSTAT SETPOINT
The ZTH200 supports sending set points from 55
o
F to 90
o
F and from 12
o
C to 32
o
C. Scroll left or right to select desired
set point.
The ZTH200 will display set points from 40
o
F to 90
o
F or from 4
o
C to 32
o
C. Above and Below those limits and the ZTH200
will display > Max or < Min. After you have changed the setting, press OK. If setting was recorded, display will say
“Setpoint Successful”. If not it will say “Comm. Failed”, in which case reorient the ZTH200 and try again.
4.4.5 FAN MODES
The ZTH200 supports FAN MODE AUTO (high), FAN MODE ON (high), FAN MODE AUTO (low), FAN MODE ON
(low). Scroll left or right to select. After you have changed the setting, press OK.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
16
4.5 REMOVING THERMOSTAT
To Remove Thermostat from Network, Scroll to Setup Menu, Choose “Reset Unit” and Press OK. (See Setup Menu
4.6).
4.6 SETUP
The setup menu is used to access system functions. The layout is as follows:
4.6.1 ASSOCIATION MENU
Allows you to associate other units to a module that supports this feature.
When you select “Associate Units” above, the following menu will appear:
ADD ASSOCIATION
Used when you want to associate one unit to another unit. The term associate means linking two units so that one unit
will send information to the other unit. The unit doing the sending is the source and the unit receiving the information
is the destination. If the modules are not within range of one another, refer to “Assign Route” below.
When you select Add Association, you will be prompted to select a group number as shown below:
This group number is the group within the source module in which the destination module will be placed when associated.
What each group is sent and does is solely dependent upon the source module. Refer to the instructions that came
with the source module.
Once the group number is selected (using the arrow buttons), press OK.
Now you will be prompted to “Press Button on Destin.”. This indicates you should now press the button on the
destination module. Refer to instructions of destination module on exactly what to do in this situation as you may have
to do more than simply pressing a button.
When the ZTH200 receives the destination module ID, it will then request you to “Press Button on Source”. Refer to
instructions of source module on exactly what to do in this situation as you may have to do more than simply pressing
a button.
After you have pressed the button on the source, the ZTH200 will either show “Successful” or “Comm. Failed”. If the
ZTH200 shows “Comm. Failed”, simply try again or move closer to the source module and try again.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
17
REMOVE ASSOCIATION
Used when you want to remove an association in a unit . The unit in which the association is removed is the source
module and the unit being removed is the destination module. When you select “Remove Association”, you will be
prompted to select a group number.
What each group does is solely dependent upon the source module. What each group is sent is also dependent upon
source module. Refer to the instructions that came with the source module.
Once the group number is selected (using the arrow buttons), press OK.
Now you will be prompted to “Press button on Destin.”. This indicates you should now press button on the destination
module. Refer to instructions of destination module on exactly what to do in this situation as you may have to do more
than simply pressing a button.
When the ZTH200 receives the destination module ID, it will then request you “Press Button on Source”. Refer to
instructions of source module on exactly what to do in this situation as you may have to do more than simply pressing
a button. After you have pressed the button on the source module, the ZTH200 will either show “Successful” or
“Comm. Failed”. If the ZTH200 shows “Comm. Failed”, simply try again or move closer to source module and try
again.
REQUEST ASSOCIATION
If you desire to determine what modules a source module sends to, this function will allow you to determine that
information.
When you select “Request Association”, you will be prompted to select a group number.
This group number is the group within the source module in which the destination module will be placed in when
associated. What each group is sent and does is solely dependent upon the source module. Refer to the instructions
that came with the source module.
Once the group number is selected either using the arrow buttons, press OK.
Now you will be prompted to “Press Button on Unit” . Refer to instructions of module on exactly what to do in this
situation as you may have to do more than simply pressing a button.
When the ZTH200 receives the information from the unit, the ZTH200 will either show:
Use the arrows to show the units in the group.
Or it will show:
Which indicates the group is empty in the ZTH200.
Pressing the OK button at this point will also show you how many modules the group can support.
If the ZTH200 requests the association settings but does not receive information from the unit, the ZTH200 will simply
show “Request Sent” until the ZTH200 receives the information, goes to sleep, or you press the CLEAR button.

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
18
REQUEST TOTAL GROUPS
Although typically this information would be provided in the slave modules instructions, this function will allow you to
determine how many groups a device supports.
When you select “Request Total Groups”, you will be prompted to “Press Button On Unit” . Refer to instructions
of unit on exactly what to do in this situation as you may have to do more than simply pressing a button.
After you have done so, the ZTH200 will show:
where N is the number of groups in the ZTH200.
Also, if the ZTH200 requests the total groups a unit supports but does not receive information from the unit, the ZTH200
will simply show “Request Sent” until the ZTH200 receives the information, goes to sleep, or you press the CLEAR
button.
4.6.1.1 ASSIGN ROUTE
When two devices are not within range of one another, then a route can be assigned to the source module (the device
sending the information). This is dependent upon whether the source module is a normal slave or a routing slave. It must
be a routing slave (The routing slave can host a number of routes to communicate with a slave or controller but the normal
slave is typically a device that only receives input and reports status if polled). Again, the unit doing the sending is the
source module and the unit receiving the information is the destination module. Also of note, some routing slaves only
hold routes to one module, while newer routing slaves can hold routes to up to 5 modules. Refer to instructions that came
with device.
When you select “Assign Route”, you will be prompted to “Press Button On Destin.”. Refer to instructions of
destination module on exactly what to do in this situation as you may have to do more than simply pressing a button.
When the ZTH200 receives the destination module ID, you will be prompted to “Press Button On Source”. Refer to
instructions of source module on exactly what to do in this situation as you may have to do more than simply pressing
a button. After you have pressed the button on the source module, the ZTH200 will either show “Successful” or
“Comm. Failed”. If the ZTH200 shows “Comm. Failed”, simply try again or move closer to source module and try
again.
Note that units may still be unable to communicate to one another if there are no other modules that can communicate
to both the source and destination module.
DELETE ALL ROUTES
Removes all routes that were previously assigned to a routing slave.
When you select “Delete All Routes” , you will be prompted to “Press Button On Unit” . Refer to instructions of module
on exactly what to do in this situation as you may have to do more than simply pressing a button.
After pressing button, the ZTH200 will then show “All Successful” or “Comm. Failed”. If the ZTH200 shows “Comm.
Failed”, simply try again or move closer to module and try again.
4.6.2 CONFIG UNITS MENU
Allows you to send/receive configuration settings to a Z-Wave unit that supports such functionality.
When you select “Config Units” , the following menu will appear:

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
19
SET CONFIG
Allows you to set configuration settings to a unit that supports such functionality. When you select “Set Config”, you
will be prompted with
Consult the instructions that came with the unit you are configuring as to what each parameter number configures.
After selecting parameter number (use the arrow buttons to change parameter number, then press OK), you will be
prompted:
At this point, you will have to again consult the instructions for the unit you are configuring for information on how many
bytes the parameter being set contains. Then press the 1, 2, or 4 button accordingly. At this point you will be
prompted:
Use the arrow buttons to select value, then press OK.
If you have selected 2 or 4 bytes, when asked “# of Bytes” , you will be prompted for ConfigValue 2 and if necessary
ConfigValue3 and ConfigValue4.
After selecting the value(s) you will be prompted to “Press Button On Unit” . Refer to instructions of unit on exactly what
to do in this situation as you may have to do more than simply pressing a button.
After doing so, the ZTH200 will show “Successful” or “Comm. Failed”. If the ZTH200 shows “Comm. Failed”, simply
try again or move closer to unit and try again.
4.6.3 DISPLAYCONTRAST ADJUSTMENT
“C” cancels the contrast adjustment and returns to idle.
Default contrast is 50% which is restored whenever the
batteries have been removed and reinstalled.
4.6.4 SETUP ALL ON/ALL OFF
Using this menu it is possible to customize the way ALL ON/ALL OFF works. Units can be included or
excluded from all on/off commands (refer to instructions of the devices you are controlling to determine if it supports
this feature).

ZTH200 Operating Instructions (Version 1.26)
P/D 102406
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
20
Setting a device to “Exclude All On Only” will cause the Z-Wave device to
respond to All Off commands but not the All On command.
Setting a device to “Exclude All Off Only” will cause the Z-Wave device to
respond to All On commands but not the All Off command.
4.6.5 COPY REMOTE CONTROL TO ANOTHER WIRELESS CONTROLLER.
This menu is used to copy information from the Master Wireless Controller to other controllers, so that they may
command modules known by the Master Wireless Controller.
Note: The master controller must be the controller used to include new modules to the network and to reset modules.
A replication of the master controller is done as follows:
1. Select “Receive information” on the controller which should receive the information (i.e. the Secondary
Wireless Controller)
2. Select “Send information” and either “Identical copy” or “Only system information” on the controller that is
to send the information (i.e. the Master Wireless Controller).
3. Wait until transmission is completed and both the wireless controllers return to clock display.
4. If a transmission error occur. Please repeat from Step 1.