Hosen HS-LMS60R User manual

1
LED SPOT 60 MOVING HEAD
USER MANUAL
HS-LMS60R

2
1. BEFORE YOU BEGIN
What is included
LED SPOT 60 MOVING HEAD
SER MAN AL
POWER PL G
npacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to
ensure that all parts are present, and have been received in good condition. Notify the shipper
immediately and retain packing material for inspection if any parts appear damaged from
shipping or the carton itself shows sings of mishandling . Save the carton and all packing materials.
In the event that a fixture must be returned to the factory , it is important that the fixture be returned
in the original factory box and packing.
Safety Instructions
Please keep this ser Guide for future consultation. If you sell the unit to another user ,be sure
that they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage , and that the line voltage you
are connecting to is not higher than that stated on the decal or rear panel of the fixture .
This product is intended for indoor use only!
To prevent risk of fire or shock ,do not expose fixture to rain or moisture .Make sure there are
no flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation , at least 20in (50cm)
from adjacent surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing fuse and be sure to replace
with same fuse size and type.
Secure fixture to fastening device using a safety chain .Never carry the fixture solely by head.
se its carrying handles.
Maximum ambient temperature (Ta) is 104 ° F(40 ° C).Do not operate fixture at temperatures
higher than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair
the unit by yourself .Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center .Always use the same type spare
parts.
Don’t connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Avoid direct eye exposure to the light source while it is on.

3
1: SWlTCH ON/OFF
2: DMX IN
3: DMX O T
4: POWR IN
5: M NE/SC
6: P
7: DOWN
8: ENTER

4
2.INTROD CTION
Feature
CONTROL FEAT RES
13 CHENNELS DMX-512
PAN: 540 TILT: 255
7 COLOR + WHITE
7 GOBOS + WHITE
FOCUS
3-FACET PRISM
VARIABLE ELECTRONIC STROBE
VARIABLE ELECTRONIC DIMMER
VECTOR SPEED CHANNEL FOR TILT/PAN
BUILT IN MOVEMENT MACROS VIA MASTER/SLAVE OR DMX
SOUND ACTIVED
ADDITONAL FEAT RES
COMPACT & LIGHTWEIGHT
LED DISPLAY MEN WITH INVERT, RESET TO FACTORY
SETTING OPTION
PAN/TILT INVERT OPTION
FAN COOLED
DMX Channel Summary - 13 Channel mode
Channel
Function
CH1 P A N
CH2 T I L T
CH3 O P E N + S H T T E R
CH4 C O L O R W H E E L 7 C O L O R
CH5 G O B O W H E E L 7 G O B O
CH6 G O B O R O T A T I O N
CH7 S P E E D F O R
CH8 Dimming
CH9 P A N 1 6 B I T
CH1 0 T I L T 1 6 B I T
CH11 FOC S
CH12 3-Facet prism
CH13 prism Rotation

5
3.SET P
Fixture Linking
You will need a serial date link to run light shows of one or more fixtures using a DMX-512
controller or to run synchronized shows on two or more fixtures set to a master/slave operating
mode. The combined number of channels of channels required by all the fixtures on a serial data
link determines then number of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line . To comply with
the EIA-485 standard no more than 32 devices should be connected on one data
link. Connecting more than 32 fixtures on one serial data link without the use
of a DMX optically-isolated splitter may result in deterioration of digital
DMX signal.
Maximum recommended serial data link distance: 500 meters (1640ft)
Maximum recommended number of fixtures on a serial data link : 32 fixtures
DMX DATA CABLE
se a Belden 9841 or equivalent cable which meets the specification for EIA
RS-485applications.Standard microphone cables cannot transmit DMX data reliably over long
distances. The cable will have the following characteristics:
2-conduuctor twisted pair plus a shield .
Maximum capacitance between conductors - 30 pF/ft.
Maximum capacitance between conductor and shield - 55pF/ft.
Maximum resistance of 20 ohms /1000 ft.
Nominal impedance 100-140 ohms.

6
CABLE CONNECTORS
Cabling must have a male XLR connector on one and a female XLR connector on the other end .
DMX connector configuration
CA TION Do not allow contact between the common and the fixture’s chassis ground.
Grounding the common can cause a ground loop, and your fixture may perform erratically.
Test cables with an ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-OIN TO 5-PIN CONVERSION CHART
Notel If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin
to 3 pin adapter.
The chart below details a proper cable conversion:
3-OIN TO 5-PIN CONVERSION CHART
Conductor 3 Pin Female (output) 5Pin Male (Input)
Ground/Shield Pin1 Pin1
Tata (-) signal Pin2 Pin2
Tata (-) signal Pin3 Pin3
Do not use Do not use
Do not use
Setting up a DMX Serial Date Link
1. Connect the (male) 3 pin connector
side of the DMX cable to the output
(female)3 pin connector of the
controller.
2. 2. Connect the end of the cable coning
from the controller which will have a
(female) 3 pin connector to the input
connector of the next fixture
consisting of a (male) 3 pin connector.
3. Then ,proceed to connect from the
output as sated above to the input of the
following fixture and so on.

7
Master/Slave Fixture Linking
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first
fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the
input connector of the next fixture consisting of a (male) 3 pin connector. Then proceed to connect from the
output as stated above to the input of the following fixture and so on
Mounting
ORIENTATION
This fixture may be mounted in any position provided there is adequate room for ventilation.
4.OPERATING INSTR CTIONS
Navigating The Control panel
Access control panel functions using the four panel buttons located directly underneath the LCD Display.
When a menu function is selected. The display will show immediately the first available option for the
selected menu function, To select a menu item, press<ENTER>
Press the <MODE/ESC>button repeatedly until you reach the desired menu function. se the < P>and
<DOWN> buttons to navigate the menu options. Press the ，ENTER>button to select the menu function currently
displayed, or to enable a menu option. To return to the previous option or menu without changing the value. Press
the <MODE/ESC>button.
RIGGING
It is important never to obstruct the or vents pathway. Mount the
fixture using ,a suitable “c” or“o” type clamp. Adjust the angle of the
fixture by loosening both knobs and tilting the fixture. Finding the
desired position, retighten both knobs.
When selecting installation location, take into consideration lamp
replacement access and routine maintenance.
Safety cables must always be used.
Never mount in places where the fixture will be exposed to rain ,high
humidity ,extreme temperature changes or restricted ventilation..

8

9
5. DMX CHANNEL PROTOCOL
Channels DMX Control Content Description
CH1 000-255 PAN MOVEMENT
CH2 000-255 TILT MOVEMENT
CH3 000-255 PAN/TILT SPEED
000-017 WHITE
018-034 COLOR 1
035-051 COLOR 2
052-068 COLOR 3
069-085 COLOR 4
086-102 COLOR 5
103-108 COLOR 6
109-128 COLOR 7
129-192 WHOLE WHEEL FORWARD F-S
CH4 COLOR
193-255 WHEEL BACKWARD S-F
000-018 WHITE
019-037 GOBO 1
038-056 GOBO 2
057-075 GOBO 3
076-093 GOBO 4
094-113 GOBO 5
114-132 GOBO 6
133-144 GOBO 7
145-208 WHOLE WHEEL FORWARD F-S
CH5 GOBO
209-255 WHEEL BACKWARD S-F
000-011 NOT ROTATION
012-130 F-S
CH6
GOBO
ROTATION 131-255 S-F
000-011 WHITE
012-030 RESET AFTER 10 SECOND
031-250 SH TTER S-F WHITE
CH7
STROBOFLASH
251-255 WHITE
CH8 DIMMING 000-255 LINEAR DIMMING FROM LIGHT TO
DARK
CH9 000-255 X 16bit
CH10 000-255 Y 16bit
CH11 FOC S 000-255 LINEAR FOC S
CH12 PRISM: 000-255 OPEN
000-11 NOT ROTARION
012-130 FORWARD ROTATION FROM FAST TO
SLOW
CH13 PRISM
ROTATION
131-255 BACKWARD ROTATION FROM SLOW TO
FAST

10
5.APPENDIX
Technical Specification
WEIGHT&DIMENSIONS
Length............................................................................................330mm
Width..............................................................................................330mm
Height..............................................................................................480mm
Packing size............................................................. 520x430x420mm
Net weight..........................................................................................11 kgs
Gross weight ................................................................................ 13kgs
POWER
Powersettings.............................................................220V50Hz/60Hz
Fuse........................................................................................2A220V
Consumption...............................................................................150W
LIGHT SOURCE
1 X 60W WHITE............................
COLOR...........................................................
LAMP LIFE: 50,000Hrs
CONTROL & PROGRAMMING
Data output................................................locking3-pinXLRmalesocket
Datainput..............................................locking3-pinXLRfemalesocket
Protocols...............................................................................DMX-512
DMX channels..................................................................................13