Hosen HS-MB260 User manual

1
260W beam moving head light
HS-MB260
User Manual
Keep This Manual For Future Needs

2
Instruction
·Lamp: 260W Imported Lamp
·Channel mode: 18 DMX512 Channel
·Pan scan：540°(16bit) Electric correction
·Tilt scan：270°(16bit) Electric correction
·Amazing dot matrix ,four tact switch, 180°turning show
·one color wheel, 13 colors + and open Gobo: 11 pattern + blank
·Prisms:2 independent rotating prisms create 24 beam effect, two-way rotating prism plate, beam angle can be fre
ely scaled.
·0-100% mechanical dimming, mechanical dimming and free dimming available.
strobe macro control available.
·Lens optical system mechanical focus. beam angle 0～3.8°
·Over heat protection
·Voltage: 100-240V, 50/60Hz
·power: 375W
·IP Rate :IP20 Rate
·Dimensions:310x240x580mm
·Net weight：14.80KG
Before any installation, maintain and clean lamp, please make sure the power is off.
1.Operation
touch
wheel
function
Up
turn left
option/edit
down
turn right
option/edit
OK / Enter
press the wheel
Executive start / exit
return
when return menu ,press the wheel
return previous page
Set ”Modify address code” as an example, tell about the using of the touch.
1. Touch button “setting” in the main interface, and then into “setting” interface.
2. The 4 touch button in the right, are “up”, “ok”, “down”, “back”.
3. Press “up” or “down” button select “DMX address”.
4. Press “ok” button into editing state.
5. Press “up” button or “down” button modification address code (using the new address immediately and autosave)
6.Press “OK” button out of the editing state ( could omitted)
7. Press “back” button back to the main menu.
If using the wheel, process like bellow :
1. In the main interface , turn the wheel, select “setting” button.
2. Press the turn wheel and then loosen, into “setting” interface.
3.In the “setting” interface, select “DMX address”
4. Press the turn wheel and then loosen, into the editing state.
5. Turn the wheel, modification address code
6. After modification, press turn wheel and then loosen, out of the editing state.
7. Turn the wheel select “back”, press turn wheel and then loosen, back into the main interface.

3
2. Interface description
2.1 Main Interface
Top right corner 3 button for language switching and screen rotation.
EN: English
Bottom row four button corresponding sub interface is introduced, it’s in the back.
With touch operating mode sub interface is introduced, if use wheel, corresponding relation as follows:
Press up : turn left
Press down : turn right
Press ok : press the wheel
Use wheel operation dialog box
If ok, press the wheel. if cancel, turn the wheel.
2.2 Set up the interface
Option
Instruction
Run Mode
DMX
Slave state:Accept control table or main engine
Automatic
Statistics: Automatic operation and send DMX signal for slave
Note:If the bulb is putout before , the light bulb will not be full light. If you need to
observe the lighting effects, please keep the light on, and then into the automatic
state
DMX
Address
1-512
Press OK key into edit state, its selected hundred. Press up or down,change
address code.Press again OK key, selected ten editor. Press again OK key,
select the edit. Press it again to exit the edit state.
Channel
Mode
16CH
The 17th to 20th channels areinvalid.
20CH
Control Speed of th 17th to 20th channels
Invert
Pan/Tilt
OFF
NO
Swap
Pan-Tilt
OFF
NO
Change the channel of XY axis (include trimming)

4
Encoder
Pan-Tilt
NO
Use encoder correct position
OFF
Do not use encoder correct position
No DMX
Signal
KEEP
According to the original state continues to run
CLEAR
The return of the motor, stop running
Display
Power Save
NO
Free 30 seconds after closing backlight
OFF
Backlight ever bright
Burn on
start up
OFF
Power on directly after reset, no light bulb (need to use the menu or control table
to manual light bubble)
NO
After power on automatic light bubble, must wait for the light bulb light up
success can be reset
Load
Default
Press ok key see the confirmation dialog box, again press ok key, Press OK key
into edit
2.3. Information interface
Option
Instruction
Total using time
Cumulative using time (Accuracy to the minute)
The use of time
Use of time since the boot (Accuracy to the minute)
System error logs
If the red indicator shine ,that mean the lamps runs error . The details can be entered
sub-interface to view
After you finish view,
you can press the "OK" key to make the error log empty. Pay attention: Sometimes not
the Hall or optical coupler installation problems, But the motor cable is connected
backwards
2.4. Manual control interface
This interface use to control present light, neither belong to the from the machine state (didn’t received DMX signal),
nor belong to Host state( send DMX signal).
Option
Instruction
Reset
Press ok key see the confirmation dialog box, again press ok key, enter the reset interface, all
motor reset.
Color wheel
0-255
Press OK key into edit state, its selected hundred. Press up or down,change
channel value .Press again OK key, selected ten editor. Press again OK key,
select the edit. Press it again to exit the edit state.
……
0-255
the speed of
gobo wheel
0-255
Blub control
ON
OFF
2.5 Advanced interface
Password is “Up down up down “ . For the runner , password is “Left right left right”
Touch operation : Press one time on the “up” key (Appear the first “*” ),Then press one time on the “down” key
(Appear the second “*” ) , Press one time on the “up” key again (Appear the third “*” ) , Press one time on the “down”
key again (Appear the fourth “*” ) . At last press “OK” key to do the password authentication .
Runner operation : Turn to the left 1 bar (Appear the first “*” ), then turn to the right 1 bar (Appear the second “*” ),

5
Turn to the left 1 bar again (Appear the third “*” ), Turn
to the right 1 bar again (Appear the fourth “*” ) . At last press runner key to do the password authentication.
Option
Instruction
Touch screen adjustment
After entering the calibration interface, Follow the cross cursor tips
go touch the corresponding position. If the four locations to the
correct data is received. Then complete the calibration and save
the calibration data. If the calibration fails , This process will
continue the cycle ,then can at any time by pressing the "OK"
button to interrupt calibration.
Reset calibration (Zero calibration)
After entering the sub-interface, Can be adjusted x-axis, Y-axis to
the motor’s reset position. To compensate for hardware installation
error.
With address code and channel value different , reset calibration
not support One-digit Two-digit Three-digit edited respectively. Not
support long press too . And must be in 1 unit step-by-step
calibration .
Pay attention : Don’t reset calibration when the motor work. If
motor is working ,Please stop it then start to reset calibration.If
necessary, Please reset operation one time before reset
calibration .
2.6 DMX Channel List
Channel
Channel Mode
16
1
Color wheel
2
/Strobe
3
Dimmer
4
Gobo
5
Prism 1
6
Prism 1 rotating
7
Prism 2
8
Prism 2 rotating
9
Focus
10
X
11
X fine turning
12
Y
13
Y fine turning
14
XY speed
15
Frost
16
Colorful
17
Lamp Control
100－105 Turn off lamp
200－205 Turn on lamp
18
Reset
250－255 Reset

6
CHANNEL
DESCRIPTION
VALUE
EFFECT
CH1
COLOR WHEEL
0-8
8-15
16-23
24-31
32-39
40-47
48-55
56-63
64-71
72-79
80-87
88-95
96-103
104-111
112-127
128-191
192-255
White
Color 1
Color 2
Color 3
Color 4
Color 5
Color 6
Color 7
Color 8
Color 9
Color 10
Color 11
Color 12
Color 13
Color 14
Rainbow Forward Rotation Fast-Slow
Rainbow Reverse Rotation Slow-Fast
CH2
STROBE
0
1-50
51-240
241--255
Shut
Open
Strobe Slow-Fast
Open
CH3
DIMMER
0-255
Dark-Bright
Control signal wire connection
Use the CLR-XLR controller line connect every light’s DMX input port from controller’s DMX input port, and start from
the first light’s DMX input port connect to the second light’s DMX input port, in this way, until connect all of the lights,
and then use the loop accompanied connect to the last light's signal input port the connect complet, as the follow
picture:
Note:
Please remember that in the last table lamps and lanterns signal outlet connection a loop plug.In this loop inserted in
The CANON plug between 2 and 3 feet . Connect a 120 European resistance, connect this loop plug can avoid DM
X512 signal reflection phenomenon in the transmission process of signl.
This lamp use 3 core XLR plug (plug seat) . If use 3 core XLR plugs (plug seat), you must use a conversion line (5
core to 3 core), as shown: The conversion of three and five core plug (male and female)

7
Three core canon plug DMX512 interface circuit
Maintenance
a. If the light’s lens damaged or broken, and should need change the new lens, if the bulb damaged or have any
deformation, make the light dim, it says that the bulb had run out of its life., should change in time. There are 3
thermal protection device, using for cut off the lights power when it is heating. If the thermal protection device set up,
and then need to check whether the fan is normal.
b. It need Periodically to clean the light out and in optical lens and the reflector’s. put out for the optimization lighting
effect, clean time need to see the lights operating frequency and the using of the surrounding environment, using the
soft cloth or general glass cleaning products to clean. Suggest clean the external optical system every 20 day, at least
clean the internal optical system every 60 days.
c. Please don’t to use the alcohol etc organic solvent clean the out shell, in case it is damaged.
Statement
a . When the products manufactured, They are good performance, complete packaging . All users should comply with
the warnings and instructions stated above . Any damage caused by misuse is not within the scope of the company's
warranty . Operation manual of neglect caused problems and the fault is not in the dealer is responsible within the
scope of Neglect operation manual due to problem is out of dealer responsibility .
b. This handbook stated related matters explanation right belongs to our company .
This lamp use 3 core XLR plug((plug seat). If use 3 core XLR plugs (plug seat), you must use a conversion line (5
core to 3 core), as shown:The conversion of three and five core plug.