Honeywell TH114-A-240D User manual

08162 / TH114-A-240D / TL7235 69-2022-1 2007-10-17 1/2
Non-programmable Thermostat - Installation and User Guide
This thermostat can be connected to an electric heater to control the
room temperature.
* The thermostat indicates how much heating is required to maintain the desired
temperature. For example, is displayed when heating is at 40 percent.
The configuration switch is located at the back of the control module
(faceplate). The switch allows you to select between °C and °F
Turn off power to the heating system at the main electrical panel
to avoid electrical shock. The installation should be carried out
by an electrician.
High voltage thermostats must be installed onto an electrical
box.
For a new installation, choose a location about 5 ft. above the
floor and on an inside wall.
The thermostat must be installed on an inside wall facing the
heating system.
Avoid locations where there are air drafts (top of staircase, air
outlet), dead air spots (behind a door), direct sunlight or con-
cealed chimneys or stove pipes.
nConnect the power base wires to the power supply and load
using solderless connectors for copper wires.
oPush the excess length of the high-voltage wires back into the
electrical box.
pSecure the power base to the electrical box using the provided
screws.
qInstall the control module onto the base.
rApply power to heating system.
NOTE: Always keep the thermostat's vents clean and unobstructed.
As soon as the thermostat is powered, it undergoes a
series of tests before displaying the actual temperature.
LO: The measured temperature is below the display
range. Heating is activated.
HI: The measured temperature is above the display
range.
nDescription
1.
Display
% of heating 1 to 24% 25 to 49% 50 to 74% 75 to 99% 100%
oConfiguration
2.
Backlight button
Temperature
adjustment buttons
Set the switch to
Offtocut powerto
the heater
Heating indicator *
Temperature
display
Appearswhen
the setpoint is
displayed
pInstallation
3.
qPower-up
4.
rError Messages
5.
Power
Load
08162
TH114-A-240D
TL7235
400-114-014-B_69-2022-1 (Cadet TL7235) ENG.fm Page 1 Wednesday, October 17, 2007 8:58 AM

08162 / TH114-A-240D / TL7235 69-2022-1 2007-10-17 2/2
Non-programmable Thermostat - Installation and User Guide
The display illuminates for 5 seconds when the backlight button is
pressed. When either of the buttons is pressed, the display illu-
minates for 10 seconds.
The thermostat normally displays the actual temperature. To view the
setpoint, press one of the buttons once. The setpoint will appear
for 5 seconds. To change the setpoint, press one of the buttons
until the desired temperature is displayed. To scroll the setpoint
faster, do not release the button.
Power supply: 208/240 VAC, 50/60 Hz
Maximum load:16 A (resistive only)
3328 W @ 208 VAC
3840 W @ 240 VAC
Setpoint range: 40 °F - 86 °F (5 °C to 30 °C)
Display range: 32 °F - 122 °F (0 °C - 50 °C)
Display resolution: 1 °F (0.5 °C)
Heating cycle length: 15 minutes
Storage: -4 °F to 120 °F (-20 °C to 50 °C)
Remote controller input (ECONO): requires a dry contact
Certifications: CSA/UL
Honeywell warrants this product, excluding battery, to be free from
defects in the workmanship or materials, under normal use and ser-
vice, for a period of one (1) year from the date of purchase by the
consumer. If at any time during the warranty period the product is
determined to be defective or malfunctions, Honeywell shall repair or
replace it (at Honeywell's option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to
the place from which you purchased it, or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer
Care will make the determination whether the product should be
returned to the following address: Honeywell Return Goods,
Dock 4 MN10-3860, 1885 Douglas Dr N, Golden Valley, MN
55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This
warranty shall not apply if it is shown by Honeywell that the defect or
malfunction was caused by damage which occurred while the prod-
uct was in the possession of a consumer.
Honeywell's sole responsibility shall be to repair or replace the prod-
uct within the terms stated above. HONEYWELL SHALL NOT BE
LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WAR-
RANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF
THIS PRODUCT. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so this limitation may not
apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEY-
WELL MAKES ON THIS PRODUCT. THE DURATION OF ANY
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF
THIS WARRANTY. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to
you.
This warranty gives you specific legal rights, and you may have other
rights which vary from state to state.
If you have any questions concerning this warranty, please write Hon-
eywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN
55422 or call 1-800-468-1502. In Canada, write Retail Products
ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive,
Scarborough, Ontario M1V4Z9.
If you have any questions about the operation of your thermostat,
please go to http://yourhome.honeywell.com, or call Honeywell
Customer Care toll-free at 1-800-468-1502.
sBacklight
6.
tTemperature Setting
7.
uTechnical Specifications
8.
;Warranty
9.
Customer Assistance
10.
400-114-014-B_69-2022-1 (Cadet TL7235) ENG.fm Page 2 Wednesday, October 17, 2007 8:58 AM