Honeywell ImperLED E User manual

GB
ImperLED E
Addressable CBS Emergency Light
Dimensional Drawings:
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
Installation:
Step 2: Place a flat blade screwdriver and pull up gently the reflector.
Step 4: Set the module address. For more information about module settings see the next page.
Step 1: Place a flat blade screwdriver and pull up gently the diffusor’s clips from both sides to remove the
diffusor.
Step 3: Install the plastic base with the included mounting screws and plugs. If the hole that exists is not
useful, drill another hole on one of the designated positions in order to pass the cables and install
the included gasket (verify that are not deformed).
Step 5: Always use in any case round mains cable, with a diameter of 5-10mm. ATTENTION!! The cable
must not be deformed in any way (This requirement is important to ensure the IP rating). Make a
hole in the center by using a small screwdriver. Pass the round cable through the gasket.
Step 6: Connect the mains cable to the respective terminal block: L for live wire, N for neutral. Install the
included tie (if needed) to fasten securely the power cables. Power supply cables cross section
2
should be 0.8 – 3 mm .
Step 7: Refit carefully the removed parts (Step 1 & 2). The diffusor must be secured (click sound). This
requirement is important to ensure the IP65 rating.
2
5
1
4
3
N
L
PE
6

GB
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
Pictogram Installation
Mounting Methods
Mounting Accessories (Available After Request)
Step 3: Fill in, the letter G on the specification label.
Step 1: Place a flat blade screwdriver and pull up gently the diffusor's clips from both sides to remove the
diffusor.
Step 2: Install the pictogram you need in the diffusor and refit it to the luminary. (In case you need to
change the pictogram follow the same procedure.)
ImperLED luminaries can be surface mounted on walls or ceilings.
1
Z
G
Wall
bottom
view
Wall installation
290405.11 ImperLED Suspended Pictogram 290471 ImperLED Wall Bracket
Ceiling installation
Ceiling

GB
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
Weight:
Technical description
Part no.:
Lumen output:
o
-30 to 60 C
Up to 95%
Produced in accordance with:
Ambient Temperature Range:
Maximum Power Consumption:
Operation Voltage:
780 gr
Relative Humidity:
At the end of their useful life the packaging and product should
be disposed of via a suitable recycling centre.
Do not dispose of with your normal household waste.
Do not burn.
NOTE! The light source is non-user replaceable.
The light source contained in this luminary shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
ImperLED E Combi SET-30 IP65 230V w/pict
3.8W / 4.2VA
100-240V AC/DC, 50-60 Hz
138002.S30
350 lm
IP65
Degress of cover protection:
Technical lifetime (light source): > 100000 hours
EN 60598-1, EN 60598-2-22, EN 55015
EN 61547, EN 61000-3-2, EN 61000-3-3

GB
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
MODULE FOR SINGLE LAMP SELECTION AND MONITORING
Switching of one selected light in the electric circuit
SET010 select
DIP-switch 1
ON for non-maintained mode
OFF for maintained mode (Default)
DIP-switch 2
OFF for lighting address 1-16 (Default)
ON for lighting address 17-32
Indicator LED
Rotary coding switch
for setting the exact lamp adress DIP-switch 3 (OFF)
Attention!
Connect L and N correctly!
Exchanging L and N causes malfunction.
The address range 17 to 32 can be selected by setting DIP switch 2 to ON.
By means of a suitable control, it is possible with the aid of the SET010 select to determine whether the
lamp connected to it is ready for use or faulty.
Function
In the mixed operation circuit, the connected lamp can also be additionally set in non-maintained mode
or maintained mode (DIP Switch 1).
Settings
Setting the lighting address is carried out by a rotary coding switch that is easily accessible from the
outside.
Lighting addresses 1 to 16 can be slected when DIP switch 2 is set at OFF.
The module is already prepared for administering a total of 32 lighting addresses.
(DIP switch 2 = ON and rotary coding switch = 1 is equivalent to lighting address 17 etc.)
Technical description
Cross section:
Temperature:
Dimensions (L x W x H in mm) 78 x 30 x 20
2
Max: 1.5mm
-30°C up to +60°C, T =+75°C
cmax
SET010 select
Prewired