HUANUO HNCM9 User manual

English ------------------------------- 01-05
Deutsch ------------------------------- 06-10
Français ------------------------------- 11-15
Español ------------------------------- 16-20
Italiano ------------------------------- 21-25
Model: HNCM9
Thank you for choosing this HUANUO product! At HUANUO we strive to
provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact us at
Technical Support:
44-808-196-3874 Mon-Fri 2pm - 10pm (UTC)
Other Info:
[email protected] (DE/UK/FR/IT/ES/NL/SE/AU/PL)
V3.0
Monitor Stand Instruction Manual

1
!
Supplied Par ts List
CAUTION!
DO not install on a structure that is prone to vibration, movement or chance of impact. Reinforce
the structure as required before installation. Don't use the product on particle board.
Pole Set
a (x1)
VESA Plate
e (x1)
Grommet Base
m (x1)
WARNING
M4x12 Thumb Bolt
q (x4)
M4x30 Bolt
r (x4) M4 Spacer s (x4)
Wire Clip
n1 (x3) Wire Clip
n2 (x2) Allen Key
o (x1)
Support Plate
j (x1) M10 Washer k (x1) Spring Washer l (x1)
M5x14 Bolt
f (x3) M8x12 Bolt
g (x2) Nut h (x1)
“C” Clamp
b (x1) “C” Clamp Brace
c (x1) Swivel Arm
d (x1)
This monitor desktop mount must be securely
attached to the horizontal desk. If the mount is
not properly installed it may fall, resulting in
possible injury and/or damage.
Not Included
Phillips Screwdriver
Soft Pad
w1(x1) Soft Pad
w2(x1)

2
Pre-Assembly the Pole Set
Remove the grub screws by provided
Allen Key (o).
Connect the poles by threads as below
diagram.
Install the grub screws and fasten them by
provided Allen Key(o).

Step 1
3
Option A: Desk Clamp Install
Figure 1
Figure 3Figure 2
Option B: Grommet Base Install
Figure 4
Figure 5
g
o
b
Plastic Knob
1. Install the “C”-Clamp Brace(c) to the Pole (a) using 3pcs M5x14
Bolts(f), and tighten using the Allen Key(o), see Figure 1.
2. C-clamp (b) was mounted on the Clamp assembly according to the
thickness of the table top. Thickness can be changed to three
positions. Respectively,1: 11-74 mm(0.43"-2.95");2: 26-89
mm(1"-3.5");
3: 41-104 mm(1.6"-4").
Use 2 M8x12 bolts (g) and tighten them with an Allen wrench (o), see
Figure 2.
3. Use plastic knob to tighten C-clamp to the table, see Figure 3.
1 2 3
Install the Pole to the Desktop
If the existing grommet hole comes with
a plastic protector, remove it to ensure a
flat surface before installing the desk
mount.
1. Install the Grommet Base Plate(m) to
the Pole(a) using 3pcs M5x14 Bolts(f),
and tighten using the Allen Key(o), see
Figure 4.
2. Position the Pole(a) on the mounting
surface and secure using the Support
Plate (j), M10 Washer(k), Spring
Washer(l) and plastic knob. Fasten the
plastic knob using provided Wrench(p),
see Figure 5.
Existing Grommet Hole Installation
j
k
l
Phillips Screwdriver
a
fc
ow1
a
m
fo
w2

4
Step 2
d
on1
n2
Install Swivel Arm(d) to the
Pole(a). Fasten the bolt with
supplied Allen Key(o). Attach
the Wire Clip(n1,n2) to the
Pole(a) and Swivel Arm(d).
For Monitor with Flat Back For Monitor with Curved or Recessed Back
Install Arm to the Pole

5