Huace Navigation Technology LT500XYZ Quick start guide

LT500XYZ Operational description
1. LT500XYZ Block Diagram
2. Operating steps：
I. Charging
II. Fix TF card/SIM card/battery
III．Turn on the collector
IV. Connect to PC to install application or data
V. Collect GIS data with internal GPS and GIS application
VI. Upload data
Charging
Insert the Li-ion battery into the battery charger to charge.
Remark: USB cable can also be used to charge the receiver. When normally charged, there is charging
icon in the screen if receiver is off and there is charging icon to the top right corner in the screen
if receiver is on.
Fix TF card/SIM card/Battery
1、Turn the back cover screw to the open position according to the instruction on the back
cover and take off the back cover
2、Fix the SIM card and TF card according to the instruction in the battery cabin
3、Fix the battery and turn the back cover screw to the lock position according to the
instruction on the back cover

Turn on/off collector
1、Make sure there is enough power in battery, or connect receiver to PC with USB cable
(with battery in).
2、Press power button for 3～5 seconds to turn on(until the boot screen appears)/ turn off.
Remark: if receiver is down, press the reset button in the bottom of receiver to reset.
Connect to PC
1、Make sure Microsoft ActiveSync application has been installed in PC.
2、Connect receiver to PC with USB cable.
3、ActiveSync application connect receiver and PC automatically. There is icon
appears in the tool bar of PC and ‘Synchronization Setup Wizard’ appears meantime, click
‘Cancel’.
4、Click ‘Browse’to check the files in receiver, then transfer data between PC and
receiver.
Install Application
1、Make sure Odin is connect with PC via ActiveSync.
2、Click install file on PC to start the installation. If the install file is compatible for mobile
device, copy the file into Odin and click to start the installation.
3、Select installation directory in S20 （‘Flash Storage’ is suggested）, click ‘install’.
Remark: it’s suggested to install the application in ‘Flash Storage’, save data in TF card.
Use GPS
Set COM port as COM6 and baud rate as 57600 in application.
Use Camera
Select ‘Start->Picture & Video’，select ‘Camera’or camera icon to take photos.
Click screen and select‘OK’to exit.
Wireless Connection（Bluetooth/GPRS/WIFI）
Bluetooth
1、Select ‘Start->Settings->Connections->Wireless management’, click the icon
on the right of ‘Bluetooth’to activating the Bluetooth device.
2、Select ‘Start-> Settings-> Bluetooth’, click ‘Add new device…’, system will
search available Bluetooth device. Select the device in refurbished list and click ‘Next’
in the bottom right corner, input password.
3、Select ‘Next’, input password in external Bluetooth device and finish the connection.
Remark: The password is used to the connection between Bluetooth devices and can be setup freely,
such as ‘1234’.
GPRS
1、Make sure there's SIM card in receiver.
1、
Press camera key to take photos. Click screen and select‘OK’to exit.2、

2、Select ‘Start->Settings->Connections->Connections’.
3、Click ‘Add a new modem connection’.
4、Input connection name, select ‘Cellular Line(GPRS)’, click ‘Next’.
5、Input ‘cmnet’, click ‘Next’.
6、Click ‘Finish’and add new connection successfully.
7、Click ‘Manage existing connections’.
8、Click on the new connection for a while and select ‘Connect’.
9、There is GPRS identifier on the signal icon on the top right corner, indicates the
successful connection.
WIFI
1、Select 'Start->Settings->Connections->Wi-Fi'；
2、Click ‘Search for Networks’, select a network that listed. Follow the installation
guide to input password and finish the connection.
3. Useful Settings
Screen response
Select ‘Start-> Settings-> System-> Screen’, click ‘Align Screen’icon and follow the
guide to align the screen.
Adjust backlight
Select ‘Start-> Settings-> System-> Backlight', adjust backlight status according to the
guild.
Auto power off
Select ‘Start-> Settings-> System-> Power-> Advanced’, set the power off time in
different conditions.
Remove programs
Select ‘Start-> Settings-> System-> Remove Programs’, select the program in the list
and click ‘OK’to remove.
Fall alarm
Select ‘Start-> Settings-> System-> Motion Sensor’, select ‘Fall Alarm’, check or
not the function of sharp warning sound when Odin is dropped. You can also open or
close the ‘Screen rotation’function in this menu.
Restore Factory Defaults
Select ‘Start-> Settings-> System-> Restore Factory Defaults’, restore factory defaults
settings according to the guide.
Caution: Restore factory defaults settings, all the data and programs will be lost.