Hotpoint E320SKIX User manual

3
GB
Index
Instructions for use
Installation, 4
Use, 4
Maintenance, 4
Instructions for the installater
Installation, 6
Positioning, 6
Electrical connection, 6
Assistance, 7
THIS APPLIANCE IS CONCEIVED FOR
DOMESTIC USE ONLY.THE MANUFACTURER
SHALL NOT IN ANY WAY BE HELD
RESPONSIBLE FOR WHATEVER INJURIES
OR DAMAGES ARE CAUSED BY INCORRECT
INSTALLATION OR BY UNSUITABLE,WRONG
OR ABSURD USE.
English
GB
Dear customer,
We thank you and con-gratulate you on your
choice. This new carefully de-signed product,
manu-facturedwiththehighestqualitymaterials,
has been carefully tested to satisfy all your
cooking demands. We would therefore request
you to read and follow these easy instructions
which will allow you to obtain ex-cellent results
right from the start. May we wish you all the
very best with your modern appliance!
THE MANUFACTURER
Electrical Cooking Hob
E320SKIX

4
GB
Instructions for use
USE OF ELECTRICAL PLATES
quick-normal intensity of heat
1 Weak
2 Gentle
3 Slow
4 Medium
5 Strong
6 Bright
Fig.1
Fig.2
Installation
All operations relative to installation (electric connection)
should be carried out by skilled personnel in conformity
with the rules in force. As for the specific instructions see
part pertaining to installer.
Use
Electric plates (Fig. 1 - 2 - 3)
Rotate the knob to the position correspondent to the
needs of cooking taking into consideration that to a
higher number a higher heat supply corresponds,
see table “use of electric plates”. “Quick and normal
plates”: clockwise and anticlockwise rotation with
7 fixed position (0÷6). The pilot lamp on indicates
when plate is connected.
Some types of pilot lights will maintain some slight
luminescence even after disconnection. That is quite
normal.
N.B.:
- When one makes use of electric plates, we advise
receptacles with flat bottom having same diameter or
lightly higher than that of the plate;
- avoid overflows of liquid, therefore when boiling
has happened or in any case when liquid is heated,
reduce the heat supply;
- don’t leave the electrical plates on without receptacles
on the top or with void pots and pans;
- at the end of cooking take again the knob to position “0”.
Maintemace
Before every operation it’s necessary to disconnect the
apparatus. To obtain a higher life of the apparatus concerned
it’s indispensable to carry out at regular intervals a carefully
general cleaning bearing in mind the following:
- the s/s and/or enameled parts should be cleaned by
means of suitable not abrasive or corrosive products
(available on the market). Avoid cloride-base products
(bleach, etc.)
- avoid leaving on the top acid or alkaline substances
(vinegar, salt, lemon-juice, etc.)
- the electric plates have to be cleaned by means of a wet
rag and lightly oiled with lubricant when they are still tepid.
DO NOT USE STEAM CLEANERS

5
GB
HO5RR - F3 x 1.5
HO5RR - F4 x 0.75
Apparatus class I (type Y): it can be brought near furniture being higher than the work-top
ELECTRIC PLATES
SUPPLY TYPE WREGULATION
~ 230 V • QUICK Ø 145 1500
CLOCKWISE AND ANTICLOCKWISE ROTATION
• QUICK Ø 180 2000
• red pointFig. 4
Fig. 5
1 - Ø 145
2 - Ø 180
Fig. 3

6
GB
Instructions for the installer
Installation
These instructions are turned to the skilled installer as
a guide toinstallation, regulationand maintenance in
compliance with the lawsand the rules in force. Any of
these operationsmust always be carriedout when the
appliancehas been disconnected from the electric
system.
Positioning (Fig. 4)
The apparatus isprovided to be built-in awork-top
as shown in thespecial figure.Present the sealing
agentalong all the perimeter.
Electrical connection (Fig. 5)
Before carrying out theelectrical connection be sure that:
- the characteristics of the system are such as tosatisfy
what indicated onthe part number plateapplied to the
bottom ofthe work-top;
- that the system is provided with the effective ground
in compliance with the rules and the provisions of law
in force. The ground is binding according to the law.
In case the apparatus isn’tprovided with cable and/or
with relative plugmake use of material suitable for the
absorption indicated inthe part number plate andfor
the workingtemperature. The cableshould reach in
no point atemperature higher 50°Cthan of the room
temperature.
If connecting directly to the mains power supply, fit a multi-
poles witch of a suitable size for the rated capacity with
a clearance distance which completely disconnects the
power line under over voltage category III conditions,
consistently with the rules of installation (the yellow/green
earth wire must not be interrupted).
The plug on the omnipolarswitch should be easilyreachable
with apparatusinstalled.
N.B.:-Themanufacturerdeclinesallresponsibilityincase
the above and the usual safety rules aren’trespected.
To avoid all risk, if the powercable becomes damaged,
it mustonly be replaced bythe manufacturer, byan
authorised service centre, or by aqualified electrician.

7
GB
The manufacturer declines all responsibility for possible inaccuracies contained in this pamphlet, due to printing or
copying errors. We reserve the right to make on our own products those changes to be considered necessary or useful,
without jeopardizing the essential characteristics.
Assistance
Before contacting After-Sales Service:
1. See if you can solve the problem yourself.
2. Switch the appliance on again to see if the problem
has been solved. if it has not, disconnect the
appliance from the power supply and wait for about
an hour before switching on again.
3. If the problem persists after this course of action,
contact After-Sales Service.
Specify:
• the nature of the fault,• the model• the service number (the number after the word SERVICE on the rating plate on the rear of the
appliance)
• your full address,• your telephone number and area code.Never call on unauthorized technicians and always
refuse to purchase non-original spare parts.

9
Notes

Morley Way, Peterborough, PE2 9JB, Englandwww.hotpoint.co.uk
Cod. 1.007.23.0