Hotpoint RA720 Operating instructions

ge.com
Safety Instructions ........ 2-4
Operating Instructions
O_en .................... 6-9
Surface Units ................ 5
Care and Cleaning
Broiler Pan and Grid ........ l l
Cooktop ............... 10, 11
Knobs .................... 12
Oven Door . ............... 11
Oven Heating Elements ...... 11
Oven Interior .............. 12
Painted Surfaces ............ 19
Shelves ................... 10
Surface Units and Drip Pans ...10
Installation Instructions
Anti-Tip Device .......... 13, 19
Dimensions and Clearances ... 14
Electrical Connections ..... 15-18
Flooring .................. 14
Leveling .................. 19
Preparation ................ 14
Tools You Will Need ......... 14
Troubleshooting Tips ....... 20
Consumer Support
Consumer Support... Back Cover
Product Registration ...... 21,22
Warranty .................. 23
Write the model and serial
numbers here:
Model #
Serial #
You can find them on a label
under the cooktop. See the
I,ift-Up Cooktop section in this
tl/aIltlal for ilIstItlctiolls oi1 how
to lift the cooktop. 183D9541PO02
HOTPOINT
t7,4720
17A724
49-88025 12-05J17

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
ii}i;i{iii_!iiiiiii
AWARNING!
For your safe_, the information in this manual must be followed to minimize the risk of fire or
explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
ANti-TIPDEVICE
All rangescan tip and injury could result.
Toprevent accidental tipping of the range, attach it to the waft by installing the Anti--tip
device supplied.
If the Anti--tip device supplied with the range does not fit this application, use the universal Anti--17p
device WB2X7909.
Tocheck if the device is installed and engaged properly, carefully tip the range forward. TheAnti--tip
device should engage and prevent the range from tipping over.
If yon pnll tile range ont fronl tile wall for ally' reason, n/ake snre tile device is properly
engaged when yon push tile range back against tile wall. If it is not, theie is a possible risk of
tile range tipping over and causing iiIjni T if yon or a child stand, sit or lean on an open door
Please refer to tile Axlfi-Tip device infoi_nafion ill this mamlal. Failure to rake this piecaufion
could resnh ill tipping of tile rang> and inju U.
SAFETYPRECAUtiONS
When using electrical appliances, basic safety precautions should be foflowed, including the following:
• Use this appliance only for its intended • Doll t allow anyone to climb, stand or
use as described in this n/anna].
•Be snre yonr appliance is properly
installed and grounded by a qualified
mchnician ill accordance wifll tile
provided installation insunctions.
• Don't attempt m repair or ieplace any
part of your rang_ unless it is specifically
iecomnmnded in this manual. All other
servicing should be refeIxed m a qualified
mchnician.
• Before perforn_ing any service
recomn/ended in fllese instructions,
DISCONNECT THE RANGE PO_4:ER
SUPPI,Y AT THE HOUSEHOI,D
DISTRIBUTION PANEL BY REMOVING
THE FUSE OR SWITCHING OFF THE
CIRCUIT BREAKER.
• Do not leme children alone---children
should not be left alone or unattended in
all area where an appliance is ill use. They
should nexer be allowed to sit or stand on
any part of tile appliance.
hang on tile door or rang_ top. They
could damag_ file range and even tip it
ox_I; causing sex.re personal iiijui>
•CAUTION: ITEMS OF INTEREST TO
CHILDREN SHOULD NOT BE STORED
IN CABINETS ABOVE A RANGE OR
ON THE BACKSPIASH OF A RANGE--
CHILDREN CIJMBING ON THE
RANGE TO REACH ITEMS COUI.D
BE SERIOUSI XINJURED.
• Ne_er wear loose-fitting or hanging
gamlents while using tile appliance.
Flamnlable material could be ig_ited
if brought in contact Mill hot heating
elements and may cause sex>re bnixls.
• Use only d Upot holders--moist or damp
pot holders on hot snrtZaces may result in
btn_ls from smam. Do not let pot holders
touch hot headng elen/ents. Do not use a
towel or other bulky cloth.
• For your safeff, nexer use your appliance
for wam_ing or heating tile room.
• Storage in or on appliance--Flanmlable
materials should not be stored in an oxen
2or Ileal sniiCace nnits.

ge.com
xAWARNING!
2 'T. SAFETYPRECAUTIONS
2.-,__ •Kee I) hood and grease fihers clean to
/_'r_ _ maintain good ,enting and to axoid
grease fires.
•Do not let cooking grease or other
flammable mamfials accunnflate in or
near tile rang_.
• Do not use wamr on gxease fires. Nexer
pick up a flaming pan. Smother flaming
pan on surface unit by covering pan
completely with well-fitting lid, cookie
sheet or fiat tray. Flaming grease outside a
pan carl be put ont by co\Piing XVJfl/
baking soda oI; if available, a multi-
purpose drT chemical or foam-wpe fire
extinguisher
Do not touch heating elements or inmi-ior
surtZace of oven. These surt_aces m W be hot
enough to bum exen though they are dark
in color During and after use, do not
touch, or let clothing or other flammable
mamfia]s contact surthce units, areas
nearby the surface units or any interior
area of rile oven; allow sufficient time for
cooling first.
Pomnfially hot s/lrP,tces include tile
cookmp and areas facing file cookmp,
o\>n vent opening and surt_aces near file
opening, and crevices around file oven
door Remember: Tile inside surt_ace of rile
ox>n m W be hot when rile door is opened.
COOKMEATANDPOULTRYTHOROUGHLY...
Cookmeat andpoultry thoroughly--meat toat least an INTERNALtemperatureof 160°Fandpoultry
toat least an INTERNALtemperatureof 180°ECookingto thesetemperaturesusuallypretects against
foodbomeillness.
!OVEN
/. Stand away from range when opening oven door. Hot air or steam which escapes can cause bums
to hands, face and/or eyes.
• Don't heat unopened food conminei3 in
tile oven. Pressure could build up and tile
container could bnrst, causing an injury.
• Kee I) oven free fiom giease buildup.
• Place oven shelf in desiied po0tion while
oxen is cool. If shehes mnst be handled
when hot, do not let pot holder contact
heating elements in file ox>n.
• Pulling ont shelf to tile shelf stop is a
com>nience in lifting hemy' foods. It
is also a precaution against bums flom
touching hot surfaces of rile door or
OXPI1 walls.
• When using cooking or roasdng bags in
ox>n, tbllow tile manufi_cturer's directions.
• Do not use your ox>n to drT newspapers.
If oveflmamd, they can catch fire.
• Kee I) tile oxen x_nt ducts unobstrucmd.
3

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
SURFACECOOKINGUNITS
Use proper pan size--This appfiance is equipped with one or more surface units of different size.
Select cookware having fiat bottoms large enough to cover the surface unit heating element. Theuse
of undersized cookware will expose a portion of the heating element to direct contact and may result
in ignition of clothing. Proper relationship of cookware to surface unit will also improve efficiency.
• Nex_r leax_ surl_ace units unattended at
high heat settings. Boilox>r causes smoking
and g_easy spillox_rs that may catch on
fi re.
• Be sure dlJp pans axe in place. Their
absence dining cooking could damag>
range parts and wiring.
• Don't use aluminuna foil m line &ip
pans oi anywhere in file o_>n except as
described in this guide. Misuse could
resuh in a shock, fire hazard or damag>
m the rang>.
• Only certain types of glass, glass/ceramic,
earthenware or oilier glazed containers are
suitable for rang>-mp seIMce; others may
break because of the sudden change in
temperature.
• To minimize the possibility of burns,
ig_ifion of flammable materials and spillage,
the handle of a container should be turned
toward the cenmr of the range withotlt
exmnding ox>r nearby smfltce units.
•A]wws tux_l surface unit to OFFbefore
renlo\'ing cookware.
• Keep an eye on foods being tided at HI or
MEDIUM HIGH heats.
• To axoid die possibili U of a bum or
electric shock, always be certain that the
controls for all suri_tce units are at OFF
position and all coils are cool before
attempting to ]ift oi remo\> the unit.
• Don't immerse oi soak removable surface
units. Don't put fllem in a dishwasher
• Do not flame foods on die cookmp. If you
do flame foods under the hood, mm file
fail Oil.
• Foods for flTing should be as &T as
possible. Frost on frozen foods or moisul_e
on fiesh fbods can cause hot fat to bubble
11I) and ox>r sides of pan.
• Use little flit for efl>ctive shallow or deep-
fat flTing. Filling the pan mo fldl of i_atcan
cause spilloxers when tbod is added.
• If a combination of oils or fats will be used
in flTing, sot togedler befoie headng, or as
fats melt slowly.
• Alwws heat fat slowl> and watch as it heats.
• Use a deep-flit dlennomemr whenexer
possible to prexent ox>dleating fat beyond
the smoMng point.
• Use exneme caudon when mo_ing a grease
filled pan or disposing of hot g_ease.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS
4

Usingthesurface units, ge.com
Throughout this manual, features and appearance may vary from your model.
Surface Cooking Controls
Yoursurfaceunitsandcontrolsarefleslgned
togiveyoua varietyofheatsettingsforsurface
unitcooking.
Mboth LO and HI positions, there is
a slight niche so control clicks at those
positions; HI marks tile highest setting;
tO, the lowest setting.
In a quiet kitchen, you may hear
slight clicking so/mds dining cooking,
indicadng heat settings selected are being
maintained.
SMtching heats to higher settings ahvavs
shows a quicker change in temperatm'e
than switching to lower settin *s
How to Set the Controls
[] Push tile control knob in.
[] Tm'n either clockwise or
cotmterclockwise to desired
heat setting.
Control n/ust be pushed in to set only
fl'om tile OFFposition.
X,_hen control is in any position
other than OFF,you can ttlrn it without
mshin_* in.
Be StlI'e x,Otl ttlYn control to O_ when
xou finish cooking. An indicator light
will glow when ANY sm'fi_ce refit is on.
A Burner On indicator light xfill glow
when any surli_ce trait is on.
OFF
Medium
low Ifigh
Heat Setting Guide
HI -Quick start fi)r cooking; bring water
to boil.
MEDIUM HIGH-Fast fl'x pan broil;
maintain fi_st boil on large amount
of food.
MED- Saute and brown; maintain slow
boil on lmge amotmt of food.
MEDIUM LOW- Cereal; maintain serving
temperature ot most toods.
LO- Co()k after starting at HI; cook
with little water in coxered pan. Use to
steam rice,
NOTE."
At HI or MEDIUM HIGH, never leave
i¢ i fi)od tmattended, goiloxe_s cause
smoking; greas) si)illoxe_ may
catch fire.
[_] At LO,melt chocolate, butter on
small mfit.
Cooking tips
•Use medium- or hea\)_veight
cookware. Ahllllintlil/cookware
conducts heat fi_ster than other
metals, Cast-iron and coated cast-iron
cookware is slow to [ibsoi'b heat,
but generally cooks evenly at low or
medium heat settings. Steel pans may
cook tmevenlv if not combined with
other metals.
• Do not overfill cookware with fat
that may spill over when adding t0od.
Frosty foods bubble vigorousl> Watch
foods fl')ing at high temperatures.
Kee I) range and hood clean fl'om
accumulated grease.
• To conserve tile nlost cooking energ)';
pans should be fiat (m tile bottom,
have straight sides and tight-titting
lids. Match the size ot the saucei)an
to tile size of tile stu'fi_ce unit. A pan
that extends more than an inch
beyond tile edge of tile drip pan
traps heat, which causes "crazing"
(fine hairline cracks) on porcelain,
and discoloration ranging from blue
to dark gray on chrome drip pans.
5

Usingtheoven.
The OVEN TEMPknob is located on the control panel on the front of the range.
OVEN @TEMP Oven TemperatureControl
To use the oven, simply mrn the knob
to the desired cooking temi)eramres ,
which are marked in 25°F increments
on the dial. OVEN TEMP maintains the
teinperature you set, fl'oin 200°1:t(> BROIL.
TheOvenCyc/i)_gbghtg/owsuntiltheoven
reachesyourselectedtemperature,thengoesoff
andonwith theovenunit(s)dun?)gcookl?)g.
Bum Oven Shelves
The shelves are designed Mth stop-locl<s
so when placed correctly on the shelf
sui)ports, they will stop beflwe coming
complemly Otlt of the oven and will not
tilt when um are removing fl)od ti'om
them or placing fi)od on them.
When plating cookware on a shell, pull
the shelf out to the bump on the shelf
sui)port. Place the cookware on the
shelf, then slide the shelf back into the
oven. This will eliminate reaching into
the hot oven.
Toremove the shelves from the oven, pull
them toward you, tilt fl'ont end Ul)ward
and pull them Otlt.
Toreplace, place shelf on shelf suI)port
with stoI>locl<s (curved exmnsion of
shelf') fi_dng up and toward back of oven.
Tilt up ti'ont and push shelf toward back
of oven until it goes past the bum I) on
the shelf supI)ort. Then lower ti'ont of
shelf and push it all the way back.
1
Theovenhas4shelfpositions.
OvenShelf Positions
The oven has four shelf SUl)ports_
(bottom), B, Cand O(top).
Shelf positions fl)r cooking are suggested
on Baking and Roasting pages.
UseofAluminumFoil
• It desired, a sheet ol ahlI/lintlIll
toil may be used on the floor of the
oven under the bake element.
Be certain foil doesnot touch bake
element _uminum fi)il used in this
way may slightly atti_ct the browning
of some foods. Change fi)il when it
becomes soiled.
•DONOT place a sheet of aluminum
foil on the shel£ To do so may result
in improperly cooked fi>ods, damage
to oven finish and increase in heat
on outside surfaces of the oven.
You may use ahmfinum fi)il to line the
broiler pan and broiler grid. However;
you Inust n/old the fi)il tightly to the
grid and cut slits in it just like the grid.

Usingthe ovenforbakingormasting, gecom
Toavoid possible bums, place the shelves in the desired posifion before you turn the oven on.
How to Set Your Oven for Baking or Roasting
[]
[]
Position tile sheff or shelves in the
(wen. If cooking on two shelves at
the sanle tiine, stagger the l)ans for
best heat circulation.
Chise ox, en dooi: mlli'n
OVENTEMPkalob clock_ise to
desired teini)eiature. Preheat oxen
for at least lO ininutes if i)reheafing
is necessa i5'.
] Place t()()d in ox, en on center of
shelf. _Mlow at least 2 inches between
edge of bakeware and o_en wall or
ac!jacent cookware.
[] Check food fi)r doneness at
nlininlunl tiine on i'ecipe. Cook
longer if necessai 3. Turn OVEN
TEMP k,lob to OFF and i'eino,,e
_oo(l.
Sheff Positions
• Most baking is done on the second
shelf I)ositiInl (B) or the third shelf
I)osifion (C) fl'oni the bottom.
y - . - ,
• _._q/en l)akiil_ thIee oi four lteIns, use
two shelves positioned on the second
and fourth sets of suI)I)orts (B & D)
fl'oin bottoni of o'_eil.
• Bake angel fi)od cakes on fiI_t shelf
i)osition (A] fl'oni bottoni of o_ei1.
• Roasting is usually done on the 1)ottoin
shelf position (,4).
Preheating
• Preheating the o_en takes about 10
ininutes.
• Preheat the ()veil ()ill)' when necessary,
usually fi)I" 1)a!dng
• Most roasts will cook satisti_ctorilv
without i)reheating.
• If you find i)reheating is necessary,
kee I) an eve Oil the Oven Cycle light
and put food in the oven i)ronli)tly
after the light goes out. The Oven
Cycle light will then cycle on and off
with the ()veil thei)nostat as it cycles
to i/iaintain ()veil tei/ll)ei'atui'e.
OVEN ® TEMP Bakingand RoastingTips
• Follow a tested recipe and nieasure the
ingredients careflflly: If you are using a
i)ackage inix, tollow lal)el directions.
• Do not open the oven door duiing
a 1)aking oi)eration--heat will be lost
and the 1)aking tiIne nlight need to
be extended. This could cause i)oor
1)aking results. If you nI list open the
dooI; open it i)artially---_mly 3 or
4 inches--and close it as quickly
as i)ossible.
• Roasting is cooking by dry heat.
Tender ineat or I)oultry can be roasted
uncovered in vour oven. Roasting
teini)eratures, which should be low
and steady, kee I) si)attering to a
nlininluin. _4]_eI1 roasting, it is not
necessai'_' h) seal; baste, cover or add
water to VO/li" illeat.
• Frozen roasts (ff beef, I)ork, lanll), etc.,
can be started without thawing, but
allow l 0 to 25 nlinutes per i)ound
additional dine (10 niinutes per pound
for roasts under 5 I)ounds, niore tiIne
for larger roasts).
• Thaw niost fl'ozen poultfy befoi'e
roasting to enstlI'e even doneness.
SoIne conlniercial fl'ozen i)oultiT
can be cooked successfiillv without
thawing. Follow directions given on
i)ackage lal)el.

Adjusttheoventhermostat--Easy todoyourself!
Youmay find that your new oven cooks differently than the one it replaced. Use your new oven for a few weeks to
become more familiar with it. If you still think your new oven is too hot or too cold, you can adjust the thermostat
yourself.
Donot use thermometers, such as those found in grocery stores, to check the temperature setting of your oven.
These thermometers may vary 20_40°F.
NOTE: This adjustment will not affect the broiling temperatures. Theadjustment will be retained after a power failure.
OVEN • TEMP
"4
Front of OVENTEMPknob
(knob appearancemay vary)
Back of OVENTEMPknob
ToAdjustthe Thermostatwith this TypeofKnob
[]
[]
Pull the OVEN TEMP knob off the range
and look at the back side.
To make an a(!jusm_ent, loosen
(al)l)ro_mately one turn), but do
not completely remove, tile two
screws on tile back ot tile knob.
With tile back of tile knob fi_cing
you, hold tile outer edge of the knob
with one hand and tm'n tile fl'ont ot
the knob with the other hand.
To increase tile oven temperatm'e,
move tile top screw toward tile right.
You'll hear a click fin" each notch wm
move the knob.
[]
[]
Each click will change tile oven
temperature approximately 10°E
(Range is l)lus or minus 60°F fl'om
tile anxm:) We suggest that w_u make
tile a(!jusm_ent one click fl'om tile
original setting and check oven
perfommnce before making any
additional a(!jusm_ents.
,liter the adjustment is made, retighten
screws so they are snug, but be
carefifl not to overtighten.
Replace the knob, matchii_g the fiat
area of the knob to the shall and
check perlommnce.
To decrease tile oven temperature,
moxe tile top screw toward tile left.
Thetypeofmargarine will affect bakingperformance!
Most recipes for baking have been
developed using high-fat products such
as butter or margarine (80% fat). If you
decrease the fat, the recipe may not
give the same results as with a higher
fat product.
Recipefailurecanresultif cakes,pies,pastries,
cookiesorcandiesaremadewithlow-fatspreads.
Thelowerthefatcontentofa spreadproduct,the
morenoticeablethesedifferencesbecome.
Federal standards require products
labeled "margarine" to contain at least
80% tilt by weight. Ixmqht spreads, on the
other hand, contain less fat and more
water: Tile high moisture content ot these
spreads affects tile texture and flavor of
baked goods. For best results with w_m" old
thvoIJte recipes, use inargaiJne, butter or
stick spreads containing at least 70%
vegetable oil.
8

Usingthe ovenforbroiling, gecom
Broiling may be slightly different from any previous broiling you maybe acquainted with, so be sure to read this
section completely.
How to Set Your Oven for Broiling
Broilingiscook/hgfoodbybtenseradiantheat
fromtheupperdementin theoven.Mostfish
andtendercutsofmeatcanbebroiiedFo/iow
thesestepstokeepspatteringandsmok/wto
8 minimum.
[] Place the shelf in l)osition Cfiw
most broiling.
Close the door. Always broil with the
door closed.
[] If the meat has tilt or gristle
around the edge, cut xertical slashes
through both about 2" apart. If
desired, tilt may be trimmed,
leaving a layer about 1/8" thick.
[] Place the meat on the broiler grid
in the broiler pan which comes with
vour range. _Mwa)'s rise the grid so
the tilt drips into the broiler pan;
otherwise the juices may become
hot enough to catch fire.
[] Turn the OVEN TEMP knob
clockwise to BROIL. You will teel
a slight niche at the broil position.
[] Turn fl_od only once dm'ing
co(>king
[] Turn the OVENTEMP knob to OFF.
Serxe fi)od immediatelx; and leave
the pan outside the oxen to cool
dm'ing the meal tot easiest cleaning.
Broiling Guide
• If desired, marinate meats or
chicken befi)re broiling, or brush
with barbecue sauce the last 5 to 10
minutes only:
• Frozen steaks can be broiled by
positioning the oven shelf at the next
lowest shelf position and increasing
cooking time given in this guide 1½
times per side.
• When arranging fl)od on pan, do not
let tiltQ' edges hang over sides because
the dripping tilt will soil the oven.
• If yore" range is cmmected to 208
voits, rare steaks may be broiled bv
lx'eheafing the broiler and positioning
the oven shelf one position higher.
Food
Bacon
GroundBeef
Beef Steaks
Medium
Chicken
Fish
Amountor
Thickness
1/2 lb.
(about8thin slices}
1 lb.(4 patties)
1/2to 3/4" thick
1" thick
1to 1VzIbs.
1whole
2to 2YzIbs.,
split lengthwise
1 lb.fillets
1/4to 1/2" thick
Shelf
Position Time In Minutes First Side Second Side
31kmira 3Vzrain.
10rain. 7mira
9 rain. 9mira
35 rain. 15rain.
5 rain. 5mira
Comments
Arrangein single laye
Spaceevenly.
Steakslessthan 1"
thickcookthrough
beforebrowning.Pan
fryingisrecommendec
Slashfat.
Reducetime about5
to 10rninutesperside
for cut-upchicken.
Brusheachsidewith
meltedbutter.Broil
skin-side-downfirst.
Handleandturnvery
carefully.Brushwith
lemonbutterbefore
andduringcooking,
if desired.Preheat
broilerto increase
browning.
9

Careand cleaningof therange.
Be sure electrical power is off and aft surfaces are cool before cleaning any part of the range.
Proper care and cleaning are important so your range will give you efficient and satisfactory service. Follow these
directions carefully in caring for your range to assure safe and proper maintenance.
If your range is removed for cleaning, servicing or any reason, be sure the anti-tip
device is reengaged properly when the range is replaced. Failure to take this
precaution could result in tipping of the range and cause injury.
Porcelain EnamelCooktop
The porcelain enamel finish is sturdy
but breakable if nlisused, This finish is
acid-resistant. However; any acidic toods
spilled (such as fruit juices, tomato or
vinegar) should not be pemfitted to
remain on the finish.
Oven Shelves
Clean the shelves with an abrasive
cleanser or steel wool. After cleaning, rinse the shelves with clean water and (hw with a clean cloth.
Receptacle
Toremove the surface unit, rift it
about I inch above the drip pan
and pull it out.
Replace the drip pan flTtothe
recess f17the cooktop.
10
Surface Units and Drip Pans
To clean the surli_ce units, mrn the
control to the highest setting fin" a
minute. The coils will burn off any soil.
Toremove a surface unit:
To remove the drip pans fi)r cleaning,
the SUlqfilceunits inust be removed first.
Make sure the SUlqfhce units are cool
heft)re touching them.
i,ifl the surlilce unit about 1 inch above
the drip pan and pull it out.
Do not lift thesurface unit more than I inch.If
you do,it maynot/ie fiat on the drippan when
youp/ug it backin.
NOTE."Repeated lifting of the surli_ce trait
more than 1 inch above the drip pan can
pemmnenfly damage the receptacle.
Toreplace a surface unit
Rel)la(e the drip pan into the recess in
the cooktop. Make sure the opening in
the pan lines up with the receptacle.
Insert the temfinals of the surti_ce unit
through the opening in the dil I) pan and
into the receptacle.
Guide the surti_ce unit into place so it
rests evenly.
Toclean the drip pans:
Drip pans can be cleaned in the
dishwasher or bv hand. If w)u use a
scouring pad, rub lightly to I)revent
scratching.
[] Can I coverthe drip pans with foil?
[] No, because using Ibil so ('lose to
the receptacle could cause shock,
fire or damage to the range.
CAUTION:
• Do not imme_e the surfi_ce traits in
liquids of any kind.
• Do not clean the surti_ce units in a
dishwasher:
• Do not bend the surlilce unit I)lug
temfinals.
• Do not attempt to clean, a(!iust or in
any way repair the plug-in receptacle.

ge.com
Lift-UpCooktop
Clean the area under the cooktopoften. Built-up
SOl'i,especla//y grease, may catch on fire.
To make cleaning easier; tile cooktop
may be lifted up and I_rol_ped open.
Be sure all smti_ce units are turned off
before raising tile cooktop.
Remove tile fl'ont smti_ce and dil I) pans.
See tile Surface Units and Dil I) Pans
section. Grasp tile two front smti_ce trait
wells and lift tile cooktop up and pro I) it
open with the prop rod provided.
_Mter cleaning underneath tile cooktop
with hot, soaI/y water and a clean cloth,
hold tile cooktop ui) ,return tile prop
rod to its storage position and lower tile
cooktop tmtil it snaps into position.
Be carefifl not to pinch yore" finge_s.
Replace the two fl'ont drip pans and
smti_ce traits. See the Stm'i_ce Units and
Drip Pans section.
HingeIoc_
Upper_/_
Ilinge_ Lower
Lift-OffOvenDoor
Tile oven door is removable, but it is
heavv. Y_m ma_, need heli ) remoxing, and
re )lacim, tile door
Toremovethe door.
[] Open tile door to tile flfll open
position.
[] Pull tile hinge locks up oxer tile
hinge hooks on both sides.
[] Grasp tile door fimfl) on each side,
lift slightly and pull it smfight out
_lll(1 _IW_IV Jl"Olll tile o_ell,
Toreplacethedoor.
[] Firefly grasp both sides oI tile door
at tile top.
[] Insert and seat tile ui)per and lower
hinge amls into the oxen slots.
[] Push the hinge locks down fl'om the
hinge hooks.
[] Close tile oxen door and make sm'e
it is working properl): If it is not
working properl> remove and
replace it fi)llowing the above steps.
DONOTATTEMPTTOCLOSETHEDOOR
UNTILTHISSTEPISCOMPLETE.THE
HINGEORDOORCOULDBEDAMAGED.
OvenHeating Elements
Do not clean tile bake element or tile
broil element. Anv soil will bm'n off when
the elements are heated.
Tile bake element can be lifted gently to
clean tile ()veil I']oor, Do not attelllpt to
clean }liiv ()veil suK]iice when }lily burner
eleinent is on. _dwavs wear protective
hand-wear when cleaning interior oven
stmfi_ces or surli_ces near heating
elements. If spillovers, residue or ash
accumulate around the bake element,
o" " (
aenfl) x_I/e ar rand the element with
wai-m watei;
Boil7the broiler pan and grid can
also becleaned in the disbwasbe_
Broiler Panand Grid
_dtei" broiling, remove tile broiler pan
fl'om tile oven. Remove tile grid fl'om tile
pan. Carefiflly pore" out grease fl'om tile
pan into a proper container _._ash and
rinse the broiler pan and grid in hot
water with a soap-filled or plastic
scorning pad.
If fi)od has bm'ned on, sprinkle tile grid
with detergent while hot and cover with
wet paper towels or a dishcloth. Soaking
tile pan will remove burned on foods.
Donotstoreasoiledbroilerpanandgrid
anywhere in the range. 11

Careand cleaningoftherange.
Control Knobs
Thecontrol knobsmaybe removedfor easier
cleaning.
Make sure tile knobs are in tile OFF
positions and pull tl/em straight off tile
stems for cleaning.
Tile knobs can be cleaned in a
dishwasher or they may also be washed
with soap and wamx: Make sure the insides
ot the knobs are (h T betore replacing.
Replace the knobs in the OFFposition
to ensure proper placement.
Painted Surfaces
Painted surfi_ces include tile sides,
control panel, door and kick panel.
Clean these with soap and water or a
vinegar and water solution.
Do not usecommercialoven cleaners,cleansing
powders,steel wool or harshabrasivesonany
painted sufface.
Porcelain Oven Interior
With propercare, theporce/albenamel interior
will retalb its attractive finish formanyyears.
Soap and water will nommllv do the job.
Hea\ T spattering or spillove_ may
require cleaning with a mild abrasive
cleanse_: Soapy, wet pads may also be
used. Do not allow tood spills with a high
sugar or add content (such as milk,
tomatoes, sauerkraut, fl'uitjuices or pie
filling) to remain on tile s/wlilce. They
may cause dull spots even after cleaning.
Household ammonia may make the
cleaning job easier. Place 1/2 cup
ammonia in a shallow glass pan and leave
in a cold oven overnight. Tile ammonia
tirades will hel I) loosen tile burned-on
grease and food.
When necessmT; pm may rise a
commercial oven cleane_: Follow the
package directions.
Cautions about using spray-on oven
c]eanersJ
• Do not spray tile oven cleaner on the
electrical controls and switches because
it could cause a short circuit and result
in sparking or fire.
• Do not directly spray oven cleaner
onto tile oven heating elements.
• Do not allow a fihn fi'om the
cleaner to remain on tile temperature
sensm_it could cause tile oven to
heat improi)edy. (Tile sensor is located
at tile top of tile oven.) Careflfllv
wipe tile bulb clean after each
oven cleaning, being carefifl not to
i/love tile sensor since a change iI1
its position could affect how tile oven
bakes.
• Do not spray any oven cleaner on tile
outside oven dora; handles or any
exterior surli_ce of tile oven, cabinet
or painted s/m'i_ces. The cleaner can
damage these s/m'i_ces.
12

! Ilnstallation 120"and24"Compact
nstructlons Electric Ranges
I[_ Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com I
BEFORE YOU BEGIN
Read these instructions completely
and carefully,
• IMPORTANT - Savethese
instructions for local inspector's use.
• IMPORTANT - Observeall
governing codes and ordinances.
•Note to Installer - Be sure to leave these
instructions with the Consumer.
•Note to Consumer - Keep these
instructions for future reference.
• Skill level - Installation of this appliance
requires basic mechanical skills.
• Completion time - 1 to 3 hours
•Proper installation is the responsibility of
the installer.
•Product failure due to improper installation
is not covered under the Warranty.
-&WARNING - This appliance must
be properly grounded.
FOR YOUR SAFETY:
_WARNING - Before beginning the
installation, switch power off at service panel
and lock the service disconnecting means to
prevent power from being switched on
accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to
the service panel.
13
FOR YOUR SAFETY:
All rough-in and spacing dimensions must be
met for safe use of your range. Electricity to
the range can be disconnected at the outlet
without moving the range if the outlet is in
the preferred location (remove lower drawer).
To reduce the risk of burns or fire when
reaching over hot surface elements, cabinet
storage space above the cooktop should be
avoided. If cabinet storage space is to be
provided above the cooktop, the risk can
be reduced by installing a range hood that
sticks out at least 5" beyond the front of the
cabinets. Cabinets installed above a cooktop
must be no deeper than 13_'
Be sure your appliance is properly installed
and grounded by a qualified technician.
Make sure the cabinets and wall coverings
around the range can withstand the temperatures
(up to 200°F) generated by the range.
ANTI-TIP DEVICE
AWARNING - Toreducetherisk
of tipping, the appliance must be secured by
properly installed Anti-Tip device packed with
this appliance.
If the Anti-Tip device supplied with the range
does not fit this application, use the universal
Anti-Tip device WB2X7909.
AWARNING-
•All ranges can tip
•Injury to persons could result
(_ •Install Anti-Tip device packed
with range
•See Installation Instructions
If you pull the range out and away from the
wall for any reason, make sure the Anti-Tip
device is engaged when the range is pushed
back against the wall.

Installation instructions
PREPARE TO INSTALL THE RANGE
MATERIALS YOU MAY NEED
(UL Approved 40 AMP)
4-Wire Cord OR 3-Wire Cord
4' Long 4' Long
Squeeze Connector
(For Conduit
Installations Only)
TOOLS YOU WILL NEED
Drill with 1/8" Bit Safety Glasses
Adjustable Wrench Tape Measure
Pliers Pencil
1/4" Nut Driver Level
Phillips Screwdriver Flat-blade
Screwdriver
PARTS INCLUDED
I
Anti-Tip Bracket Kit
_-I REMOVE SHIPPING MATERIALS
Remove packaging materials. Failure to
remove packaging materials could result
in damage to the appliance.
14
_-I PREPARE THE OPENING
• Allow 2" spacing from the range to adjacent
vertical walls above the cooktop surface. Allow
30" minimum clearance between the surface
units and the bottom of unprotected wood or
metal top cabinet, and 18" minimum between
the countertop and adjacent cabinet bottom.
• To eliminate the risk of burns or fire when
reaching over hot surface elements, cabinet
storage space above the cooktop should be
avoided. If cabinet storage space is to be
provided above the cooktop, the risk can be
reduced by installing a range hood that
protrudes at least 5" beyond the front of the
cabinets. Cabinets installed above a cooktop
may be no deeper than 13".
26" from wall
to front of
control panel From
combustible
wails above
C cooking
36"
Surface
Wall Mounted ,-.......
outlet
Wall
Floor
Recorrlrnended acceptable electrical outlet
area. Orient the electrical receptacle so
the length is parallel to the floor.
with door
open)
Flooring under the range
Your range, like many other household items,
is heaw and can settle into soft floor coverings
such as cushioned vinyl or carpeting.
When moving the range on this type of
flooring, it should be installed on a 1/4"
thick sheet of plywood (or similar material)
as follows:
When the floor covering ends at the front
of the range, the area that the range will
rest on should be built up with plywood
to the same level or higher than the floor
covering. This will allow the range to be
moved for cleaning or servicing.
C
Models AB recommended) D
20" Wide 20" 20%" 2" 41"
24" Wide 24" 243/8" 2" 41"

Installation instructions
ELECTRICAL CONNECTIONS
ELECTRICAL REQUIREMENTS
ACAUTION: For personal safety,
do not use an extension cord with this
appliance. Remove house fuse or open circuit
breaker before beginning installation.
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as specified on the rating
plate. The rating plate is located under the
cooktop. See the Lift-Up Cooktop section
in this manual for instructions on how to
lift the cooktop.
Rating Plate
We recommend you have the electrical wiring
and hookup of your range connected by a
qualified electrician. After installation, have
the electrician show you where your main
range disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to
wire your oven according to governing codes
could result in a hazardous condition. If there
are no local codes, your range must be wired
and fused to meet the requirements of the
National Electrical Code, ANSI/NFPA No. 70-
Latest Edition. You can get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new construction
(not existing) utilize a 4-conductor connection
to an electric range.
ELECTRICAL REQUIREMENTS (cont.)
When installing an electric range in new
construction, follow Steps 3 and 5 for 4-wire
connection.
You must use a 3-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors
approved for use with aluminum wiring
must be used.
If the electrical service provided does not
meet the above specifications, have a
licensed electrician install an approved outlet.
ALL NEW BRANCH CIRCUIT
INSTALLATIONS, MOBILE
HOMES, RECREATIONAL
VEHICLES AND
INSTALLATIONS WHERE
LOCAL CODES DO NOT
ALLOW GROUNDING
THROUGH NEUTRAL,
REQUIRE A 4-CONDUCTOR
CORD OR CONDUIT
Use only a 3-conductor or a 4-conductor
UL-listed range cord. These cords may be
provided with ring terminals on wire and
a strain relief device.
A range cord rated at 40 amps with 125/250
minimum volt range is required. A 50 amp
range cord is not recommended but if used, it
should be marked for use with nominal 13/_"
diameter connection openings. Care should
be taken to center the cable and strain relief
within the knockout hole to keep the edge
from damaging the cable.
• Because range terminals are not accessible
after range is in position, flexible service
conduit or cord must be used.
NOTE: If conduit is being used, go to Step 3D
and then to Step 6 or 7.
• On some models, a filter capacitor may be
connected between the black and white
leads on the junction block.
15

Installation instructions
ELECTRICAL CONNECTIONS (CONT.)
[] POWER CORD AND STRAIN
RELIEF INSTALLATION
[]
[]
Remove the wire cover (on the lower
back of the range) by removing its top
center screw,
Do not discard this screw.
Remove the knockout ring (13/8'') located
on bracket directly below the terminal
block. To remove the knockout, use a
pair of pliers to bend the knockout ring
away from the bracket and twist until
ring is removed.
_j erminal block
(appearance
may vary)
Knockout ring
in bracket
Knockout
ring removed
[] For power cord installations only (see
the next step if using conduit), assemble
the strain relief in the hole. Insert the
power cord through the strain relief and
tighten. Allow enough slack to easily
attach the cord terminals to the terminal
block. If tabs are present at the end of
the winged strain relief, they can be
removed for better fit.
NOTE: Do not install the power cord
without a strain relief. The strain relief
bracket should be installed before
reinstalling the rear range wiring cover.
Terminal
block
Strain relief
Power cord
Skip to Step 4 or 5.
Bracket
16
[] For conduit installations only, purchase a
squeeze connector matching the diameter
of your conduit and assemble it in the hole.
Insert the conduit through the squeeze
connector and tighten. Allow enough slack to
easily attach the wires to the terminal block.
NOTE: Do not install the conduit without a
squeeze connector. The squeeze connector
should be installed before reinstalling the
rear range wiring cover.
Terminal
block
Squeeze
connector
Conduit
Skip to Step 6 or 7.
\
Bracket

Installation instructions
[]
3-WIRE POWER CORD
INSTALLATION
WARNING: The neutral or ground
wire of the power cord must be connected
to the neutral terminal located in the
center of the terminal block. The power
leads must be connected to the lower left
and the lower right terminals of the
terminal block.
Remove the 3 lower terminal screws
from the terminal block. Insert the 3
terminal screws through each power cord
terminal ring and into the lower terminals
of the terminal block. Be certain that the
center wire (white/neutral) is connected
to the center lower position of the
terminal block. Tighten screws securely
into the terminal block.
DO NOT remove the ground strap
connection.
Ground plate
///
Power ci__
Terminal
block
\ _ (appearance
_ may vary)
_ Neutral
' ].V terminal
_ round
strap
©
[] Skip to Step 8 and proceed with the
installation.
17
[] 4-WIRE POWER CORD
iNSTALLATiON
WARNING: TheneutraIwireof
the supply circuit must be connected to the
neutral terminal located in the lower center
of the terminal block. The power leads must
be connected to the lower left and the lower
right terminals of the terminal block. The 4th
grounding lead must be connected to the
frame of the range with the ground plate
and the ground screw.
[] Remove the 3 lower terminal screws from
the terminal block. Remove the ground
screw and ground plate and retain them.
[] Cut and discard the ground strap. DO NOT
DISCARD ANY SCREWS.
[] insert the one ground screw into the power
cord ground wire terminal ring, through the
ground plate and into the frame of the range.
[] insert the 3 terminal screws (removed earlier)
through each power cord terminal ring and
into the lower terminals of the terminal block.
Be certain that the center wire (white/neutral)
is connected to the center lower position of
the terminal block. Tighten screws securely
into the terminal block. Ground strap
tChUt_o_udni_°_ _2ut_;i
After Neutral
terminal
Terminal
block
Ground
screw
Ground
plate
(grounding
to range)
\
%
[] Skip to Step 8 and proceed with the installation.

Installation Instructions
ELECTRICAL CONNECTIONS (CONT.)
3-WIRE CONDUIT INSTALLATION
Loosen the 3 lower terminal screws from
the terminal block. Insert the center bare
wire (white/neutral) tip through the bottom
center terminal block opening. On certain
models, the wire will need to be inserted
through the ground strap opening and then
into the bottom center block opening. Insert
the two side bare wire tips into the lower
left and the lower right terminal block
openings. Tighten the screws until the wire
is firmly secure (approximately 20 inch-lbs.),
NOTE: ALUMINUM WIRING:
Aluminum building wire may be used
but it must be rated for the correct
amperage and voltage to make
connection. Connect wires according
to this Step 6 or Step 7 depending on
number of wires.
Terminal
block
Wire tips
Bracket Conduit
Wire used, location and enclosure
of splices, etc., must conform to good
wiring practices and local codes.
[] Skip to Step 8 and proceed with the
installation.
[-_ 4-WIRE CONDUIT INSTALLATION
[]
[]
Loosen the three lower terminal screws
from the terminal block. Remove the ground
screw and ground plate and retain them.
Cut and discard the ground strap. DO NOT
DISCARD ANY SCREWS.
Insert the ground bare wire tip between the
range frame and the ground plate (removed
earlier) and secure it in place with the ground
screw (removed earlier), Insert the bare wire
(white/neutral) tip through the bottom center
of the terminal block opening. Insert the two
side bare wire tips into the lower left and the
lower right terminal block openings. Tighten
the screws until the wire is firmly secure
(approximately 20 inch-lbs.).
Before _/____ Greed strap
Terminal_blOCkcutand discard J_'_Y_*_L__S:_I_tJ_ _ or
the ground strap Neutral ter_"minal
After _/_
Terminal //__r_t_
block /(__'_ t__1_ Ground
Wire tips _j_ _gat_ riding
Gcr°Un d-----'___B rac ket
[]
Wire used, location and enclosure
of splices, etc., must conform to good
wiring practices and local codes.
Proceed to Step 8.
18
[-_ REPLACE THE WIRE COVER
Replace the wire cover on the range back
by sliding its two lower retaining tabs into
the slots and replacing the screw removed
earlier. Make sure that no wires are pinched
between the cover and the range back.

Installation Instructions
INSTALL THE RANGE
[] ANTI-TIP DEVICE INSTALLATION
.4,WARNING:
* Range must be secured with an
approved Anti-Tip device.
• Unless properly installed, the range could
be tipped by you or a child standing, sitting
or leaning on an open door.
• After installing the Anti-Tip device, verify
that it is in place by carefully attempting
to tilt the range forward.
• This range has been designed to meet all
recognized industry tip standards for all
normal conditions.
• After installing the Anti-Tip device, verify
that it is in place by carefully attempting
to tilt the range forward.
• The use of this device does not preclude
tipping of the range when not properly
installed.
[] Mark the wall where the RIGHT EDGE of
the range is to be located. Be sure to allow
for the countertop overhang if you intend
to install the range next to cabinets.
[] Locate the
outside edge
of the device head
21_" toward screw
the center of Appro)
the range
from the Marked
marked edge _dge
of the range.
[] Using the device as a template, mark the
position of the hole for the screw.
[] For wood construction, drill a pilot hole at
an angle of 20 degrees from the horizontal.
A nail or awl may be used if a drill is not
available.
Mount the Anti-Tip device with the screw provided.
For cement or concrete construction, you will
need a 1/4" x 11/21z Wallboard Back of
lag bolt and a
1/2" O.D. sleeve range
anchor, which
are not provided.
Drill the
recommended Woodscrew
size hole for the
hardware.
19
ANTI-TIP DEVICE INSTALLATION
(cont.)
[]
Install the sleeve anchor into the drilled hole
and then install the lag bolt through the
device. The bolts must be properly tightened
as recommended for the hardware.
Slide the range against the wall, and check
for proper installation by grasping the front
edge of the cooktop and carefully
attempting to tilt the range forward.
[]
[]
LEVEL THE RANGE
For proper cooking and baking, the range
must be leveled. Leveling legs are located
on each corner at the base of the range.
Install the oven shelves
(see Using the oven
section for instructions).
Put a spirit level or a glass
measuring cup partially
filled with water on one
of the oven shelves.
Turn the legs clockwise
to raise the range and
counterclockwise to
lower the range. Adjust
the leveling legs until
the range is level.
FINAL INSTALLATION CHECKLIST
Check to make sure the circuit breaker is closed
(RESET) or the circuit fuses are replaced.
Be sure power is in service to the building.
Check to be sure that all packing materials
and tape have been removed. This will
include tape on metal panel under control
knobs (if applicable), adhesive tape, wire
ties, cardboard and protective plastic. Failure
to remove these materials could result in
damage to the appliance once the appliance
has been turned on and surfaces have heated.
• Check to make sure that the Anti-Tip device
is securely installed.
• Be sure all range controls are in the OFF
position before leaving the range.

Before YouCall ForService...
TrOubleshooting -tips
Save time and money! Review the chart on this page
t and you may not need to call for service.
Problem Possible Causes What To Do
Surface un#s not The surface milts are *_._]th tile controls off, check to make sure tile surtil('e
functioning properly not plugged hasolidly, unit is plugged completely into tile receptacle.
The surface refit controls *Check to see the correct control is set fl)r the stmfi_ce
improperly set. unit xou are usin,
The drip pans are not set • _]th tile controls off, check to make sure tile drip
securely in the cooktop, pan is in tile recess in tile cooktop and that tile
opening in tile pan lines up with tile receptacle.
Ovenwill A fuse in your home may •Replace tile fllse or reset tile drcuit breaker.
not Work be blown or the circuit
breaker tripped.
Plug on range is not • Make sure electrical plug is plugged into a live, properly
completely inserted in grounded outlet.
the electrical outlet.
Oven control • See tile Using the oven sections.
improperly set.
Food does not Oven control * Make stu'e veil ttlrn tile knob all tile way to tile
broilproperly hnproperly set. BROIL position.
Improper shelf position • See tile Broiling Guide.
being used.
Cookware not suited * Use tile broiling pan and grid that came with your range.
for broiling.
Aluminum foil used on the * See tile Use of aluminum foil section.
the broiling pan and grid has
not been fitted properly and
slit as recommended.
Fooddoes not bake Oven control *See tile Using the oven for baking or roasting section.
or roastproperly improperly set.
Shelf position is incorrect *See tile Using the oven for baking or roasting section.
or the shelf is not level.
Necessary preheating * See the Using the oven for baking or roasting section.
was not done.
•See tile Using the oven forbaking orroasting section.
Incorrect cookwaxe or
cookwaace of improper
size being used.
2O