Hot Yoga Heating HYH-32-P User manual

1-844-yoga hot
(964-2468)
USER MANUAL
HYH-32-P
UNIVERSAL THERMOSTAT

Your new HYH-32-P Universal Thermostat has been built using the highest quality components and
design currently available. As a result, when properly installed and configured by your professional
heating and air conditioning contractor, the thermostat will provide years of trouble-free operation.
The thermostat has been designed to be an attractive, highly reliable and easy-to-use thermostat. By
taking the time to read and understand this operation manual, you can take advantage of the many user
features offered in this premium product.
Great care has been taken in the preparation of this manual. Hot Yoga Heating takes no responsibility for
errors or omissions contained in this document. It is the responsibility of the user to ensure that this
thermostat, or equipment connected to it is operating to their respective specifications and in a safe
manner.
Introduction
The thermostat can be used for both residential and commercial applications. Within these
applications the thermostat can be either programmable or non-programmable. The HVAC installer
will have set these parameters to best suit your individual needs.
For clarity, this Operation Manual is broken into the following main sections:
•Residential Programmable Mode (4 schedules per day)
• Commercial Programmable Mode (2 schedules per day)
• Non-programmablel Mode
• Common Functions
The thermostat can be configured for a wide range of HVAC systems and applications requiring
specific functions. Therefore, this manual may describe a function that is not active for you specific
application.
1

MODE O/RIDE PROG FAN
Residential Programmable Mode
MODE Selection
Press the key to cycle through the modes ofMODE
operation and the LCD will display the following:
Heat Heat Mode
Cool Cool Mode
Cool
Heat
E. Heat Emergency heat when thermostat is
configured for a heat pump system
OFF Thermostat is off
Auto Changeover (Installer must
activate this mode)
Cool
Heat
MODE KEY
FAN Selection
Press the key to cycle through the fan selections. More details on fan functions can be found onFAN
page 20 of this manual.
Auto The HVAC system fan will only run with a call for heating or cooling.
On The HVAC system fan will run continuously.
FAN KEY
MODE O/RIDE PROG FAN
Cool
Heat
Setting the clock
The thermostat has a real-time clock that is used for
programming functions. It is important that the time
and day of week be set properly so that programmed
events run correctly.
To set the clock, press the key until the hourPROG
flashes on the LCD. Use the up or down arrow key to
set the current hour along with the AM and PM
symbol. Press the key again until the minutesPROG
flash. Use the up or down arrow key to set the
current minutes. Press the key again until thePROG
day flashes. Use the up or down arrow key to set the
correct day of the week. Press the again toPROG
exit the clock and day of week program.
PROG
KEY
UP / DOWN
KEYS
2

Programming 4 daily events
The thermostat can be programmed to provide 4 individual time-of-day temperature settings for each
day of the week.
Each event is noted on the LCD by numerals
At the start of each event, the programmed heating and cooling temperature will be maintained until
the next event starts.
1 2 3 4
MODE O/RIDE PROG FAN
Cool
Heat
PROG
KEY
Entering the program mode
Hold the key down for 3 seconds.PROG
The display will show the number and the day1 MON
will flash.
Use the up or down arrow key to set the day you wish
to start programming.
Press the key again and the hour will flash.PROG
Use the up or down arrow key to set the time you
wish program to start. Make sure that the AM / PM1
is correct.
Press the key again and the minutes will flash.PROG
Use the up or down arrow key to set the minutes for
program to start.1
UP / DOWN
KEYS
1
Press the key again and or will be displayed along with the temperature value. UsePROG Heat Cool
the up or down arrow key to select the desired heating or cooling temperature to be maintained for
the program time period.1
Press the key again and the opposite mode and a temperature value will be shown on thePROG
LCD. Use the up or down arrow key to select the desired temperature to be maintained for the
program time period.1
Note: There must be at least a 2 degree difference between the heating and cooling temperatures.
The heating temperature must always be lower than the cooling temperature. If you set the heating
or cooling temperature closer than the minimum value, the thermostat will automatically move one of
the temperature settings to maintain the 2 degree difference.
1
1
3