HP StorageWorks FC4-16 User manual

HP StorageWorks
4Gb SAN Director Port Blade
installation instructions
© Copyright 2006 Hewlett-Packard Development Company, L.P.
First edition (November 2006)
Product names mentioned herein may be trademarks of their
respective companies as reflected by an associated footnote.
The information in this document is subject to change without
notice.
Printed in the US
www.hp.com
*A7990-90003*
Overview
Read these instructions to install the following optional 4Gb SAN
Director Port Blades:
•HP StorageWorks 16 Port 4Gb Blade (FC4–16),
Part Number A7990A, installs in the HP StorageWorks
SAN Director 2/128 or HP StorageWorks 4/256 SAN Director
models
only
•HP StorageWorks 32 Port 4Gb Blade (FC4–32),
Part Number A7991A, installs in the HP StorageWorks
4/256 SAN Director model
only
•HP StorageWorks 4/48 SAN Director Blade (FC4–48),
Part Number AG561A, installs in the the HP StorageWorks 4/256
SAN Director model
only
NOTE:
For simplicity, the port blades are referred to as FC4–16,
FC4–32 and FC4–48 throughout this document.
Refer to the HP StorageWorks SAN Director installation guide for a
complete list of 4Gb SAN Director Port Blade technical specifications.
Intended audience
These installation instructions are intended for use by system technicians
who are experienced with:
•Setting up devices in a SAN
•HP StorageWorks Fibre Channel Directors
Relateddocumentation
For the latest information, documentation, and firmware releases, please
visit the following HP StorageWorks web site:
http://www.hp.com/country/us/eng/prodserv/storage.html
Compatibility
Refer to Table 1 to determine which SAN Director models are
compatible with your specific 4Gb SAN Director Port Blade.
IMPORTANT:
Install 4Gb Port Blades in the SAN Director models listed only.
Table 1 4Gb SAN Director Port Blade compatibility
4/16 SAN
Director Port
Blade (FC4-16)
4/32 SAN
Director
Port Blade
(FC4–32)
4/48 SAN
Director
Port Blade
(FC4–48)
SAN Director
2/128 Compatible Not compatible
Not
compatible
4/256 SAN
Director
Compatible Compatible Compatible
NOTE:
Installation procedures for the B-Series Multi-protocol Router
Blade are not included in this document. Please refer to
the
HP StorageWorks B-Series Multi-protocol Router Blade
installation guide
available via the link provided above in
Related documentation.
Page 1

Chassis configuration setting
When migrating a SAN Director with two domains (two logical
switches) to a 4/256 SAN Director, the result will be a SAN Director
with only one domain. Depending on your configuration, this
may change the topology of the fabric and should be taken into
consideration when planning your installation.
The 4/256 SAN Director supports chassis configuration options 1 or
5only. UsethechassisConfig command to change the chassis
configuration. The valid options are:
•Option 1 — One (up to) 128-port logical switch. This chassis mode
supports CP4 control processor blades managing FC4–16.
•Option 5 — One (up to) 384-port logical switch. This chassis mode
supports CP4 control processor blades managing the FC4–16,
FC4–32, and FC4–48.
Blade components and port numbering
The following sections illustrate 4Gb SAN Director Port Blade
components.
FC4–16 Port Blade components
Figure 1 identifies FC4–16 blade components and the port numbering
scheme. Ports are numbered from 0 through 15 from bottom to top.
15
14
13
12
11
10
56-0000590-01 Rev A
!
7
6
5
4
3
2
1
0
15
14
13
12
11
10
9
8
56-0000590-01 Rev A
!
FC4
16
1
2
3
4
5
6
7
8
25027a
Figure 1 FC4–16 components
Callouts
1. On/Off switch (On position) 5. Port speed LED
2. Power LED 6. Port status LED
3. Status LED 7. Thumb screw
4. Fibre Channel port 8. Ejector
FC4–32 and FC4–48 Port Blade components
Figure 2 identifies FC4–32 and FC4–48 blade components and port
numbering schemes.
For the FC4–32, ports are numbered from 0 through 15 from bottom to
top on the left set of ports, and 16 through 31 from bottom to top on
the right set of ports.
For the FC4–48, ports are numbered from 0 through 23 from bottom to
topontheleftsetofportsand24through47frombottomtotopon
the right set of ports.
24
0
25
1
26
2
27
3
28
4
29
5
30
6
31
7
32
8
33
9
34
10
35
11
36
12
37
13
38
14
39
15
40
16
41
17
42
18
43
19
44
20
45
21
46
22
47
23
!
44
20
45
21
46
22
47
23
!
31
15
30
14
29
13
28
12
27
11
26
10
25
9
24
8
23
7
22
6
21
5
20
4
19
3
18
2
17
1
16
0
!
FC4
32
!
31
15
30
29
27
14
13
28
12
1
25225a
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Figure 2 FC4–48 (left) and FC4–32 (right) components
Callouts
1. On/Off switch (on position) 10. On/Off Switch (Off position)
2. FC4–48 power LED 11. FC4–32 power LED
3. FC4–48 Fibre Channel ports 12. FC4–32 status LED
4. Thumb screw 13. FC4–32 port speed LED
5. FC4–48 status LED 14. FC4–32 port status LED
6. FC4–48 port status LED 15. Port speed LED for FC4–32
(for FC4–32 this LED indicates
the port speed for the left port)
7. Port status LED for FC4-32
and FC4-48 (for FC4–32 and
FC4–48, this LED indicates the
port status for the left port)
16. Port status LED for FC4–32
and FC4–48 (for FC4–32 and
FC4–48, this LED indicates the
port status for the left port)
8. Thumb screw 17. Fibre Channel port
9. Ejector
Page 2

Time and items required for install
The installation takes less than 10 minutes. Obtain the following items:
•4Gb SAN Director Port Blade
•Minimum of two Power Supplies installed in the SAN Director
•Electrostatic Discharge (ESD) grounding strap
•Replacement filler panel for each empty slot (ships with the SAN
Director)
•Workstation computer
•Phillips screw driver
•SFP transceiversandopticalcables(asneeded)
Remove the filler panel
Remove the filler panel, if installed. There are three filler panel types,
see Figure 3:
POWER SUPPL
Y 1
200-240 VAC 12A 50-60 Hz 200-240 VAC 12A 50-60 Hz
POWER SUPPL
Y 1
!
!
POWER SUPPL
Y 2
!
!
POWER SUPPL
Y 3
POWER SUPPL
Y 4
!
!
7
6
5
4
3
2
1
0
15
14
13
12
11
10
9
8
56-0000590-01RevA
!
FC4
16
CP4
Link
10/100Mb/s
ActiveCP
!
I O I O IRS - 232
CP4
Link
10/100Mb/s
ActiveCP
!
I O I O IRS - 232
7
6
5
4
3
2
1
0
15
14
13
12
11
10
9
8
56-0000590-01RevA
!
FC4
16
12345678910
7
25043a
65
4
3
2
1
Figure 3 Removing three different filler panel types
Callouts
1. Filler panel with handle 5. Ejectors (2)
2. Captive screws (2) 6. Pull tabs (2)
3. Handle 7. Filler panel with pull tabs
4. Filler panel with ejectors
1. To remove a filler panel with a handle:
a. Unscrew the two captive screws securing the filler panel.
b. Grasp the handle in the middle of the filler panel and remove.
2. To remove a filler panel with ejectors:
a. Push in the yellow tab on each ejector.
b. Lever both ejectors all the way open, and remove the filler
panel from the chassis.
3. To remove a filler panel with pull tabs:
a. Unscrew the top and bottom captive screws on the filler panel.
b. Pull on the top and bottom pulling tabs to slide the filler panel
out of the chassis.
IMPORTANT:
Remove a filler panel only when installing a port blade. Any
slot that is not occupied by a port blade requires a filler panel to
ensure correct cooling of the chassis and protection from dust.
Installing the port blade
The FC4–16 and FC4–32 port blades use the same procedure.
However, the FC4–48 differs slightly in design. Port blade-specific
instructions are called out where applicable, as follows:
CAUTION:
Wear a grounded ESD strap when handling the port blade.
The 4/256 SAN Director chassis has a grounding connection
above the power connectors.
1. Locate an appropriate slot. Install port blades in slots 1 through 4;
and 7 through 10.
NOTE:
For details on supported mixed blade configurations, refer to
the
HP StorageWorks SAN Director installation guide .
2. Orient the port blade so that the ports are at the front of the chassis
and the flat side of the port blade is on the left, see Figure 4.Hold
the port blade by the edges of the metal pan. Do not use the
ejectors to hold the port blade.
CAUTION:
Make sure to gently apply pressure to the port blade, in order
to properly seat the card all the way into the slot. Applying
excessive pressure may damage the VHDM connectors on the
Director’s backplane.
POWER SUPPLY 1
200-240 VAC 12A 50-60 Hz 200 -240 VAC 12A 50-60 Hz
POWER SUPPLY 1
!
!
POWER SUPPLY 2
!
!
POWER SUPPLY 3
!
!
POWER SUPPLY 4
!
!
!
!
FC4
32
FC4
32
7
6
5
4
3
2
1
0
1
5
1
4
1
3
1
2
1
1
10
9
8
56-0000590-01RevA
!
FC4
16
CP4
Link
10/100Mb/s
ActiveCP
!
I O I O IRS - 232
CP4
Link
10/100Mb/s
ActiveCP
!
I O I O IRS - 232
7
6
5
4
3
2
1
0
1
5
1
4
1
3
1
2
1
1
10
9
8
56-0000590-01RevA
!
FC4
16
12345678910
7
6
5
4
3
2
1
0
1
5
1
4
1
3
1
2
1
1
10
9
8
56-0000590-01RevA
!
FC4
16
3
1
2
4
25217a
Figure 4 Installing a FC4–16 or FC4–32 Port Blade
Callouts
1. SAN Director chassis 3. On/Off slider switch
2. FC4-16 4. Ejector
Page 3

3. If installing theFC4–48,gotostep4.
For FC4–16 and FC4–32 models (see Figure 4).
a. Open the ejectors to approximately 45 degrees.
b. Align the flat side of the port blade inside the upper and lower
rail guides in the slot, and slide the port blade into the slot,
with slight pressure to the left, until it is firmly seated.
4. For FC4–48 models (see Figure 5):
a. Adjust the ejectors to the open position.
b. Align the flat side of the port blade inside the upper and lower
rail guides in the slot.
c. Slide the port blade into the slot, until it is firmly seated.
POWER SUPPL
Y 1
200-24 0 VAC 12 A 50-60 Hz 200 -240 VAC 12A 50-60 Hz
POWER SUPPL
Y 1
!
!
POWER SUPPLY 2
!
!
POWER SUPPL
Y3
!
!
POWER SUPPL
Y4
!
!
!
!
FC4
32
FC4
32
7
6
5
4
3
2
1
0
15
14
13
12
11
10
9
8
56-0000590-01Rev A
!
FC4
16
CP4
Link
10/10 0 Mb/s
Active CP
!
I O I O IRS - 232
CP4
Link
10/10 0 Mb/s
Active CP
!
I O I O IRS - 232
7
6
5
4
3
2
1
0
15
14
13
12
11
10
9
8
56-0000590-01RevA
!
FC4
16
12345678910
24
0
25
1
26
2
27
3
28
4
29
5
30
6
31
7
32
8
33
9
34
10
35
11
36
12
37
13
38
14
39
15
40
16
41
17
42
18
43
19
44
20
45
21
46
22
47
23
!
1
25223a
2
3
4
Figure 5 Installing an FC4–48 Port Blade
Callouts
1. SAN Director chassis 3. Upper ejector
2. FC4–48 4. Lower ejector
5. If installing the FC4–48, go to step 6.
For FC4–16 and FC4–32 models (see Figure 4).
a. Push the handles toward the center of the port blade, closing
theejectors.
b. Verify that the handle’s levering action properly seats the port
blade in the slot.
6.For the FC4–48:
Adjust the ejectors to the closed position (see Figure 5) by pulling
them away from the center of the port blade.
7. Tighten the thumb screw inside each handle using the Phillips
screw driver.
IMPORTANT:
Theupperandlowerthumbscrewsmustbecompletely
tightened, and the upper and lower ejectors must be in the
closed position for the FC4–48 to power on.
8. If installing the FC4–48, go to step 9.
For FC4–16 and FC4–32 models (see Figure 4):
a. To power on the port blade, move up the slider switch in the
top ejector.
b. Verify that the slider switch covers the thumbscrew.
9. For the FC4–48:
Verify that the power LED on the port blade displays a steady
green light (it might require a few seconds to turn on). If it does
not turn on, ensure that the port blade is firmly seated and that the
thumb screws are tight.
The LED patterns might temporarily change during POST and other
diagnostic tests.
10. Install SFP transceivers and cables in the port blade, as required.
11. Refer to the HP StorageWorks SAN Director installation guide for
different ways to manage cables, including:
• Routing directly down, through the cable management tray,
instead of across adjacent blades to keep LEDs visible.
•Insta
lling cable channels on the sides of the cabinet
•Insta
lling patch panels
IMPORTANT:
Disassembling any part of the port blades voids the part
warranty and regulatory certifications. There are no
user-serviceable parts inside the port blade.
Waste Electrical and Electronic
Equipment (WEEE) directive
Page 4