Honeywell CT30 Series User manual

CT30/CT33
Low-voltage Thermostat
Owner’s
Manual
Getting started
Before you begin, make sure you have:
• Screwdriver
• Hammer
• Level (optional)
• Pencil
• Drill bit (3/16” for drywall, 7/32” for plaster)
Caution cardWire labels
Wall anchors and
mounting screws
(2 each)
CT30/CT33 thermostat Cover plate
Check to make sure your package includes the following items:
® U.S. Registered Trademark. Patents pending.
Copyright © 2005 Honeywell International Inc.
All rights reserved.

Owner’s Manual
2
Remove your old thermostat
1TTuurrnnooffffppoowweerrat heating/cooling system (or fuse/circuit-breaker panel).
2 Remove cover and thermostat, but leave wallplate with wires attached.
Old thermostat
Leave wallplate in place Is there a sealed tube containing mercury?
If so, see mercury notice below.
Cover
MERCURY NOTICE: Do not place your old thermostat in the trash if it contains
mercury in a sealed tube. Contact your local waste management authority for
instructions regarding recycling and proper disposal.
Did you purchase right thermostat? Count wires to check.
Count the number of wires coming out of the wall and attached to terminals in
your old thermostat. If any of them are attached to a terminal marked “C”or “C1”
do not count that wirein your total.
If the total (not counting C or C1) is 2 wires, proceed to the next page. If you have
3 or more wires, your new thermostat may not be compatible with your system.
Stop installation and call 1-800-468-1502 for advice.
Do you have 3 or more wires? If so, stop now.
You may have purchased the wrong replace-
ment thermostat.

CT30/CT33 Low-voltage Thermostat
3
Label wires and remove old wallplate
Use a screwdriver to disconnect wires one by one.As you disconnect each wire,
wrap it with the label matching the letter on your old thermostat. (Adhesive labels
are supplied in your thermostat package.)
Remove the old wallplate only after all wires are labeled. Be careful not to let
loose wires fall into the wall opening.
Wrap supplied labels securely around each wire
Do not let wires fall into wall opening!
IGNORE WIRE COLORS: Use only letter designations
to identify wire types.
Mark mounting position
1Level base or cover plate
if desired.
2Mark positions of
both screw holes.

Owner’s Manual
4
Wire connections
1Match each labeled wire
with same letter on terminal.
2Use a screwdriver to loosen
screw terminals, wrap bare
wire securely around termi-
nals, then tighten screws.
3Push any excess wire back
into the wall opening.
Labels don’t match?
If labels do not match letters on
thermostat, see table below.
Mount thermostat base
1Drill holes at pencil-marked locations (3/16” holes for drywall, 7/32” holes for plaster).
2Use hammer to
tap anchors into
holes until flush
with wall.
3[Optional] Pull
wires through
cover plate (if
needed to cover
marks left by your
old thermostat).
4Connect wires first
(see below), then
insert screws.
Check level if
desired, then
tighten screws.
Thermostat base
Optional cover plate
Back of thermostat base
Existing wires Connect to:
R•RH •4•VTerminal “R”
W•W1 •HTerminal “W”
Y•Y1 •M Stop! See note
G•F Stop! See note
Rc Stop! See note
If any of these wires are present, you
cannot use this thermostat with your
system. See page 2.

CT30/CT33 Low-voltage Thermostat
5
Set adjustment lever (CT30 only)
1 Separate cover from thermostat,
and remove the plastic insert.
2 Use a pencil to move the adjust-
ment lever to the proper setting for
your system (see table below).
Finish installation
1Align the 3 tabs on
the cover with slots
on the thermostat,
then push gently
until the cover
snaps into place.
2Restore electrical
power at the heat-
ing/cooling system,
or at the fuse/
circuit-breaker
panel.
Cover
Thermostat
(shown with
optional
cover plate)
Your system Setting
Gas or oil furnace
(less than 90% efficiency) 0.4
Electric furnace (any type) 0.3
High efficiency furnace
(more than 90% efficiency) 0.8
Hot water system 0.8
Gas/oil steam or gravity system 1.2

Owner’s Manual
6
Operation
Temperature setting
Move lever to adjust desired indoor
temperature.
System off (CT33 only)
Move lever to far left to turn
off heating system.

CT30/CT33 Low-voltage Thermostat
7
Limited Warranty
Honeywell warrants this product to be free from defects in the workmanship or
materials, under normal use and service, for a period of one (1) year from the date
of purchase by the consumer. If at any time during the warranty period the prod-
uct is determined to be defective or malfunctions, Honeywell shall repair or
replace it (at Honeywell's option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from
which you purchased it; or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the
determination whether the product should be returned to the following address:
Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley,
MN 55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs.This warranty shall
not apply if it is shown by Honeywell that the defect or malfunction was caused
by damage which occurred while the product was in the possession of a
consumer.
Honeywell's sole responsibility shall be to repair or replace the product
within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY
LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSE-
QUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY
BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF
THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental
or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON
THIS PRODUCT.THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS
WARRANTY. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which
vary from state to state.
If you have any questions concerning this warranty, please write Honeywell
Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-
1502. In Canada, write Retail Products ON15-02H, Honeywell Limited/
Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9.

Need Help?
For assistance with this product please visit www.honeywell.com/yourhome
or call Honeywell Customer Care toll-free at 1-800-468-1502
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
www.honeywell.com/yourhome
Automation and Control Solutions
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.
® U.S. Registered Trademark.
© 2005 Honeywell International Inc.
Patents pending. All rights reserved.
69-1808ES Rev. 03-2005
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
Scarborough, Ontario M1V 4Z9

CT30/CT33
Termostato de bajo voltaje
Manual del
usuario
® U.S. Marque déposée. Brevets en instance.
Copyright © 2005 Honeywell International Inc.
Tous droits réservés.
Lista de comprobación previa a la instalación
Herramientas y materiales necesarios
• Destornillador
• Martillo
• Nivel (optativo)
• Lápiz
• Mecha de taladro (3/16”para mampostería en seco, 7/32” para yeso)
Tarjeta de
advertencia
Rótulos para los cables
Soportes de pared y
tornillos de montaje
(2 cada uno)
Termostato
CT30/CT33
La placa de cubierta
Asegúrese de que el paquete contenga los siguientes elementos:

Manual del usuario
Remueva su viejo termostato
1DDeessccoonneecctteellaaaalliimmeennttaacciióónnen el sistema de calefacción/refrigeración (o en el
panel de fusibles/disyuntor).
2 Retire la cubierta y el termostato, pero deje los cables unidos a la placa de montaje.
Termostato viejo
Deje la placa de montaje en su lugar ¿Existe algún tubo sellado que contenga
mercurio? Si es así, consulte el aviso sobre
mercurio que figura abajo.
Cubierta
¿Compró el termostato correcto? Cuente los cables.
Cuente los cables que salen de la pared y están conectados a los terminales de su
viejo termostato. Si cualquiera de ellos está conectado a un terminal marcado “C”o
“C1” no lo cuente.
Si el total (sin contar CCo CC11) es de 2 cables, continúe con la página
siguiente. Si hay 3 cables o más, es posible que su nuevo termostato no sea
compatible con su sistema. Interrumpa la instalación y llame al 1-800-468-1502
para pedir consejo.
¿Hay 3 o más cables? Si es así, deténgase
ahora. Es posible que haya comprado el
termostato de reemplazo incorrecto.
AVISO DE MERCURIO: No arroje su viejo termostato a la basura si contiene mercurio
en un tubo sellado. Comuníquese con la autoridad local de disposición de desechos
para recibir instrucciones sobre reciclado y eliminación correcta..
2