HRS DPX-05545 User manual

HRS DAMPING PLATE DPX
Introduction
Thank you for purchasing the Harmonic Resolution Systems (HRS) Damping Plate DPX. When used properly, it will
give you many years of superior musical or video signal reproduction. The HRS Damping Plates significantly reduce
the negative impact of air and structure borne vibration on your audio or video component performance. The HRS
Damping Plates are a perfect match for the HRS Isolation Base. While the damping plates work to significantly reduce
air-borne vibration, the isolation base significantly reduces the harmful effects of structure-borne vibration.
Safety Instructions IMPORTANT!
Do not place any tall objects on the damping plate. A tall object is any object that has a height greater than its own
width or length. The object may become unstable and tip over.
Do not place the damping plate over ventilation holes of any electronic component. The ventilation holes will be
blocked and the internal operating temperature of the component will be increased.
Setup Instructions
The HRS Damping Plates should be placed directly on top of an electronic component chassis or speaker cabinet with
the soft side of the damping plate in contact with the component surface. The greater the surface area covered by the
damping plates the greater the improvement in audio/video performance.
Note that porous dark paints can attract and retain moisture from the HRS Damping Plate rubber, and that this can cause
slight discoloration over time. If minor cosmetic changes in surface finish are a concern, HRS does not recommend
using the Damping Plates on those surfaces. Please refer to “Care and Maintenance” below for more information.
Specifications
HRS Damping Plate Physical Characteristics
Model Number
Dimensions - inches (cm)
Weight - pounds (Kg)
DPX-05545
5.5 x 4.5 x 1.3
(14.0 x 11.4 x 3.3)
2.6 (1.2)
DPX-09545
9.5 x 4.5 x 1.3
(24.1 x 11.4 x 3.3)
4.6 (2.1)
DPX-14545
14.5 x 4.5 x 1.3
(36.8 x 11.4 x 3.3)
7.0 (3.2)
Care and Maintenance
The HRS Damping Plates are a very low maintenance item that will provide many years of trouble free performance by
applying these basic care instructions.
Clean the Damping Plates using a lint-free soft (non-abrasive) cloth. Use a damp cloth with water or mild soap if
required. Do not spray with or immerse in water.
Porous, flat (no sheen), dark, paint colors tend to attract and retain moisture from rubber contact surfaces after
prolonged exposure. This causes slight discoloration. This can usually be reduced or removed by gently wiping the
surface with a soft black cloth damp with Pledge Multi-Surface cleaner (836661). Allow the cleaner to dry completely
between wipes. HRS recommends testing this process on a small area of the chassis first to confirm that it will not leave
a residue or damage the paint.

Warnings!
Do not place objects with sharp or pointed feet directly on the damping plates as they may cause nicks, scratches or
gouges in the surface.
Do not use an abrasive cleaner or abrasive sponge to clean the damping plates, as they may scratch the metallic surface.
Do not wash with any solvent based cleaning solutions.
Prolonged contact with the rubber pads of the damping plates can cause slight discoloration on black painted surfaces.
Warranty
Limited Five Year Warranty
Harmonic Resolution Systems Inc. warrants to the purchaser that each HRS Damping Plate DPX is free of
manufacturing defects for a period of five (5) years from the date of purchase. This warranty is subject to the following
conditions and limitations.
1. A copy of the original purchase receipt from a certified Harmonic Resolution Systems Inc. authorized retailer is
used to verify the date of original purchase and ownership.
2. This warranty is void and inapplicable if the product has been handled other than in accordance with the instruction
specified within this document, abuse or misused, damaged by accident or neglect or in being transported, or the
defect is due to the product being tampered with, modified or repaired by anyone other then Harmonic Resolution
Systems.
3. Warranty does not cover normal recommended care and maintenance.
4. Harmonic Resolution Systems Inc. shall not be responsible in any way for consequential or indirect damages or
liabilities resulting from the use of the product covered herein or resulting from any breach of this warranty or any
implied warranty relating to said product.
During this period, Harmonic Resolution Systems Inc. will repair or replace any defective components free of charge.
A Return Authorization Number (RA Number) is required before any product is returned to Harmonic Resolution
Systems Inc. for any reason. This number must be visible on the exterior of the shipping container(s) for Harmonic
Resolution Systems Inc. to accept the return.
Units shipped to Harmonic Resolution Systems Inc. without a visible RA Number on the exterior of the shipping
container(s) are subject to be returned to the sender, freight collect.
Units to be repaired by Harmonic Resolution Systems Inc. must be sent shipping and insurance prepaid by the original
purchaser in the original packaging material. A returned product should be accompanied by a written description of the
defect. Repaired units will be returned by Harmonic Resolution System Inc shipping and insurance prepaid.
All other warranties or conditions either written or implied are void.
(MADE IN USA)
All Harmonic Resolution Systems Inc. products are 100% Made In The United States of America by
skilled craftsmen using only the finest materials and our personal dedication to the highest
workmanship standards.
HARMONIC RESOLUTION SYSTEMS INC.
2495 Main Street, Suite 227
Buffalo, NY 14214
Telephone: [phone]
Web: www.AVisolation.com
E-mail: [e-mail]