Hoshizaki HRE-MA series User manual

L1R262305 (042213)
HRE-MA series
HRE-MA 系列
HFE-MA series
HFE-MA 系列
INSTRUCTION MANUAL
使用说明书
COMMERCIAL REFRIGERATOR/FREEZER
商用冷藏柜 / 冷冻柜

ENGLISH
1
WARNING
Do not wet this product or use it in
potentially wet conditions. This may
cause electric leakage, resulting in
electric shock or re.
IMPORTANT
1. This booklet is an integral and essential
part of the product and should be kept and
preserved by the user. Please read carefully
the guidelines and warnings contained herein
as they are intended to provide the installer/
user with essential information for the proper
installation and the continued safe use and
maintenance of the product. Please preserve
this booklet for any further consultation that
may be necessary.
2. This is a commercial refrigerator/freezer,
and should be destined only to be used
for the purpose for which it has been
expressly designed. Any other use should
be considered improper and therefore
dangerous. The manufacturer will not be held
liable or responsible for any damage caused
by improper, incorrect and unreasonable
use.
3. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or l ack o f exper ience and kn owled ge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Young children should be supervised
to ensure that they do not play with the
appliance.
I. INSTALLATION INSTRUCTIONS
1. CONSTRUCTION (HRE-127MA-CHD)
Keep Dry
2. ACCESSORIES
Width 700mm 1200/1400mm 1800mm
a) Shelf: 4 [4] 8 [8] 12 [12]
b) Shelf clip: 12 [16] 24 [32] 36 [48]
c) Shelf holder: 4 [0] 8 [0] 12 [0]
Note: 1. Numbers in parentheses are for models
without shelf holders.
2. Customized products may have different
numbers of accessories.
3. LOCATION
IMPORTANT
This refrigerator/freezer is not intended for
outdoor use. Normal operating ambient
temperature should be within 5°C to 43°C.
For best operating results:
* The refrigerator/freezer should not be located
next to ovens, grills or other high heat producing
equipment.
* The location should provide a rm foundation for
the equipment.
Min.30cm
Min.100cm
Fig. 1
Front Panel
Refrigeration Unit
Door
Leg
Shelf
Machine
Compartment

ENGLISH
2
4. SET UP
IMPORTANT
1. Do not tilt the unit more than 45° when
mounting the legs.
2. Carry the unit by holding its bottom.
1) Cut the vinyl shipping tape and remove the
carton.
2) Take out the accessory shelves, shelf clips and
legs. Attach the four shelf clips horizontally to the
shelf posts. Place the shelf on the shelf clips.
3) Remove the two bolts from the bottom of the
unit.
Min.30cm
Min.100cm
Fig. 2
Min. 30cm
Min. 100cm
4) Turn the unit 90 degrees on the pallet, tilt the unit
sideways, and screw in the two adjustable legs.
Note: Keep the adjusters 2 cm longer to make it
easy to pull out the pallet.
* Avoid a site where dripping is not allowed.
Especially, a side-by-side or back-to-back
installation (possibly with other manufacturer’s unit)
may cause condensation between the two units,
resulting in dripping onto the oor.
* Do not expose the unit to direct sunlight or higher
temperatures.
* Allow at least 100 cm clearance at the front of the
unit for smooth door operation. Also allow at least
30 cm clearance from the ceiling to the top of the
unit for proper air circulation.
Fig. 5
Adjustable Leg
Adjuster
Leg Height Longer Shorter
Fig. 3
M20 Bolt
Fig. 4
5) Tilt the unit in the opposite direction, and screw
in the other two legs.
6) Slide out the pallet from under the unit.
7) For the 180 type (1800 mm wide) models only,
turn the unit sideways again, and screw in the
two legs at the center.
8) Level the refrigerator/freezer in both the left-to-
right and the front-to-rear directions. To adjust
the height of the unit, turn the adjusters of the
adjustable legs.
CAUTION
The height of the adjustable legs must be within
9 - 12 cm (or 15 - 18 cm for some models).
If extended too much, the legs may become
weak or the adjusters can come off, causing
unexpected injuries.

ENGLISH
3
Fig. 6
Shelf Clip
Shelf Post
Push
Hook
9) Remove the protective plastic lm from the doors
and front panel.
5. SHELF AND SHELF CLIP
* The shelf is adjustable in 2.5 cm increments. Adjust
the shelf clips according to the height of stored
items.
* To attach the shelf clip, insert the upper tab into
an adjust hole in the shelf post to hook the shelf
clip, and push the lower tab into another adjust
hole until it locks in place. To detach the shelf clip,
reverse the above procedure.
CAUTION
Attach the shelf clips properly to make the
shelf level.
* To lay the shelf at the bottom of the cabinet, attach
two shelf holders each to the left and right frames
as shown below.
6. ELECTRICAL CONNECTIONS
IMPORTANT
This refrigerator/freezer is provided with no
power switch or earth leakage circuit breaker,
but with overcurrent protection only. Install an
earth leakage circuit breaker with overload
protection rated at least 15A on the main
power supply.
* This refrigerator/freezer must be plugged into
the separated power receptacle which is readily
accessible and has enough capacity. The
maximum allowable voltage variation should not
exceed ± 10 percent of the nameplate rating. See
the nameplate.
* If the supply cord and the plug should need to be
replaced, it should only be done by a qualified
service engineer to avoid any danger.
7. DRAIN CONNECTIONS
CAUTION
Be sure to connect the drain hose properly.
Otherwise water leaks from the drain hose may
damage the surroundings (property).
IMPORTANT
1. Drain line shall be as short and straight
as possible. The drain hose shall have an
adequate pitch and fall so that no part is
higher than the drain outlet.
2. To prevent a backflow, do not connect the
drain hose directly with the sewer system.
An air gap of a minimum of 5 cm should be
between the end of the drain hose and the
water level of drainage.
IMPORTANT
Do not put anything at the bottom of the
cabinet to prevent damage or deformation to
the cabinet bottom, resulting in corrosion.
5 cm or more
Water Level
3. When installing more than two units, do
not interconnect their drain hoses. If the
interconnection is necessary, provide an air
inlet per unit.
5 cm or more
Air Inlet Water Level
Fig. 7

ENGLISH
4
7. Do not use combustible spray or place
volatile and ammable substances near the
unit. They could catch re from a spark of a
switch or the like.
8. D o not p ut a nyt hi ng i nt o t he m ac hi ne
compartment or the air inlet/outlet. The fan
rotating rapidly inside may cause injury or
heat.
9. Energise the refrigerator/freezer for 1 hour
and check for proper temperature before
putting foods in the cabinet.
10. Do not block the air inlet/outlet with foods.
11. Do not pack the cabinet with foods. Allow
some space between them to ensure good
air ow.
12. Do not put in warm or hot foods. Let them
cool first, or they will raise the cabinet
temperature and could deteriorate other
f o o d s i n t h e c a b i n e t o r o v e r l o a d t h e
refrigerator/freezer.
13. Make sure all items are snug on each shelf.
14. Moist or fresh foods and those with a strong
smell like seafood should be wrapped up
in a plastic film or packed in a container.
Otherwise the foods may dry up or give their
smells to other foods.
15. Foods containing acetic acid or yeast should
be wrapped up in a plastic film. Otherwise
they may accelerate corrosion of the
evaporator and copper tubes, resulting in
failure.
16. Foods intended for direct human
consumption should be stored on the shelf in
a proper container and protected from direct
contact with the cabinet walls.
17. Do not use the freezer to freeze foods. It is
designed only to store frozen foods. High
quality ice cream may melt during defrost
cycle and should not be stored in the freezer.
18. The doors may become difficult to open
just after closed because of the negative
pressure created inside the cabinet. Wait for
about 30 seconds.
* The drain outlet is at the bottom of the body. Use
the accessory to connect the drain hose.
1) Insert the 18 mm diameter end of exible hose
into the defrost water drain outlet, and fix the
flexible hose with the accessory drain hose
band.
2) Attach the other end (26 mm outer diameter) of
the exible hose to the drainage.
Flexible Hose
(end: 26 mm outer diameter)
Defrost Water Drain Outlet
(18 mm diameter)
Fig. 8
* The drain hose may not be provided for some
models. If necessary, connect the optional drain
hose assembly (471190A02) to the 18 mm outer
diameter drain outlet located on the bottom rear of
the unit.
II. OPERATING INSTRUCTIONS
IMPORTANT
1. B e c a r e f u l n o t t o w e t t h e m a c h i n e
compartment. This might cause failure or
electric shock hazard.
2. To prevent electric shock, do not touch the
attachment plug with wet hands.
3. Do not store any volatile or flammable
substances, such as benzine, ether,
adhesives and LPG, in the unit.
4. This refrigerator/freezer is designed only
for temporary storage of foods. Use for any
other purposes (e.g. storage of chemicals
or medical supplies such as vaccine and
serum) could cause deterioration of stored
items.
5. Do not throw anything onto the shelves or
load more than 60 kg on each of them. They
may fall off and cause injury.
6. Do not store bottles or cans near the air
outlet. They may freeze up and break,
causing a risk of injury.

ENGLISH
5
To remove the front panel:
Release both sides of the bottom from the grips, and
lift it off vertically.
Fig. 9
Front Panel
Grip
3. CABINET TEMPERATURE SETTING
IMPORTANT
1. Pressing the down key will not speed
up refrigeration, but will only lower the
temperature setting.
Fig. 10
Front Panel
Grip
1. START UP
1) Plug in the unit.
2) The compressor and condenser fan motor will
start in 3 minutes.
2. FRONT PANEL
To open and close the front panel:
Pull each side of the front panel toward you to
release it from the grip on each side of the bottom,
and swing up the front panel as shown.
To close the front panel, t both sides of the bottom
securely in the grips.
2. The temperature range given below is only
the adjustable range. The actual cabinet
temperature depends on the ambient
temperature and other conditions.
The cabinet temperature is factory-adjusted to
1°C for the refrigerator and -20°C for the freezer. If
necessary, readjust the temperature as follows.
Refrigerator
[8]
[7]
[6]
[2]
[3]
[4]
[1]
[5] Operation Panel
Fig. 11
[1] Defrost Indicator Light
[2] Refrigeration Indicator Light
[3] Set Key
[4] Defrost/Reset Key
[5] Set Indicator Light
[6] Screen
[7] Down Key
[8] Up Key
1) Open the front panel.
2) Press the set key for 3 seconds:
When the keypad password is set as “0”, the
set indicator light comes on and the screen
displays the “F01” menu. There is no password
authentication, so directly enter the menu mode to
set parameter.
When the keypad password is not set as “0”,
the set indicator light flashes and the screen
displays “00”. Press the up or down key to input
the password “55”. Press the set key to conrm
the password input. Then, the system enters the
menu setting item if the password is correct. If
the password is incorrect, the set indicator light
goes off and the system goes back to the normal
measuring and controlling status.
3) Temperature setting:
Press the up key. The set indicator light flashes
and the screen displays the set temperature.
Press the down key. The set indicator light ashes
and the screen displays the temperature of the
evaporator sensor.

ENGLISH
6
After entering the menu setting items, press the
up or down key to choose the “F02” menu (see
note 2).
After choosing the “F02” menu, press the set key
to set parameter value. Press the up or down key
to adjust parameter value, and then repress the
set key to go back to the menu choosing status.
Under the setting status, press the defrost/reset
key or perform no operation for 30 seconds. The
system will save the parameters and exit from the
parameter setting mode.
Code Function Set Range Default Unit
F01 Menu password 00 to 99 55 NC
F02 Temperature setting -2 to +12 1 °C
IMPORTANT
1. The temperature setting must be between -2
and 12°C to prevent possible failure.
2. To avoid the risk of failure, do not make
changes to other menus than “F02”.
3. The displayed cabinet temperature
is a d ju st ed to be a l mo st e q ua l to t h e
temperature at the center of the cabinet
without foods. But it can be different from
the actual temperature depending on
arrangement of stored foods, frequency of
door opening or measuring points.
Freezer
Fig. 12
[1] Fan Indicator Light
[2] Set Indicator Light
[3] Refrigeration Indicator Light
[4] Defrost Indicator Light
[5] Defrost/Down Key
[6] Set/Up Key
1) Open the front panel.
Operation Panel
[3] [2] [1]
[4]
[6]
[5]
2) Press the set key for 3 seconds:
When the screen displays “SEt”, press the set key
again to indicate the set temperature. Press the
up or down key to set the desired temperature
and press the set key. When the screen displays
“SEt”, press the set key again for 3 seconds or
perform no operation for 10 seconds. The system
will save the set temperature and indicate the
cabinet temperature on the screen.
IMPORTANT
1. The temperature setting must be between -7
and -23°C to prevent possible failure.
2. To avoid the risk of failure, do not make
changes to other menus than “SEt”.
3. The displayed cabinet temperature
is adjusted to be almost equal to the
temperature at the center of the cabinet
without foods. But it can be different from
the actual temperature depending on
arrangement of stored foods, frequency of
door opening or measuring points.
Refrigerator / Freezer (Common)
The compressor stops when the cabinet temperature
reaches down to the set temperature, and starts
when the cabinet temperature rises to the set
temperature + 4°C. Accordingly, the average cabinet
temperature will be around the set temperature +
2°C.
Set temperature (compressor off temperature)
Off-cycle defrost (HRE series): -2 to +12°C
Heater defrost (HFE series): -7 to -23°C
Fig. 13
Average Cabinet
Temperature
Set Temperature
Compressor
ON
OFF
Time
4K
Interior Thermistor Temperature

ENGLISH
7
4. DEFROST
Automatic defrost cycle
The refrigerator/freezer automatically defrosts the
evaporator 3 hours (refrigerator) or 6 hours (freezer)
after the refrigeration starts. The defrost indicator
light on the operation panel comes on when the
defrost cycle starts.
Manual defrost cycle
To start the manual defrost cycle, press the defrost/
rest key (refrigerator) or defrost key (freezer) for 3
seconds. The defrost indicator light on the operation
panel comes on when the defrost cycle starts.
5. INDICATOR LIGHTS
Refrigerator
Indicator Light Symbol Status Function
Set SET On Parameter setting
Off Measuring and controlling
status
Flash Parameter check,
password input
Refrigeration On Refrigerating
Off Refrigeration stopped
Flash Refrigeration delayed
Defrost On Defrosting
Off Defrost stopped
Freezer
Indicator Light Symbol Status Function
Refrigeration On Compressor running
Off Compressor stopped
Flash Compressor delayed
Quick
ash
Manual refrigeration
Defrost On Defrosting
Off Defrost stopped
Flash Defrost drain
Quick
ash
Manual defrost
Fan On Fan running
Off Fan stopped
Flash Fan delayed
Set SET On Setting mode
Off Normal mode
Celsius C On Celsius display under
normal mode
Off Fahrenheit display under
normal mode
6. SHUT DOWN
1) Before shutting down the unit, move the stored
foods into another refrigerator/freezer.
2) Unplug the unit or disconnect the main power
supply.
3) When preparing the unit for long storage, clean
the cabinet interior and door gaskets, dry them
thoroughly and store the unit in a dry place.
III. MAINTENANCE
IMPORTANT
1. B e f o r e c a r r y i n g o u t a n y c l e a n i n g o r
maintenance operations, unplug the unit.
2. Do not touch or wet the machine
compartment parts. This could result in
failure or breakdown.
3. To prevent possible damage, do not clean
the plastic parts with water above 40°C or in
a dishwasher.
1. INTERIOR, EXTERIOR, SHELF
* Clean the interior and exterior at least once a week
for sanitary use.
* Clean off the interior and exterior with a soft cloth
soaked in cold or warm water containing the proper
amount of neutral cleaner and wrung dry. Do not
use a water jet to clean the machine compartment.
* Chemical agents other than neutral cleaner might
cause damage to the interior and exterior surfaces.
* Any remaining detergent will damage metal or
plastic surfaces. Use a soft cloth dampened with
warm water to wipe it off.
* Do not use the following items. They could damage
painted or plastic surfaces:
Polishing powder, alcohol, thinner, benzine, acidic
or alkaline detergent, hot water, petroleum, soap
powder, metal scourer or brush, etc.
Especially detergent to clean grease on ventilator
or microwave.

ENGLISH
8
Fig. 15
Air Filter Front Panel
2) Wash the air filter carefully with cold or warm
water containing the proper amount of neutral
cleaner. Rinse and dry the air lter thoroughly.
3) To ret the air lter, attach it to the guide at the top
of the condenser and put the tabs into the slots in
the refrigeration unit base.
Guide
Base
Slot
Fig. 16
Air Filter
3. BEFORE CALLING A SERVICE AGENT
IMPORTANT
1. If the screen on the operation panel indicates
an error code or something seems wrong
with the unit, check for possible causes
according to the following instructions. If the
problem still exists, immediately contact an
authorized Hoshizaki service company.
2. When contacting a service company, let
them know the model name, serial number,
date of installation (see warranty card) and
state of the trouble.
3. Do not attempt to repair the unit yourself.
[a] TROUBLES WITH ERROR CODE INDICATION
Refrigerator
Code Possible
Cause Operation and Remedy
E1 Cabinet
sensor
error
Compressor shuts down. Press any key
to stop beep. When troubleshooting is
over, system recalculates compressor
delay time. Immediately contact an
authorized Hoshizaki service company.
E2 Evaporator
error
Defrost termination temperature is
invalid. Press any key to stop beep.
Immediately contact an authorized
Hoshizaki service company.
Note: Some solutions other than the above may
also damage painted or plastic surfaces.
Immediately stop using such solutions if
they cause any problems.
* The door gasket and its contact surface get
soiled easily. Clean every surface of these parts
thoroughly. Remnants of food will accelerate aging.
* Use a cloth to wipe off any water staying inside the
cabinet.
2. AIR FILTER
IMPORTANT
To prevent deformation, do not wash the air
lter with hot water above 40°C.
Plastic mesh air lters remove dirt or dust from the
air, and keep the condenser from getting clogged.
If the filters get clogged, the refrigerator/freezer’s
performance will be reduced. Check the filters at
least twice a month. When clogged, use warm water
and a neutral cleaner to wash the filters. Do not
operate the unit with the air lters removed, or the
condenser will get clogged, resulting in failure.
1) Open the front panel and remove the air lter. To
prevent injury, do not touch the condenser fins
directly.
Fig. 14

ENGLISH
9
Freezer
Code Possible
Cause Operation and Remedy
HHH Ambient
temp too
high
Compressor cycles on for 45 minutes
and off for 15 minutes. Check ambient
temperature. If problem cannot be
resolved, immediately contact an
authorized Hoshizaki service company.
LLL Ambient
temp too
low
* The code “dF” is not an error code but indicates
the unit is in defrost cycle.
[b] TROUBLES WITHOUT ERROR CODE
INDICATION
1) Unit fails to operate:
(1) Unplugged.
(2) Power failure.
(3) Main power supply disconnected.
2) Poor cooling performance:
(1) Ambient temperature too high (above 43°C).
(2) Door(s) opened too often.
(3) Cabinet temperature setting too high.
(4) Too packed with foods.
(5) Air lter not clean.
(6) Door(s) left open.
3) Condensation around door(s):
(1) Ambient humidity too high.
(2) Door(s) not closed tightly.
4) Noise:
(1) Normal operating sounds of compressor or
condenser fan.
5) Frosting inside compartment:
(1) Ambient humidity too high.
(2) Door(s) opened too often.
(3) Too packed with foods beyond load line.
4. DISPOSAL
When disposing of the refrigerator/freezer, contact
an authorized Hoshizaki service company or a
specialized waste disposal company.
IMPORTANT
The insulation foaming agent used
for the unit body contains ammable
gas cyclopentane. With this in mind,
dispose of the refrigerator/freezer
properly.
5. WARRANTY
Hoshizaki warrants to the original owner/user that all
Hoshizaki branded products shall be free of defects
in material and/or workmanship for the duration of
the “warranty period”. The warranty shall be effective
for one year from the date of installation.
Hoshizaki’s liability under the terms of the warranty
are limited and shall exclude routine servicing,
cleaning, essential maintenance and/or repairs
occasioned by misuse and installations not in
accordance with Hoshizaki guidelines.
Warranty repairs should be completed by an
approved Hoshizaki dealer or service agency using
genuine Hoshizaki components.
To obtain full details of your warranty and approved
service agency, please contact your dealer/supplier,
or the nearest Hoshizaki Service ofce:
Hoshizaki Singapore
TEL: [phone]
FAX: [phone]
Hoshizaki Lancer
TEL: [phone]
FAX: [phone]
Hoshizaki Suzhou
TEL: [phone]
FAX: [phone]
Hoshizaki Shanghai
TEL: [phone]
FAX: [phone]
Hoshizaki Hong Kong
TEL: [phone]
FAX: [phone]
Hoshizaki Taiwan
TEL: [phone]
FAX: [phone]

中文
10
警告
请勿弄湿本产品或在潮湿环境下使用
本产品。否则可能会导致漏电，进而
造成触电或火灾。
重要
1. 使用说明书是本产品不可分割的重要组成部
分，用户须妥善保管。请务必仔细阅读本说
明书中描述的指南和警告事项，因为这些指
南和警告事项为安装人员 / 用户提供了正确安
装、持续安全地使用和保养本产品所需的重
要信息。请妥善保管本说明书，以便必要时
参考使用。
2. 本冷藏柜/冷冻柜为商用设备，仅适用于该设
备所指定的设计用途。用于任何其它用途将
被认为使用不当，并且将非常危险。对因本
产品使用不当、使用不正确和不合理而引发
的任何后果，生产厂家恕不承担责任。
3. 本产品不适合残障、智障及缺乏相应经验和
知识的人士(包括儿童)单独使用，除非有专人
负责其安全，并对其使用本产品加以监督和
指导。另外还应对年幼儿童加以看管，以确
保其不玩耍本产品。
I. 安装说明
1. 各部分名称 (HRE-127MA-CHD)
图1
前板
制冷机组
柜门
保持干燥
支脚
层板
2. 附件
宽度 700mm 1200/1400mm 1800mm
a) 层板： 4 [4] 8 [8] 12 [12]
b) 层板托： 12 [16] 24 [32] 36 [48]
c) 层板支架： 4 [0] 8 [0] 12 [0]
注：1. 中括号中的数值适用于无层板支架的机型。
2. 定制产品的附件可能会与上述不同。
3. 位置
重要
本冷藏柜/冷冻柜仅供室内使用。正常的工作环
境温度应介于5℃至43℃之间。
为达到最佳性能:
* 请勿将冷藏柜/冷冻柜摆放在炉子、烤架或其它会产
生高温的设备附近。
* 摆放位置应坚实，足以承受设备重量。
* 应避免将本机安装在出现滴水的场所。采用并排或
背靠背安装方式(可能是与其它厂商的产品一起安
机械室

中文
11
4. 安装方法
重要
1. 安装支脚时，请勿将本机倾斜超过 45°。
2. 搬动本机时，请托住其底部。
1) 剪断运输胶带，拆下纸板箱。
2) 取出附属的层板、层板托和支脚。将 4 个层板托
水平安装到层板立柱上，并将层板放置在层板托
上。
3) 从本机的底部拆下 2 个螺栓。
图2
最小30cm
最小100cm
4) 将本机在托架上转动 90°，使本机侧向倾斜，然
后安装两个可调节支脚。
注 : 应使调节器的高度超出托架 2cm，以便于
拉出托架。
装)时，由于两台机器之间可能会出现冷凝，从而导
致冷凝水滴落到地板上。
* 请勿将本机暴露在直射阳光或高温下。
* 在本机的前部至少留出100cm的空间,以确保顺利地
开关门。在本机顶部和天花板间应至少留出30cm的
空间，以确保空气流通顺畅。
图5
可调节支脚
调节器
支脚高度 调高 调低
图3
M20 螺栓
图4
5) 使本机朝反方向倾斜，并安装另外两个支脚。
6) 将托架从本机底部滑出。
7) 再次将本机侧向倾斜，然后安装中间位置处的两
个支脚。该操作仅限 180 型 (1800mm宽)机器。
8) 将本冷藏柜 / 冷冻柜在左右和前后方向上调水平。
若要调节本机高度，请转动可调节支脚的调节器。
注意
可调节支脚的高度必须在9～12(某些机型为15～
18)cm的范围内。如果伸出过长，可能会减弱支
脚强度，或者导致调节器脱落，造成意外受伤。

中文
12
图6
层板托
层板立柱
推压
挂钩
9)撕掉柜门和前面板上的塑料防护膜。
5. 层板和层板托
* 层板高度可以“2.5”高度单位进行调节。请根据存
放物品的高度调节层板托。
* 若要安装层板托，请将上部凸片插入层板立柱中的
调节孔以钩住层板托，然后将下部凸片推入另一个
调节孔，直至其锁止到位。若要拆下层板托，请按
照与上述相反的步骤操作。
注意
请正确安装层板托，以保持层板水平。
* 如下图所示，若要将层板放于柜体的底部，请在左
右边框处分别安装两个层板支架。
6. 电气连接
重要
本冷藏柜/冷冻柜未配备电源开关或接地漏电断
路器，而只配备过电流保护装置。请在主电源
上安装一个额定电流不小于15A的接地漏电断
路器。
* 本冷藏柜/冷冻柜的电源插头必须插入单独的电源插
座，且该插座必须方便插拔并具有足够的容量。允
许的最大电压波动不得超过铭牌上规定的额定电压
的±10％。详情请参见铭牌。
* 如需更换电源线和插头，请务必交由具备相应知识
的维修工程师进行更换，以免发生危险。
7. 排水管连接
小心
请务必切实连接好排水软管。否则，排水软管可
能漏水，进而破坏周围环境。
重要
1. 排水管路应尽量短而直，且应保证有足够的坡
度及落差，以确保管路高度始终低于排水口。
2. 为防止废水回流，请勿将排水软管直接连至
下水道系统。请在排水软管的末端与排水水
位间至少留出5cm的空隙。
重要
请勿在柜体底部放置任何物品，以防止柜体底
部受损或变形，从而导致腐蚀。
3. 当安装2台以上的机器时，请勿将排水软管连
在一起。如果需要连接在一起，请在每台机
器间留出足够的空隙。
* 排水口位于柜体的底部。请使用附件连接排水软管。
1) 请将挠性软管一端(直径18mm)插入除霜排水口
中，再用附带的排水软管卡箍固定挠性软管。
2) 将挠性软管的另一端(外径26 mm)连接到下水道系
统处。
5cm 以上
排水水位
5cm以上
进风口 排水水位

中文
13
* 某些机型可能不提供排水软管。 如有需要，请将选
购的排水软管总成(471190A02)连接到位于本机后
下方外径为18mm的排水口处。
II. 操作说明
重要
1. 请不要弄湿机械室。否则会导致本机故障或
触电。
2. 为防止触电，请勿用湿手触摸连接插头。
3. 请勿在本机中存放易挥发或易燃物品，如汽
油、乙醚、粘合剂和LPG。
4. 本冷藏柜/冷冻柜的设计用途是临时存放食
物。将其用于任何其它用途(例如存放疫苗、
血清等化学或医学用品)可能会导致存放的物
品变质。
5. 请勿将物品抛掷到层板上或者在单块层板上
放置60kg以上的物品。否则层板可能会掉落
并导致受伤。
6. 请勿在出风口处存放玻璃瓶或易拉罐。否
则，瓶罐中的液体可能会结冰和破裂，进而
导致受伤。
7.
请勿在本机附近使用可燃喷雾剂或放置易挥发
物品和易燃物品。否则，操作开关或类似装置
时产生的火花可能会导致这些物品起火。
8. 请勿在机械室内或进风口/出风口处放置任何
物品。内部高速旋转的风扇可能会造成人员
受伤或产生高温。
9. 在柜内放置食物前，请使冷藏柜/冷冻柜通电1
小时，并检查温度是否正常。
10. 请勿将食物放置在阻挡进风口/出风口的位置。
11. 请勿在柜内塞满食物。请在食物与食物之间
留出适当空间，以确保空气流通顺畅。
图9
前板
夹持器
12. 请勿放入温热或滚烫的食物。请首先让食物
自然冷却，否则会导致柜内温度上升，从而
可能会造成柜内存放的其它食物变质或导致
冷藏柜/冷冻柜过载。
13. 确保所有物品在各个层板上摆放有序。
14. 潮湿或新鲜的食物以及海鲜等具有强烈气味
的食物应使用保鲜膜包裹或存放在容器中。
否则，这些食物可能会变干或使得其它食物
串味。
15. 含有醋酸或酵母的食物应使用保鲜膜包裹。
否则，这些食物可能会加速蒸发器和铜管的
腐蚀，进而导致故障。
16. 直接食用的食物应放置在合适的容器内，并
且避免与柜壁直接接触。
17. 请勿使用冷冻柜来冷冻食物。冷冻柜仅用来
存放冷冻好的食物。除霜过程中，高品质冰
激凌可能会融化，因此不应将其存放在冷冻
柜中。
18. 柜门刚关闭时难以立即打开，因为此时柜内
会产生负压。请等待约30秒。
1. 启动
1) 插入本机的电源插头。
2) 压缩机和冷凝器风扇马达将在3分钟后启动。
2. 前板
打开和关闭前板 :
朝前方拉前板，以便将其从底部的夹持器上松开，然
后如图所示将前板向上翻。
要关闭前板，请将底部两侧切实卡入夹持器中。
挠性软管(端口：外径26mm)
除霜排水口(直径18mm)
图8

中文
14
1) 打开前板。
2) 按住设定按钮 3 秒钟 :
当密码设为“0”时，设定指示灯将点亮，且显示
屏上显示“F01”菜单。此时无密码验证，可直接
进入菜单模式以设定参数。
当密码未设为“0”时，设定指示灯将闪烁，且显
示屏上显示“00”。按向上或向下按钮，输入密码
“55”。按设定按钮，确认密码输入。如果密码正确，
则系统进入菜单设定。如果密码不正确，则设定指
示灯熄灭，系统回到正常测量和控制状态。
3) 温度设定 :
按向上按钮。设定指示灯将闪烁，且显示屏将显示
设定温度。
按向下按钮。设定指示灯将闪烁，且显示屏将显示
蒸发器的温度。
进入菜单设定后，按向上或向下按钮，选择“F02”
菜单 ( 参见注 2)。
选择“F02”菜单后，按设定按钮设定参数值。按
向上或向下按钮调整参数值，然后再次按设定按钮，
回到菜单选择状态。
在设定状态下，按除霜 / 复位按钮或在 30 秒钟内
不执行任何操作。系统将保存参数，并从参数设定
模式退出。
代码 功能 设定范围 默认值 单位
F01 菜单密码 00～99 55 NC
F02 温度设定 -2～+12 1 ℃
重要
1. 必须将温度设定在 -2 ～ 12℃的范围内，以
防止发生故障。
2. 为避免发生故障，请勿更改除“F02”以外的
其它菜单。
3. 显示的柜内温度被调节为与未放置食物时柜
内中心处的温度几乎相同。但根据存放的食
物、柜门开启频率或测量点不同，显示温度
可能会与实际温度有所不同。
冷冻柜
图11
[1] 除霜指示灯
[2] 制冷指示灯
[3] 设定按钮
[4] 除霜 / 复位按钮
[5] 设定指示灯
[6] 显示屏
[7] 向下按钮
[8] 向上按钮
拆下前板 :
将底部两侧从夹持器上松开，然后将其垂直提起。
3. 柜内温度设定
重要
1. 按向下按钮只能降低温度设定值，并不会起到
加快制冷速度的作用。
2. 下文中的温度范围仅指可调节范围。柜内的实
际温度取决于环境温度和其它条件。
柜内温度在出厂时设为1℃(对于冷藏柜)和-20℃(对于
冷冻柜)。如有需要，请按照如下方法重新调节温度。
冷藏柜
操作面板
[3] [2] [1]
[4]
[6]
[5]
[8]
[7]
[6]
[2]
[3]
[4]
[1]
[5] 操作面板
图10
前板
夹持器

中文
15
[1] 风扇指示灯
[2] 设定指示灯
[3] 制冷指示灯
[4] 除霜指示灯
[5] 除霜 / 向下按钮
[6] 设定 / 向上按钮
1) 打开前板。
2) 按住设定按钮 3 秒钟 :
当显示屏显示“SEt”时，再次按设定按钮以显示
设定温度。按向上或向下按钮设定所需的温度，然
后按设定按钮。当显示屏显示“SEt”时，再次按
住设定按钮 3 秒钟或者在 10 秒钟内不执行任何操
作。系统将保存设定温度，且显示屏上将显示柜内
温度。
重要
1. 必须将温度设定在 -7 ～ -23℃的范围内，以
防止发生故障。
2. 为避免发生故障，请勿更改除“SEt”以外的
其它菜单。
3. 显示的柜内温度被调节为与未放置食物时柜
内中心处的温度几乎相同。但根据存放的食
物、柜门开启频率或测量点不同，这一温度
可能会与实际温度有所不同。
冷藏柜 / 冷冻柜 ( 通用说明 )
当柜内温度下降至设定温度时，压缩机将停止运行。
而当柜内温度上升至高于设定温度 4℃时，压缩机将
启动。因此，柜内的平均温度将保持在高于设定温度
2℃左右。
设定温度 ( 压缩机关闭温度 )
停止运转除霜 (HRE 系列 ): -2 ～ +12℃
加热器除霜 (HFE 系列 ): -7 ～ -23℃
4. 除霜方式
自动除霜过程
在制冷过程启动后，冷藏柜 / 冷冻柜将自动对蒸
发器除霜 3 小时 ( 对于冷藏柜)或6小时(对于
冷冻柜 )。除霜过程启动时，操作面板上的除霜
指示灯将点亮。
手动除霜过程
若要启动手动除霜过程，请按住除霜 / 复位按钮
( 对于冷藏柜 ) 或除霜按钮 ( 对于冷冻柜 )3 秒钟。
除霜过程启动时，操作面板上的除霜指示灯将点
亮。
5. 指示灯
冷藏柜
指示灯 符号 状态 功能
设定 SET 点亮 参数设定
熄灭 测量和控制状态
闪烁 参数检查、密码输入
制冷 点亮 制冷
熄灭 停止制冷
闪烁 延迟制冷
除霜 点亮 除霜
熄灭 停止除霜
冷冻柜
指示灯 符号 状态 功能
制冷 点亮 压缩机运行
熄灭 停止压缩机
闪烁 延迟压缩机的运行
快速
闪烁
手动制冷
除霜 点亮 除霜
熄灭 停止除霜
闪烁 除霜排水
快速
闪烁
手动除霜
风扇 点亮 风扇运行
熄灭 风扇停止
闪烁 延迟风扇的运行
设定 SET 点亮 设定模式
熄灭 普通模式
摄氏度 C 点亮 普通模式下的显示摄氏度
熄灭 普通模式下的显示华氏度
图13
柜内平均温度
设定温度
压缩机 ON
OFF
时间
4K
内部热敏电阻温度
图12

中文
16
注： 上述以外的洗剂也有可能会损伤涂装保护面及塑
料表面。
出现异常时请立即停止使用。
* 柜门衬垫及其接触表面很容易变脏，请彻底清洁这
些部位。否则，食物残渣会加速这些部位的老化。
* 用抹布擦去柜内的积水。
2. 空气过滤网
重要
为防止空气过滤网变形，请勿使用 40℃以上的
热水清洗空气过滤网。
该空气过滤网可以滤除空气中的脏物或灰尘，以防止
冷凝器堵塞。 如果过滤网堵塞，冷藏柜 / 冷冻柜的制
冷性能将下降。每月应至少检查过滤网两次。如果过
滤网堵塞，请使用温水和中性清洁剂进行清洗。请勿
在空气过滤网已拆下的情况下使用本机，否则会导致
冷凝器堵塞，进而造成本机故障。
1) 打开前板并拆下空气过滤网。请勿直接触摸冷凝器
的翅片，以免受伤。
6. 关机
1) 关机前，请将存放的食物移至另一台冷藏柜 / 冷冻
柜。
2) 拔下本机的电源插头或断开主电源。
3) 打算长时间不使用本机时，请清洁柜内部和柜门衬
垫，并将其彻底晾干，然后将本机存放在干燥场所。
III. 保养
重要
1. 在进行任何清洁或保养作业之前，请拔下本
机的电源插头。
2. 请勿触摸或打湿机械室内的零件，否则会导
致故障或停机。
3. 请勿将塑料零件放入温度超过 40℃的水中或
洗碗机中清洗，以免损坏零件。
1. 内部、外部、层板
* 为保持使用卫生，应每周清洁冷藏柜的内部和外部
至少一次。
* 将软布浸泡在由冷水或温水加适量中性清洁剂混合
而成的溶液中，然后取出软布并拧干，再使用该软
布清洁本机内部和外部。请勿用喷水器清洁机械室。
* 使用中性清洁剂以外的化学试剂可能会导致内表面
和外表面损坏。
* 任何洗涤剂残留都将损伤金属或塑料表面，因此请
使用蘸有温水的软布将其擦除。
* 请勿使用下列物品，以免其损坏喷漆或塑料表面 ：
抛光粉、酒精、稀释剂、挥发油、酸性或碱性洗涤剂、
热水、石油精、肥皂粉、金属打磨工具或刷子等。
尤其不可使用专用于清除通风设备或微波炉上油脂
的洗涤剂。
图15
空气过滤网 前板
导板
基座
插槽
图16
空气过滤网
2) 使用含有适量中性清洁剂的冷水或温水小心地清洗
空气过滤网。冲洗并彻底晾干空气过滤网。
3) 若要重新安装空气过滤网，请将其安装到冷凝器顶
部的导板上，再插入制冷机组基座的插槽中。
ⷨ
⺼
㉝
䜦
㊒
⿔
䞞
ࠖ
≑
⊍
⛁
∈
䝌
⺅
ᗻ
⋫
ࠖ
图14

中文
17
(2) 柜门未关紧。
4) 噪声 :
(1) 压缩机或冷凝器风扇的正常运转声。
5) 机械室内部结霜 :
(1) 环境湿度过高。
(2) 频繁打开柜门。
(3) 食物放入过多，超出了机器的负荷。
4. 废弃处理
对冷藏柜 / 冷冻柜进行废弃处理时，请联系授权的星
崎维修公司或专门的废品处理公司。
重要
用于机体的隔热材料发泡剂含有易燃
气体环戊烷 。请记住这一点，正确
处置冷藏柜/冷冻柜。
5. 保修
星崎向拥有者/用户保证，星崎品牌的所有产品在产品
“保修期”内不存在材料和/或工艺缺陷。产品保修在
自产品安装之日起一年内有效。
星崎在此保修条款下承担有限责任，但日常维护、清
洁、必需的保养和/或因误用以及未根据星崎的准则安
装而导致的修理除外。
保修范围内的维修应由授权的星崎经销商或维修机构
负责，且应使用纯正的星崎零件。
若要获取有关保修和授权维修机构的详细信息，请联
系经销商/供货商或最近的星崎维修办事处:
星崎冷热机械(上海)有限公司
电话：[phone]
传真：[phone]
星崎香港有限公司
电话：[phone]
传真：[phone]
台湾星崎国际股份有限公司
电话：[phone]
传真：[phone]
3. 报修前
重要
1. 如果操作面板上的显示屏显示故障代码或本
机存在故障迹象，请根据以下说明查找可能的
故障原因。如果故障仍然存在，请立即联系授
权的星崎维修公司。
2. 联系维修公司时，请向对方说明型号、序列号、
安装日期 ( 参见保修卡 ) 以及故障状况。
3. 请勿尝试自行维修本机。
[a] 显示故障代码的故障
冷藏柜
代码 可能的原因 操作和补救措施
E1
柜内传感器故障 压缩机停机。按任何按钮停止报警声。
当故障诊断结束时，系统将重新计算
压缩机延迟时间。请立即联系星崎授
权的维修公司。
E2 蒸发器故障 除霜终止温度无效。按任何按钮停止
报警声。请立即联系星崎授权的维修
公司。
冷冻柜
代码 可能的原因 操作和补救措施
HHH 环境温度
过高
压缩机以运行 45 分钟然后停止 15
分钟的方式循环工作。检查环境温度。
若问题无法解决，请立即联系星崎授
权的维修公司。
LLL 环境温度
过低
* “dF”代码并非出错代码，而是表示本机正处于除
霜过程中。
[b] 不显示故障代码的故障
1) 本机无法运转 :
(1) 未插电源插头。
(2) 停电。
(3) 主电源断开。
2) 制冷性能不佳 :
(1) 环境温度过高 (43℃以上 )。
(2) 频繁打开柜门。
(3) 柜内温度设定过高。
(4) 食物放入过多。
(5) 空气过滤网脏污。
(6) 柜门未关闭。
3) 柜门附近出现冷凝水 :
(1) 环境湿度过高。