Hotpoint HL500G User manual

Instructions for Installation and Use
50cm Free Standing Eye-level Gas Cooker
HL500G
Our Ideas. Your Home
To the Installer
Before installation fill in the product details on the back cover this book.
The information can be found on the rating plate.
To the User
You must read the instructions prior to installing and using the appliance and
then retain them for future reference.
Alkaline
AA
NOTE: This appliance is fitted with a battery powered
ignition system (the battery provided). Sholud the ignition
system start to spark slowly - or not at all, the
battery will need replacing. See the section on
battery replacement.

2
Contents
Introduction 3
Installation 4
Installation of Eye-Level Grill 8
Burner and Nozzle Specifications 10
Safety Information 11
Features 13
Control Panel 14
Use of hotplates 15
Grilling 16
Oven 17
Oven cooking charts 18
Care and Cleaning / Battery Replacement 19
Cooking Results Not Satisfactory? 20
Something Wrong With Your Cooker? 21
Technical Characteristics 22
After Sales Service 26
Hotpoint Guarantee 27
Key Contacts Back Cover
You must read these instructions prior to using your appliance and retain them for
future use.

3
Introduction
Your new appliance is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance
has been installed in accordance with the installation instructions detailed in this booklet.
To help make best use of your cooking equipment, please read this booklet carefully.
The cooker is designed specifically for domestic use and responsibility will not be accepted for use in any other
installation.
When the cooker is first used an odour may be emitted,
this will cease after a period of use.
When first using the cooker ensure that the room is well ventilated (e.g. open a window or use an extractor fan) and
that persons who may be sensitive to the odour avoid any fumes. It is suggested that any pets be removed from the
room until the smell has ceased. This odour is due to temporary finish on oven liners and elements and also any
moisture absorbed by the insulation.
* The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with the Users Instruction Book.
(b) Has been properly connected to a suitable supply voltage as stated on the
rating plate attached to this equipment.
(c) Has not been subjected to misuse or accident or been modified or repaired by
any person other than the authorised employee or agent.
(d) Has been correctly installed.
1 This appliance is intended for nonprofessional use within the home.
2These instructions are only for those countries whose symbols appear in the booklet and on the serial no.plate
of the appliance.
3 This owner’s manual is for a class 1 appliance (insulated) or class 2, subclass 1 appliances (installed
between two cabinets.

4
Installation
The appliance must only be installed by a competent person. In the UK, CORGI registered installers undertake
to work to safe and satisfactory standards.
Before moving your cooker check that it is cool, and switch off at the cooker control unit.
Splashplate optional, apply to Parts Department (see Back Cover for contact number.)
The following instructions should be read by a qualified technician to ensure that the appliance is installed, regulated
and technically serviced correctly in compliance with current regulations.
Important: remember to unplug the appliance from the mains before regulating the appliance or carrying out
any maintenance work.
Positioning
Important: this unit may be installed and used only in permanently ventilated rooms according to the British Standards
Codes Of Practice: B.S. 6172/B.S. 5440, Par. 2 and B.S. 6891 Current Editions. The following requirements must be
observed:
a) The cooker should not be installed in a bed sitting room with a volume of less than 20m3. If it is installed in a room of
volume less than 5m3an air vent of effective area of 110cm2is required, if it is installed in a room of volume between
5m3and 10m3a supplementary airvent area of 50cm2 is required, if the volume exceeds 11m3no airvent is required.
However, if the room has a door or a window which opens directly to the outside no air vent is required even when the
volume is between 5m3and 11m3.
b) During prolonged use of the appliance you may consider it necessary to open a window to the outside to improve
ventilation.
c) If there are other fuel burning appliances in the same room, B.S.5440 Part 2 Current Edition, should, be consulted to
determine the requisite air vent requirements.
Installation of the cooker
For a correct installation of the cooker the following precautions must be followed:
The height of the cooker can be adjusted by means of adjustable feet in the plinth (900mm - 915mm). Adjust the feet by
tilting the cooker from the side. Then install the product into position.
NOTE:This appliance must not be fitted on a platform.
The cooker is designed to fit between kitchen cabinets spaced 500mm apart. The space either side need only be sufficient
to allow withdrawal of the cooker for servicing. It can be used with cabinets one side or both as well as in a corner setting.
It can also be used free-standing.
Adjacent side walls which project above hob level, must not be nearer to the cooker than 125mm and should be protected
by heat resistant material. Any overhanging surface or cooker hood should not be nearer than 400mm. (Fig.A)
a) The cooker may be located in a kitchen, a kitonen/diner or bed sitting room, but not in a bathroom or shower
room.
b) The hoods must be installed according to the requirements in the hood handbook.
c) The wall in contact with the back of the cooker must be of flameproof material.
d) The cooker is fitted with a safety chain that must be attached to a hook, secured to the wall behind the appliance.
125mm
Min
400mm
Min
503mm
Min
1450mm
1850mm
125mm
Min
Fig. A

5
Gas connection
The cooker should be connected to the gas-supply by a corgi registered installer. During installation of this
product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience
of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas must be
carried out according to the prescribed regulation in force, and only after it is ascertained that it is adaptable
to the type of gas to be used. If not, follow the instructions indicated in the paragraph headed “Adaptation to
different gas types”. On some models the gas supply can be connected on the left or on the right, as
necessary; to change the connection, reverse the position of the hose holder with that of the cap and replace
the gasket (supplied with the appliance). In the case of connection to liquid gas, by tank, use pressure
regulators that conform to the regulation in force. The gas supply must be connected to the left of the
appliance. Be sure that the hose does not pass through the rear of the cooker touching hot parts.
HOT PARTS
600 mm
Important: make sure the supply pressure conforms with the values shown in the table entitled “Caracteristics of
the burners and nozzles”. When the cooker is installed between cabinets (recessed), the gas connection
must be effected by an approved flexible hose with bayonet fitting (BS 669 Current Edition).The gas inlet
for the cookers is a threaded G 1/2 gas female fitting.
Connecting the gas supply
To make the connection, a flexible hose should be used corresponding to the current gas regulations which are:
•the hose must never be at any point in its lenght in contact with the “hot” parts of the cooker;
•the hose must never be longer than 1,5 metre;
•the hose must not be subject to any tension or torsional stress and it must not have any excessively narrow
curves or bottlenecks;
•the hose must be easy to inspect along its entire length to check its condition;
•the hose must always be in good condition, never attempt to repair.
Important: the installation must comply with gas safety (installation and use) regulations 1984. In all cases for the
above, by low, a qualified, corgi approved engineer must be called for installation.
Important: Before using the oven, position the oven burner deflector "A" (provided with the appliance) in the
correct place by inserting the lower tab into the support slot (see figure).
A
Disposing of the appliance
When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the
plug body and dispose of it as described above.
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of gas with respect to the gas for which it was produced
(indicated on the label attached to the lid), follow these steps:
a) replace the hose holder mounted on the appliance with that supplied in the bag of “cooker accessories”.
b) Replacing the burner nozzles on the hob:
•remove the grids and slide the burners from their housings;
•unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas

6
(see table 1 “Burner and nozzle characteristics”).
• replace all the components by repeating the steps in reverse order.
c) Minimum regulation of the hob burners:
• turn the tap to minimum;
• remove the knob and adjust the regulation screw, which is positioned in or next to the tap pin, until the
flame is small but steady.
N.B.: in the case of liquid gas, the regulation screw must be screwed in to the bottom.
• check that the flame does not turn off when you turn the tap quickly from high to low.
d) Regulating the primary air of the burners:
The primary air of the burners requires no regulation.
Adapting to different types of gas
In order to adapt the oven to a different type of gas with respect to the gas for which it was manufactured
(indicated on the label), follow these simple steps:
a) Replacing the oven burner nozzle
•open the oven door fully
•pull out the sliding oven bottom
•unscrew the burner fastening screws
V
VZ
•remove screw “V” and then the oven burner;
•Unscrew the oven burner nozzle using the socket spanner for the nozzles “Z”, or a 7 mm socket spanner,
and replace it with a nozzle suited to the new type of gas (see Table 1).
Take particular care handling the spark plug wires and the thermocouple pipes.
•Replace all the parts, following the steps described above in the reverse order.
b) Minimum regulation of the gas oven burner with thermostat:
• light the burner as described in the paragraph “the oven knob” of the instruction booklet.
• turn the knob to Max for about 10 minutes and then turn the knob to the Min setting;
• remove the knob;

7
• regulate the screw positioned outside the thermostat pin until the flame is small but steady.
N.B.: in the case of liquid gas, the regulation screw must be screwed in to the bottom.
• check that the burner does not turn off when you turn the knob from Max to Min and and when you open
and close the oven door quickly.
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
•Loosen the screws along the perimeter to remove the rear protection (see diagram)
•remove screw “V” and then the grill burner;
V
•Unscrew the grill burner nozzle using the socket spanner for the nozzles, or a 7 mm socket spanner, and
replace it with a nozzle suited to the new type of gas (see Table 1).
Take particular care handling the spark plug wires and the thermocouple pipes.
•Replace all the parts, following the steps described above in the reverse order.
N.B.: No adjustment is needed for minimum setting.
Important
On completion of the operation, replace the old rating sticker with one indicating the new type of gas used.
This sticker is available from our Service Centres.
Note
Should the pressure of the gas used be different (or vary) from the recommended pressure, it is necessary to
fit a suitable pressure regulator onto the inlet pipe in compliance with current National Regulations relative to
“regulators for channelled gas”.

8
Installation of Eye-Level Grill
1. Unpack the product.
2. Unscrew the lid which protects the gas supply connection attachment for the Grill.
3. Remove the rear cover protecting the Grill assembly, which is fixed in place with 6 screws (see photograph).
4. Join the Grill assembly to the cooker. To do this, it will be necessary to "jump" the gas attachment by folding
the Grill assembly to 45° (see photograph).
5. Fix the Grill assembly to the cooker using three screws on the right-hand side and three screws on the left-
hand side as shown in the photograph, using the screws supplied.

9
6. Join the Grill hose attachment to the cooker attachment (using a torque wrench setting of 11±2 Nm).
7. Connect the appliance electrically using the fastons on the rear part of the cooker (it makes no difference in
which order these are connected).
8. Replace the rear cover and fix it in place using the same screws (6) as removed previously in step 3 of this
procedure.

10
Burner and Nozzle Specifications
Table 1 Liquid Gas Natural Gas
Burner Diameter Thermal Power
kW (p.c.s.*)
Thermal Power
kW (p.c.s.*)
By-Pass
1/100
Nozzle
1/100
Flow*
g/h
Thermal Power
kW (p.c.s.*)
Nozzle
1/100
Flow*
l/h
(mm) Nominal Reduced (mm) (mm) *** ** Reduced (mm)
Fast
(Large)(R) 100 94 3,00 0,70 41 87 218 214 0,70 128 286
Semi Fast
(Medium)(S) 75 69 1,90 0,40 30 70 138 136 0,40 104 181
Auxiliary
(Small)(A) 51 46 1,00 0,40 30 52 73 71 0,40 76 95
Oven - 2,60 0,60 36 75 189 186 0,60 123 248
Grill - 3,60 2,40 90 94 262 257 1,40 140 343
Supply
Pressures
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
* At 15°C and 1013 mbar- dry gas
** Propane P.C.S. = 50,37 MJ/Kg
*** Butane P.C.S. = 49,47 MJ/Kg
Natural P.C.S. = 37,78 MJ/m3
SS
R
A
HL500G

11
Safety Information
When used properly your appliance is completely safe but as with any electrical product there are certain
precautions that must be observed.
PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR APPLIANCE.
Always
lRemove all packing from inside the oven and grill compartments before switching on for the first time.
lUnderstand the controls prior to using the appliance.
lKeep children away from the appliance when grilling as the surfaces will get extremely hot during and after
use.
lTurn controls off when you have finished cooking and when not in use.
lStand back when opening an oven door to allow any build up of steam or heat to disperse.
lUse dry good quality oven gloves when removing items from the oven/grill.
lPlace pans centrally over the hotplate making sure handles are kept away from the edge of the hob and cannot
become heated by other hotplate/pans.
lTake care to avoid heat/steam burns when operating the controls.
lTurn off the electricity supply at the wall switch before cleaning and allow the appliance to cool.
lMake sure the shelves are in the correct position before switching on the oven.
lKeep the oven and grill doors closed when the appliance is not in use.
lTake care when removing items from the grill when the lower oven is on as the contents will be hot.
lKeep the appliance clean, as a build up of grease or fat from cooking can cause a fire.
lFollow the basic principles of food handling and hygiene to prevent the possibility of bacterial growth.
lKeep ventilation slots clear of obstructions.
lRefer servicing to a qualified appliance service engineer.
lTake care to avoid touching heating elements inside the oven, as during use the oven becomes hot.
lBefore operating the product, remove all plastic film from the sides of the appliance.
lThe internal surfaces of the compartment (where present) may become hot.

12
Safety Information
Never
lNever line the interior of the oven with foil as this may cause the appliance to overheat.
lNever leave children unsupervised where a cooking appliance is installed as all surfaces will be hot during
and after its use.
lDo not allow children or persons who are not familiar with the appliance to use it, without supervision.
lNever allow anyone to sit or stand on any part of the appliance.
lNever store items above the appliance that children may attempt to reach.
lNever leave anything on the hob surface when unattended and not in use.
lNever remove the oven shelves whilst the oven is hot.
lNever heat up unopened food containers as pressure can build up causing the container to burst.
lNever store chemicals/food stuffs, pressurised container in or on the appliance, or in cabinets immediately
above or next to the appliance.
lNever place flammable or plastic items on or near the hob.
lNever fill a deep fat frying pan more than 1/3 full of oil, or use a lid.
DO NOT LEAVE UNATTENDED WHILE COOKING.
lNever use the appliance as a room heater.
lNever use the grill to warm plates.
lNever dry any items on either the hob or oven doors.
lNever install the appliance next to curtains or other soft furnishings.
lNever use steam cleaners.
SAFETY ADVICE IN CASE OF A CHIP-PAN FIRE
In the event of a chip pan fire or any other pan fire.
1. TURN OFF THE COOKER APPLIANCE AT THE WALL SWITCH.
2. COVER THE PAN WITH A FIRE BLANKET OR DAMP CLOTH, this will smother the flames and extinguish the
fire.
3. LEAVE THE PAN TO COOL FOR AT LEAST 60 MINUTES BEFORE MOVING IT. Injuries are often caused by
picking up a hot pan and rushing outside with it.
NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force
of the extinguisher is likely to tip the pan over.
Never use water to extinguish oil or fat fires.

13
Features
ADJUSTABLE FEET
CONTROL
PANEL
GRILL
EYE-LEVEL
OVEN
1900W 1900W
1000W 3000W
GRILL/MEAT PAN
WITH HANDLE AND
WIRE FOOD
SUPPORT
DRAWER

14
Control Panel
LEFT
FRONT
BURNER
RIGHT
REAR
BURNER
LEFT
REAR
BURNER
RIGHT
FRONT
BURNER
ELECTRONIC
IGNITION
BUTTON
OVEN GRILL
Control Knobs
for the gas
burners
The position of the gas burner controlled by each one of the knobs is shown by a solid ring •. To light
one of the burners, hold a lighted match or lighter near the burner and, at the same time, press down
and turn the corresponding knob counter clockwise to the maximum setting. Each burner can be
operated at its maximum, minimum or intermediate power. Shown on the knob are the different symbols
for off • (the knob is on this setting when the symbol corresponds with the reference mark on the
control panel), for maximum and minimum .To obtain these settings, turn the knob counter
clockwise with respect to the off position. To turn off the burner, turn the knob clockwise until it stops
(corresponding again with the • symbol).
Electronic
Ignition
for the Gas Hob*
This device operates when a slight pressure is applied to the button marked with symbol.To light a
specific burner just press the button while pushing the corresponding knob all the way in and
turning it counter-clockwise until it lights. For immediate lighting, first press the button and then
turn the knob.
Important: Should the burner flames accidentally go out, turn off the control knob and wait
at least 1 minute before trying to relight.
* (only available on certain models)

15
Use of Hotplates
Practical Advice on Using the Burners
To use the burners as efficiently as possible, some basic guidelines should be followed:
•Use cookware that is the right size for each burner (see table) in order to prevent the flame from spreading
beyond the bottom of the cookware.
•Only use cookware with flat bottoms.
•As soon as the boiling point is reached, turn the knob to the lowest setting.
•Always use lids with pots and pans.
Burner ø Cookware diameter (cm)
Fast (R) 22 - 24
Semi Fast (S) 16 - 20
Auxiliary (A) 10 - 14
N.B.: On models equipped with a reduction grid, the grid should only be used with the auxiliary burner when
cookware with a diameter of less than 12 cm is used.
1. To light a specific burner push the corresponding knob all the way in and turn it counter-clockwise to
maximum keeping it pressed down until the burner lights.
2. To turn the control knob anti-clockwise to the desired setting. Only turn the control knob between the
large flame symbol and the small flame symbol for adjusting the setting.
3. To turn off, turn the control knob fully clockwise to the symbol O.
DO NOT use the hotplate unless all pan supports are in position.
DO NOT use mis-shapen pans which may be unstable.
DO NOT use round base woks directly on the pan supports.
DO NOT use the glass lid (if fitted) as a working surface.
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid lighting of the burners every time they
are used, the ignitors must be kept clean and dry. Remove any food spillage or cleaning materials from the
electrode using a small nylon brush such as a tooth brush. Access to the electrode can be achieved by lifting off the
loose burner parts carefully when the burners are cool.
When the hotplate burner bodies and caps are removed for cleaning, be careful not to drop any food particles or
cleaning materials into the burner bases, to avoid the possibility of blocking the gas jets.
If aluminium based pans are used, a silvery deposit may appear on the top edge of the pan support fingers. See
'Care and Cleaning' section for cleaning information.
SAFETY REQUIREMENTS FOR DEEP FAT FRYING
1. Never fill chip pans more than one third full with oil or fat.
2. Never leave oil or fat unattended during the heating or cooling period.
3. Never heat fat or fry with a lid on the pan.
4. Always dry food thoroughly before frying, and lower it slowly into the hot oil or fat. Frozen foods in
particular will cause frothing and spitting if added too quickly.
5. Always keep the outside of the pan clean and free from streaks of oil or fat.
HOW TO DEAL WITH A FAT FIRE
1. Do not move the pan.
2. Turn off the hotplate burners.
3. Smother the flames with a fire blanket or damp cloth to extinguish the fire. Do not use water or a fire
extinguisher as the force of it may spread the burning fat or oil over the edge of the pan.
4. Leave the pan for at least 60 minutes before moving it.

16
Grilling
CAUTION: ACCESSIBLE PARTS WILL BECOME HOT WHEN THE GRILL
IS USED - CHILDREN SHOULD BE KEPT AWAY.
To operate the grill proceed as follows:
lPress the ignition button and then push in and turn the grill control knob anti-clockwise to the large
flame symbol. Continue to press the ignition button until the spark lights the gas.
Grill Pan Handle lOnly turn the control knob between the large flame symbol and the small flame symbol for adjusting
the setting.
lTo turn off, turn the control knob fully clockwise to the symbol O
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat, intensify the heat and create a fire hazard.
Grilling can be started from cold but for best results preheat for approximately two minutes. Most
cooking is done with the heat on full, but it may be desirable to reduce it for thicker pieces of meat, fish,
chicken portions or for keeping food warm.
For au gratin dishes eg. Macaroni Cheese and meringue toppings eg. Baked Alaska, place the dish on
the floor of the grill compartment.The base of the grill pan can be used for warming fruit garnishes on
the reduced setting.
NOTE: Strong detergents used in dishwashers may damage the grill pan grid finish; clean in soapy
water as described in CARE AND CLEANING section.
Relighting
the burner
In the event of the burner flames being accidentally extinguished, turn off the burner control and do not
attempt to re-ignite the burner for at least one minute.

17
Oven
The oven has different heat zones - the thermostat settings refer to the temperature on the
middle shelf; above this shelf it is hotter and below it is cooler. Two shelves enable full use of the
temperatures inside the oven.
Each shelf has a safety stop to prevent if from being pulled out too far when attending to food.
Shelves are removed from the oven by pulling them out to the stop and then lifting them at the
front to withdraw.
The grill pan without the handle can be used in the oven. The maximum size of baking tray that
should be used is 300mm x 330mm (12" x 13").
TO USE THE OVEN 1. Place oven shelves in the chosen positions (refer to cooking charts).
2. Press the ignition button and then push in and turn the oven control knob fully anti-clockwise.
Continue to press the ignition button until the spark lights the gas.
3. Turn the control knob clockwise to the required setting (refer to cooking chart). There is a delay of
about six seconds whilst the safety device operates before the burner comes on full.
4. To turn off, turn the control knob fully clockwise the the symbol 0.
Never place dishes on the oven base over the burner.
An odour may be noticed when first using the oven - this should cease after a short period of use.
5. The oven temperature control marking are gas marked 0 to 9.
The equivalent degrees Celsius (sometimes called Centigrade) are shown below as a guide.
Oven Setting Temperature °C
1 145
2 160
3 175
4 190
5 205
6 222
7 240
8 250
9 260
RELIGHTING
THE BURNER
In the event of the burner flames being accidentally extinguished, turn off the burner control and
do not attempt to re-ignite the burner for at least one minute
COLD START
COOKING
Anything requiring long slow cooking such as casseroles and rich fruit cakes can be put into a
cold oven. Satisfactory results can also be obtained with creamed mixture, rich pastries or yeast
mixtures, but for perfection we recommend preheating the oven for about 15 minutes.
ROASTING OF
LARGE POULTRY
The maximum weight of poultry that can be accommodated is 8kg (18 Ibs) of suitable shape. It is
important to check that the bird DOES NOT overhang the burner at the back of the oven.
STORAGE AND
RE-HEATING
OF FOOD
It is vitally important to strictly adhere to the basic principles of food handling and hygiene to
prevent the possibility of bacterial growth.
1. If food is to be frozen or not served immediately, cool it in a clean container as quickly as
possible.
2. Completely thaw frozen food in the refrigerator before reheating.
3. Re-heat food thoroughly and quickly either on the hotplate or in a hot oven, Mk. 6, and then
serve immediately.
4. Only re-heat food once.
‘COOK CHILL’
DISHES
These should always be placed in a pre-heated oven ideally on the first or second shelf position.
Follow the packet instructions for cooking time.
ALUMINIUM FOIL If using Aluminium Foil:
1. Remember that it is important to increase the cooking time by one third.
2. Never allow the foil to touch the sides of the oven.
3. Never cover the oven interior with foil.
4. Never cover the oven shelves with foil.

18
Oven Cooking Chart
The following times and setting are for guidance only. You may wish to alter the setting to give a result more to your
satisfaction. When a different setting to that shown below is given in a recipe, the recipe instructions should be
followed. Allow 15 minutes preheat for best results. Always turn the thermostat knob to Mark 9 before selecting the
appropriate gas Mark. Shelf position 1 is the highest.
Food Gas
Mark
Shelf
Position
Approx. Cooking Time and Comments
Fish
Oily and white fish 3 or 4 4 25-60 mins. depending on recipe
Meat and Poultry
Beef 4 or 5 4 25-30 mins per 450g (1 Ib) + 25 mins. extra
Ham 5 4 40 mins per 450g (1 Ib) covered in foil plus 40 mins.
extra
Lamb 5 4 30 mins per 450g (1 Ib) + 30 mins extra
Pork 5 4 40 mins per 450g (1 Ib) + 40 mins extra
Chicken 5 4 25 mins per 450g (1 Ib) + 25 mins extra
Duckling & Goose 5 4 25 mins per 450g (1 Ib) + 25 mins extra
Turkey 4 or 5 4 or 5 15-20 mins per 450g (1 Ib) + 20 mins
Casseroles 3 3or4 2-6 hrs. depending on cut of meat
Vegetables
Baked jacket potatoes 4 or 5 3 1½ - 3 hrs. until soft, depending on size
Puddings
Milk Puddings (500ml/1 pt) 3 4 1¾-2½ stand dish on baking tray and started with
warm milk
Baked Custard (500ml/1 pt) 3 4 45-60 mins. bain-marie
Baked Sponge Puddings 4 3 40-50 mins
Baked Apples 3 3 30-45 mins depending on type and size of apples
Meringue Topped Puddings 1 3or4 15 mins or until "tinged" with brown
Apple Tart (1 x205mm/8//) 6 2 45-60 mins
Fruit Crumble 5 2 35 -45 mins
Cakes, Pastries & Biscuits
Small Cakes 2 trays 5 2 and 4 15-25 mins.
1 tray 5 2 15-22mins.
Victoria sandwich (2 x 7" ) 4 2 and 4 20-30 mins
Swiss Roll (3 egg quantity) 5 2 15-20 mins.
Meringues 1 3 2-3 hrs
Christmas cake (1 x 205mm / 8") 2 3 Time depending on recipe
Madeira cake (1 x 180mm / 7") 4 4 1¼-1½ hrs.
Rich Fruit cake (1 x 180mm / 7") 2 4 Time depending on recipe
Scones 7 1 and 3 10-20 mins.
Shortbread (1 x 180mm / 7") 2 3 55 -65 mins.
Biscuits 4 1 and 3 10-20 mins.
Shortcrust Pastry 6 2 15 - 60 mins depending on use.
Rich Short Crust 5 1 and 3 20-30 mins.
Flaky/Puff Pastry 7 2 10-30 mins.
Choux Pastry 6 2 20-30mins.
Yeast Mixtures
Bread - rolls 7 2 and 4 20-30 mins.
Miscellaneous
Yorkshire Pudding:- large 7 1 30-40 mins
individual 7 2 20-30mins
When baking with two trays or tins on two levels, the top tray is removed first and the lower tray moved up to the top
position for a few minutes longer.
Soft Margarine -
Use the oven settings recommended by the margarine manufacturer and not those indicated on the cooking chart.

19
Care and Cleaning
Grill Remove the grill pan and the wire grid food support, it is best to wash these items immediately after
use to prevent stains from being burnt on when used again. Wipe out the Grill compartment, use a fine
steel wool soap pad to remove stubborn stains from the grill runners and the floor of the compartment.
Wipe over the control panel with a damp cloth and polish with a dry cloth.
Control Panel Do not use cream cleaners, oven cleaners or aerosols, scouring pads or abrasive powder for
cleaning the plastic knobs as damage will occur.
Decorative Trims It is advisable to clean the decorative trims regularly to prevent any build up of soiling.The
recommended method of cleaning is to wipe over the trims with a soft cloth wrung out in warm water or
mild non-abrasive cleaner. (If in doubt try the cleaner on a small area of trim which is not noticeable in
normal use). Then, after wiping with a cloth wrung out in clear water, dry with a soft clean cloth.
Doors Wipe over the outer door glass panels with a cloth wrung out in warm soapy water, then after wiping
with a cloth wrung out in clear water, dry with a soft clean cloth. Ensure that glass doors are not
subjected to any sharp mechanical blows.
Glass Inner Door Panel (where fitted) – open the door fully and unscrew the two screws securing
the glass panel, taking care not to allow the glass to fall. The glass panel may now be washed at the
sink. Stubborn stains can be removed by using a fine steel wool soap pad. Ensure the glass panel is
not subjected to any sharp mechanical blows. Take particular care not to damage the inner
surface which is coated with a heat reflective layer. After cleaning, rinse and dry with a soft cloth. For
slight soiling the inner glass panel may be cleaned, while still warm, without removing it from the door.
Warning: Oven must not be operated with inner door glass removed.
Take care during cleaning not to damage or distort the door seals. Do not lift the door seal from the
oven chassis, if necessary remove the seal by carefully unhooking the corner clips.
Take care that the rating label edges are not lifted during cleaning, and furthermore that the lettering is
not blurred or removed.
Ovens Remove the rod shelves and grill pan. Use a fine steel wool soap pad to remove stubborn stains from
the rod shelves, grill pan and the floor of the oven. Clean the glass part of the oven door using a
sponge and a non-abrasive cleaning product, then dry thoroughly with a soft cloth. Do not use rough
abrasive material or sharp metal scrapers as these could scratch the surface and cause the glass to
crack.
Oven Shelf
Supports
The shelf supports are removable and dishwasher safe.
To remove hold the support at the front and pull away from the oven side, this can then be cleaned in
a sink or a dishwasher.When removed it allows access to the oven side, which can be cleaned with
warm soapy water.
To refit the support, insert the longer leg into the rear fixing hole and push in the front leg.
Replacing
the Battery
The battery is not covered bye the guarantee. Use an alkaline AA battery.The battery holder is located
in the plinth panel below the oven door. Open the oven door fully. Press the tag on the left hand side of
the battery holder/cover and withdraw it just enough to get access to the battery. Fit the new battery
with the end marked “+” on the same side of the battery holder as the red lead. Replace the battery
holder by pushing it firmly into the hole in the plinth.

20
Cooking Results Not Satisfactory?
Problem Check
Grilling
Uneven cooking front to
back
Ensure that the grill pan is positioned centrally below
the grill element.
Fat splattering Ensure that the grill is not set to too high a
temperature.
Oven Baking
Uneven rising of cake
Ensure that the oven shelves are level by using a
spirit level on the rod shelf and adjusting, using
suitable packing e.g. wood, under the feet of the
appliance. This should be checked both left to right
and front to back. Ensure that the food is positioned
centrally in the oven.
Sinking of cakes The following may cause cakes to sink:
1. Cooking at too high a temperature.
2. Using normal creaming method with soft margarine.
Over/Under cooking
Fast/Slow cooking
Refer to the cooking times and temperatures given in
the oven temperature charts, however, it may be
necessary to increase or decrease temperatures by
10°C to suit personal taste.
Do not use utensils greater than 2¼ ins in height.
Uneven cooking of
cakes
1. Too large baking sheet used. (See 'Cookery Notes')
2. Over loading of oven and always ensure even air
gaps around baking tins.
Uneven rising of cake Ensure that the shelf is level (see above) and that the
food is positioned centrally in the oven.
Food is taking too long
to cook
Only cook one item at a time to avoid overloading the
oven.