HPFI Nexstep 752 User manual

Nexstep Model 752
CARE & CLEANING:
1. This chair was designed to seat and support only 1 person.
2. All bolts, screws and knobs must be securely tightened prior to use.
3. Check that all bolts, screws and knobs are tight every 3 months or as needed.
4. Take care not to overtighten the back tilt knob when increasing or decreasing tilt tension.
5. Responsibly dispose of packing materials. The plastic covering should not be used as a toy or a head
covering as suocation may result.
6. Only use this chair for its intended purpose. Do not use as a step ladder.
7. Use a mild detergent for cleaning.
FEATURES:
• PNEUMATICSEATHEIGHTADJUSTMENT
Toraisetheseatheight,removepressurefromseatandpull
uponLever(1).Tolowerseatheight,sitinthechairand
pulluponLever(1).
• SYNCHROTILT
Tolock,returnchairtotheuprightpositionandpushLever
(1)in.Tounlock,pullLever(1)out.
• TILTADJUSTMENT
Foroptimumcomfort,thischairisequippedwithan
adjustmentthatwillallowyoutochangethetensionofthe
tiltingfeature.TurntheKnob(2)clockwisetoincrease
tension.TurntheKnob(2)counter-clockwisetodecrease
(ease)thetension.
NOTE: Becarefultonotcompletelyloosenthebacktilt
adjustmentKnob(2).
• ARMHEIGHTADJUSTMENT
ToadjusttheheightoftheArms(3),pushthebuttononthe
sideoftheArms(3)in.Releasethebuttonstolockthe
Arms(3)atthedesiredheight.
(3)
(1) (2)
©HPFi 1104 Bedford Street High Point, NC 27263 www.hpfi.com (p) 800.447.3462 (f) 800.231.6784

our Customer Service Department at 1-800-447-3462, ext. 2120.
High Point Furniture Industries
hp.com
Nexstep Model 752
Assembly Instructions
STEP 1 STEP 3
STEP 4 STEP 5
x4
4
10
12
5
9x3
11
12
4
3
1
STEP 2
7
8
x3
5
6L
6R
x3
7x3
x3
12
8
x5
STEP 6
Insert five Casters (2) into Base (1),
push hard until you feel or hear the
Caster (2) snap into place.
Align holes of Arms (6L & 6R) with holes
of Seat Cushion (5), secure Arms (6L &
6R) using three Arm Screws (7) and
three Flat Washers (8) for each arm.
Attach Seat Plate (4) to Seat Cushion (5)
with the arrow towards the front of the
chair, using four Seat Plate Screws (11).
Attach Back Support (11) to rear of Seat
Plate (4) using three Back Support
Screws (9).
Insert Pneumatic Cylinder (3) into Base
(1), place the assembled seat on top of
Pneumatic Cylinder (3) and apply
downward pressure.
ATTENTION: MAKE SURE ALL
SCREWS ARE FULLY TIGHTENED
BEFORE USING CHAIR.
FULLY TIGHTEN ALL SCREWS
WITH THE ALLEN WRENCH (12)
FULLY TIGHTEN ALL SCREWS
WITH THE ALLEN WRENCH (12)
FULLY TIGHTEN ALL SCREWS
WITH THE ALLEN WRENCH (12)
1
2
If you have any diculty with this installation/assembly, please contact our Customer Service department at
1-800-447-3462, ext. 2120.
Nexstep Model 752
Assembly Instructions
©HPFi 1104 Bedford Street High Point, NC 27263 www.hpfi.com (p) 800.447.3462 (f) 800.231.6784