Housnat CM5418-UL User manual

MODEL:CM5418-UL
INSTRUCTION MANUAL
Please read these instructions carefully and retain for future reference.

IMPORTANT
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
The following basic safety rules should always be followed:
Make sure that your outlet voltage match the voltage that stated on the
product.
This appliance has been incorporated with a grounded plug. Please
ensure the wall outlet in your house is earthed.
To prevent fire, electric shock or injury to users do not immerse cord or
plug into water or other liquid.
Unplug the product if not in use or ready to clean. Let the espresso
machine come to room temperature before clean or assemble.
Do not use the machine if the cord or plug is damaged, or the machine
is broken. Return or replace the product to the retailer.
Do not use the accessories that is not provided by the manufacturer, it
may result in fire, electric shock or injury to persons.
To avoid inadvertently pulling the cord, put the machine on a level
surface or table. Don't hang the cord over the edge of the table or
counter.
Do not let the power cord touch or be too close to the hot object.
Do not place the product near any hot objects, such as: gas stove,
electric burner, or heated oven.
Unplug the appliance only after switching off and only pull the plug not
the cord.
Do not use appliance for unconventional purposes.
Closely monitored if the product is used by children or near by children.
Be careful not to get burned by the steam.
Some parts of appliance are boiling hot while operating (such as the
steam wand and the steel portafilter). So do not touch it with hand. Use
handles or knobs instead.
Do not operate the coffee maker without water.
To avoid scalding, do not remove the water tank during the brewing
process.
Do not remove the portafilter when the machine is brewing or steaming.
Ensure to release the pressure before removing the portafilter.
Connect the plug to the wall outlet before using. Switch off the machine
before removing the plug from the wall outlet.
Relief pressure through steam wand before removing water tank or
portafilter.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experi-
ence and knowledge unless they have been given supervision or
instruction concerning the use of the appliances by a person responsi-
ble for their safety.
Do not use the espresso machine outdoors.
01 02 03 04 05 06 07 08 09
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49

The following basic safety rules should always be followed:
Make sure that your outlet voltage match the voltage that stated on the
product.
This appliance has been incorporated with a grounded plug. Please
ensure the wall outlet in your house is earthed.
To prevent fire, electric shock or injury to users do not immerse cord or
plug into water or other liquid.
Unplug the product if not in use or ready to clean. Let the espresso
machine come to room temperature before clean or assemble.
Do not use the machine if the cord or plug is damaged, or the machine
is broken. Return or replace the product to the retailer.
Do not use the accessories that is not provided by the manufacturer, it
may result in fire, electric shock or injury to persons.
To avoid inadvertently pulling the cord, put the machine on a level
surface or table. Don't hang the cord over the edge of the table or
counter.
Do not let the power cord touch or be too close to the hot object.
Do not place the product near any hot objects, such as: gas stove,
electric burner, or heated oven.
Unplug the appliance only after switching off and only pull the plug not
the cord.
Do not use appliance for unconventional purposes.
Closely monitored if the product is used by children or near by children.
Be careful not to get burned by the steam.
Some parts of appliance are boiling hot while operating (such as the
steam wand and the steel portafilter). So do not touch it with hand. Use
handles or knobs instead.
Do not operate the coffee maker without water.
To avoid scalding, do not remove the water tank during the brewing
process.
Do not remove the portafilter when the machine is brewing or steaming.
Ensure to release the pressure before removing the portafilter.
Connect the plug to the wall outlet before using. Switch off the machine
before removing the plug from the wall outlet.
Relief pressure through steam wand before removing water tank or
portafilter.
●
●
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experi-
ence and knowledge unless they have been given supervision or
instruction concerning the use of the appliances by a person responsi-
ble for their safety.
Do not use the espresso machine outdoors.
KNOW YOUR COFFEE MAKER
1.
2.
3.
4.
5.
6.
7.
8.
NOTES ON THE CORD PLUG
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
This appliance has a polarized plug, To reduce the risk of electric shock, this
plug is intended to fit into a polarized outlet only one way, If the plug does
not fit fully into the outlet, reverse the plug, If it still does not fit, contact a
qualified electrician, Do not attempt to modify the plug in any way.
NOTES ON THE CORD
a) A short power-supply cord (or detached power-supply cord) is to be
provided to reduce risks resulting from becoming entangled in or tripping
over a long cord.
b) Longer detachable power-supply cords or extension cords are available
and may be used if care is exercised in their use.
c) If a long detachable power-supply cords or extension cord is used,
1) The marked electrical rating of the detachable power-supply cord or
extension cord should be at least as great as the electrical rating of the
appliance.
2) If the appliance if of the grounded type, the extension cord should be a
grounding-type 3-wire cord,
3) The longer cord should be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children or tripped
over.
Power indicator/button
Single-cup indicator/button
Double-cup indicator/button
Steam indicator/button
Brewing filter
Metal funnel
Funnel handle
Drip plate
9.
10.
11.
12.
13.
14.
15.
16.
Drip tray
Tank cover
Handle
Water tank
Knob
Steam handle
Steam wand
Measuring spoon
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
01 02 03 04 05 06 07 08 09
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49

Turn the portafilter clockwise to remove it, add coffee powder to the filter
with the measuring spoon (a spoon of coffee powder can make about a
single shot of espresso), then compress the coffee powder into a dense.
Set filter into the portafilter, then insert the portafilter into the appliance
from the “LOCK” position, and turn it anticlockwise until it is at the
“CLOSE”position.
Place a cup on the drip plate.
Select single cup “ ” or double-cup “ ” according to your
demand. After waiting for a moment, espresso will flow out.
The appliance will automatic stop flow After dispensing the right amount
of espresso. The espresso is ready to serve.
After making the espresso, remove the portafilter and pour out the used
coffee powder.
MAKE ESPRESSO COFFEE
1.
2.
3.
4.
5.
6.
Press the steam button “ ”, the indicator will flash while preheating.
When the indicator stops flashing, the preheating is finished.
Fill a milk frothing pitcher with 100 grams of milk, it is recommended to
use cold whole milk for making milk foam.
Pitcher Size: It is recommended that the diameter is not less than
70±5mm, the volume of milk will increase by 2 times after frothing, make
sure the picher is high enough.
Put the steam wand into the milk to a depth of about 2 cm, then turn the
knob to the “ ” position, steam will be release from the steam wand.
Move the milk frothing pitcher up and down to froth milk. Turn the knob
off when you get enough milk foam.
FROTHING MILK/MAKE HOT WATER
1.
2.
3.
Press the double-cup button “ ” the indicator will flash while
preheating. When the indicator stops flashing, the preheating is finished.
Turn the knob to “ ” position, the hot water will dispense from the
steam wand. Turn the knob off when you get enough hot water.
1.
2.
3.
4.
5.
6.
7.
Remove the plug at the bottom of the water tank.
Pour water into the water tank, the water level should not exceed the
maximum level in the water tank. Then close the lid.
Note: The water tank is removable and easy to clean. You can fill the
water tank with water first, and then put the water tank on the appliance.
Set filter into the portafilter, do not add coffee powder. Then insert the
portafilter into the appliance from the “LOCK” position, and turn it
anticlockwise until it is at the “CLOSE” position.
Place a cup on the drip plate. Make sure the knob is in the horizontal
position(off-position).
Note: the appliance is not equipped with cup.
Connect the plug, press the power button “ ”. The power indicator will
light on and the single-cup/double-cup/steam indicator will flash. The
appliance start preheating.
When the single-cup/double-cup/steam indicator stops flashing, the
preheating is finished. Press the double-cup button “ ”, wait for a
moment, the water will flow out.
When the appliance stops pumping water, repeat step 6 several time
until the clean water flow out, now you can start brewing.
Note: It is normal that there may be noise during the first pumping.
Beacuse the appliance is releasing air inside the machine. After about
20s, noise will reduce.
CLEANING MACHINE/PRE-HEATING
To ensure the coffee tastes excellent, you should clean the espresso
machine before the first use.
It is recommended to preheat the appliance before making espresso,
including the portafilter, filter and cup, so that the coffee flavor will not be
affected by temperature.
01 02 03 04 05 06 07 08 09
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49

Set the output of single-cup
Press the “Single-cup” button for 3 seconds to start the setting mode.
Then press the “Single-cup” button again, the espresso starts to
dispense and the “Single-cup” indicator flashes at the same time, when
you get enough espresso, press the “Single-cup” button again, the
espresso stops flowing down. At that time, the setting amount of
single-cup is finished and it will be saved for the next operation. The
dispensing amount for a single cup is ranged from 25ml to 60ml.
Set the output of double-cup
Press the “Double-cup” button for 3 seconds to start the setting mode,
then follow the setting process of single-cup. The dispensing amount for
double-cup is ranged from 70ml to 110ml.
Restore default setting
Press the “Single-cup” and “Double-cup” buttons for 3 seconds simulta-
neously to restore the default setting.
SET THE AMOUNT OF OUTPUT
1.
2.
3.
After pressing the power button, if there is no operation within 29
minutes, the unit will power off automatically.
Steam function: Press the steam button “ ”, turn the knob to the “ ”
position. if there is no operation after 180s, the steam function will stop
automatically.
Hot water function: Press the steam button “ ”, turn the knob to “ ”
position. if there is no operation after dispensing about 215ml water, the
hot water function will stop automatically.
AUTOMATICALLY POWER-OFF
1.
2.
3.
Press the steam button “ ”, the indicator will flash while preheating.
When the indicator stops flashing, the preheating is finished.
Fill a milk frothing pitcher with 100 grams of milk, it is recommended to
use cold whole milk for making milk foam.
Pitcher Size: It is recommended that the diameter is not less than
70±5mm, the volume of milk will increase by 2 times after frothing, make
sure the picher is high enough.
Put the steam wand into the milk to a depth of about 2 cm, then turn the
knob to the “ ” position, steam will be release from the steam wand.
Move the milk frothing pitcher up and down to froth milk. Turn the knob
off when you get enough milk foam.
4. Press the double-cup button “ ” the indicator will flash while
preheating. When the indicator stops flashing, the preheating is finished.
Turn the knob to “ ” position, the hot water will dispense from the
steam wand. Turn the knob off when you get enough hot water.
1.
2.
3.
4.
5.
The steam wand can only be used to froth milk or make hot chocolate.
While using the steam wand, the portafilter must be assembled in the
right position.
Before frothing milk, release the steam for 10 seconds.
The steam wand are hot while operating, so do not touch it with hand.
Clean the steam wand with a wet cloth immediately after frothing milk.
After making steam, you can press the "Single-cup” or “Double-cup” button
immediately to make espresso again. The indicator will flash if the
temperature is too high.
At this time, you need to turn the knob to the "Hot water” setting “ ”,
then the hot water will dispense to reduce the temperature. When the
temperature goes down, you should turn the knob off, and then you can
make espresso again.
If you do not want to make espresso when the high-temperature warning
occurs, you can press the “Single-cup” or “Double-cup” button again to
cancel it.
Note:
01 02 03 04 05 06 07 08 09
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49

Turn the knob to “ ”
position and start cooling
operation.
Shut off the power and let the espresso machine cool down completely.
Clean the espresso machine, water tank, drip tray, and drip plate with a
sponge and dry them after each use.
Note: Do not clean with alcohol or solvent cleaner. Never immerse the
whole espresso machine into water for cleaning.
Turn the portafilter clockwise to remove it, pour out the coffee powder,
then clean the portafilter with cleanser and rinse it with water.
Note: The portafilter is not dishwasher safe, do not clean it in the
dishwasher.
Clean all the attachments and dry them.
CLEAN AND MAINTENANCE TROUBLESHOOTING
1.
2.
3.
4.
After the appliance has cumulatively worked for 500 cycles, it will trigger
descaling warning that all indicators will flash for 5 times. At this time the
espresso machine needs to be descaled, after descaling the indicators
will back normal.it will continuously trigger descaling warning if you do
not cancel it.
Fill the water tank with water and descaler to the MAX level, please use
“coffee machine descaler”, the ratio of water and descaler should base
on the instruction of descaler. You can use the citric acid instead of the
descaler (the one hundred parts of water and three parts of citric acid).
Press the "Double-cup” button once to dispense hot water for about
100ml. Then turn off the appliance and leave the descaling solution in
the appliance for 5 minutes.
Turn on the appliance and repeat step 3 three times.
Repeat step 3 twice with tab water (it is not necessary to wait for 5 minutes).
After descaling, you need to cancel the descaling warning by press and
hold the “Single-cup” button“Double-cup” button and “steam” button
for 3 seconds simultaneously.
Water leaks from
the bottom of the
espresso
machine.
There is too much water in the drip tray. Please clean the drip tray.
CLEAN LIMESCALE
1.
2.
3.
4.
5.
6.
Symptom Cause Solutions
Water leaks out of the
outer side of the filter.
There is some coffee powder on the
filter edge.
Wip out the coffee powder
on the edge.
Acid (vinegar)
taste exists in
Espresso coffee.
Not cleaned properly after use. Clean the machine several
times before use.
The espresso
machine is not
working.
The espresso machine is not
plugged well.
Plug the power cord into
the socket correctly.
The milk
cannot be
frothed.
The indicator is not on. Only after the indicator is on, the
steam can be used to froth milk.
Single-cup indicator
and double-cup
indicator flash quickly.
Dispense hot water for more than
215ml and the knob is not turned off.
Turn the knob off.
Steam indicator
flash quickly.
Make steam for more than 180s
and the knob is not turned off.
Turn the knob off.
ALL indicator flash at
the same time for 5
times
Need descaling
Do not take apart the appliance by yourself if the cause of a malfunction is not found,
you had better contact Amazon seller.
Refer to “CLEAN LIMES-
CALE”
Single-cup indicator
or double-cup
indicator flash quickly.
Bolier temperature is getting too high.
Turn the knob to “OFF”
position.
Single-cup indicator,
double-cup indicator
and steam indicator
flash quickly.
The machine is on but the knob is not
turn off.
The coffee powder is stored in
a hot or wet place for a long
time. The coffee powder turns
bad.
Please use fresh coffee
powder, sealed and stored
the coffee powder in a cool
and dry place.
The espresso machine is
malfunctioning.
Please contact Amazon
seller for replacement.
The container is too big or the
shape is not suitable.
Use professional milk
frothing pitcher.
The knob is not reset after cooling down.
Use Skimmed milk or plant milk. Use whole milk (butterfat>3%)
The water pipe inside the machine is
damaged.
Please contact Amazon
seller for replacement.
01 02 03 04 05 06 07 08 09
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49