HUANUO HNWSS1 User manual

V1.0
Model: HNWSS1
Thank you for choosing this HUANUO product! At HUANUO
we strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.huanuoav.com/reviews if you
are satisfied. Should you have any issues, please don't
hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Website:
www.huanuoav.com
Monitor Wall Mount
Instruction Manual V1.0

• Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
contact our customer service at [email protected]
CAUTION: Avoid potential personal injuries and property damage!
• This product is designed for use in wood stud, solid concrete, concrete block
and brick walls - DO NOT install into drywall alone.
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and percussion
prohibited. Also it is strictly prohibited to dismantle without professionals. Please
return to the manufacturer or hand over to professional agencies if the product is
abandoned.
• The wall must be capable of supporting three times the weight of the total load
(the mount, the monitor and all accessories weight).
Minimum VESA pattern: 75mm/3 in.(W)x75mm/3 in.(H)
MAX:200mm/
7.9
in.
MAX:200mm/7.9 in.
Check the VESA Pattern of Your Monitor before the Installation
IMPORTANT SAFETY INFORMATION
If your Monitor VESA is greater than 200x200 mm/8x8 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
100 mm ≈ 4 in
75 mm ≈ 3 in
200 mm ≈ 7 7/8 in
01 11
100908070605
04
0302
Weight Restrictions
3.3-17.6 lbs.
(1.5-8.0 kg)
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage and or injury.
If your monitor weighs
more, this mount is NOT
compatible.
WARNING

3/8 in.(10mm)
Concrete Drill
Awl
Stud Finder Tape Measure Pencil Drill
5/32 in.(4 mm)
Wood Drill 3/8in.(10mm)
Socket Wrench
Phillips
Screwdriver
Warning: This product contains small items that could be a choking hazard if
swallowed.
• Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, contact our
Product Support line at 1-800-556-0533 or customer service at
[email protected]
• Please note: Not all hardware included in this package will be used.
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
M5x12 Bolt
M-H x8
M5 Nut
M-G x8
Level
01 11
100908070605
04
0302
Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
Verify Your Wall Construction
If you are not sure the wall
construction, please
contact our product
support line at
1-800-556-0533 or
customer service at
[email protected]
[02] X1
Faceplate
[03] x2 [04] x 2
Extender Bracket

D4
M-E x4
M4 x 16mm
M-B x4
M5 x 16mm
M-C x4
M6 x 16mm
M-D x4
M5
M4
M6
M4 x 12mm
M-A x4
Spacers [If needed]
[Only one bolt size fits your monitor]
Washer
Monitor Bolts
Note: The bolts are shown in accordance with the actual size
Note: The washer and spacers are shown in accordance with the actual size
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
05
07
06
Arm Assembly/Wall Plate
[01] x1
M5
M-F x4
Washer Spacer
Lag Screw
M6.3x55mm
W-A x3
01 11
100908070605
04
0302

BC
For VESA hole pattern:
2.95 in.x2.95 in.(75x75mm)
3.94 in.x3.94 in.(100x100mm)
For VESA hole pattern:
7.87 in.x7.87 in.(200x200mm)
For VESA hole pattern:
7.87 in.x3.94 in.( 200x100mm)
BCA
Choose the Combination that Applies to Your VESA Hole
Pattern
Attach the extender brackets to faceplate
Step 1
(3.94 in.)
(3.94 in.)
(2.95 in.)
(2.95 in.)
(7.87 in.)
(7.87 in.)
(7.87 in.)
(3.94 in.)
Washer
W-B x3
Supplied Parts and Hardware for Step 4 and Step 5
Wall Anchor
M10x45mm
W-C x3
[03]
[03]
[04]
[04]
[02]
M-G
M-H
M-G M-H
[03]
[02]
01 11
100908070605
04
0302
Bolt
I x1
Large Allen Key
15/64in.(6mm)
T2 x1
[03]
[04]
[04]
Small Allen Key
5/32in.(4mm)
T1 x1

（If Needed）
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination.
We recommend thread engagement by at least 5 turns.
-Too short will not hold the monitor.
-Too long will damage the monitor.
Too Short Too Long Correct Correct
Select Monitor Bolts
M5
M4
Only one bolt size fits your monitor.
Secure the Faceplate [02] or Faceplate [02] with
Extender Brackets [03 and 04] to Monitor
Step 2
CAUTION: Ensure the faceplate [02] or
faceplate [02] with extender brackets [03
and 04] is EQUALLY CENTERED on your
monitor and securely fastened in place.
(If Needed)
Option A:(For Flat Back Monitor)
M-A/M-C/M-D
M-E
M-F
01 11
1009080706
05
04
0302
M6

01 11
10090807
0605
04
0302
For cable interference or inset holes, use
spacers to create extra space between
the monitor and faceplate
Option D
M-F
Option B (For Round Back Monitor)
Spacers may be necessary for 2 holes ONLY.
Option C (For Monitor with A “Bump”)
(If Needed)
(If Needed)
M-B/M-C/M-D
M-E
M-F
M-F
(If Needed)
M-A/M-C
/M-D
M-E
M-F
M-F
M-B/M-C/M-D
M-E
(If Needed)
(If Needed)
M-B/M-C/M-D
M-E
M-F

WARNING:
Step 3A Wood Stud Option
3A-1
3A-2
Position the arm assembly/wall plate
[01] at your desired height and line
up the holes with your stud center
line. Level the arm assembly/wall
plate [01] and mark the holes.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½
in. (38 x 89 mm)
● Stud center must be verified
●Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws
[W-A] and washers [W-B]. Tighten the lag screws [W-A] only until the washers [W-B] are
pulled firmly against the arm assembly/wall plate [01].
●Ensure the arm assembly/wall plate [01] is securely fastened to the wall
before continuing to the next step.
●DO NOT USE ANCHOR [W-C] FOR THIS STEP
Use a stud finder(not includ-
ed) to locate wood studs or
use an awl (not included) to
verify the edges. Mark the
edge and center locations.
Awl
(Not lncluded)
UP
Step 3 Attach the Arm Assembly/Wall Plate [01] to Wall
For wood stud installation, follow STEP 3A
For concrete installation, follow STEP 3B
X
01 11
100908
070605
04
0302

WARNING:
●Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [W-A]. Tighten the lag screws [W-A] only until the washers [W-B] are pulled firmly
against the wall plate.
●Ensure the arm assembly/wall plate [01] is securely fastened to the
wall before continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the wall plate directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks
Wall
Anchor
W-C
Step 3B Solid Concrete or Concrete Block Option
3A-3
3A-4
Drill 3 pilot holes using a 5/32 in.(4 mm)
diameter drill bit. Make sure the depth is
not less than 2 11/64 in.(55mm).
3/8 in.(10 mm)
Socket Wrench
(Not lncluded)
ø5/32 in.(4mm)
2 11/64 in.(55mm)
Install the arm assembly/wall plate
[01] using lag screws [W-A] and
washers [W-B]. Tighten the lag
screws [W-A] only until the washers
[W-B] are pulled firmly against the
wall plate.
UP
W-A
W-B
01 11
1009
08070605
04
0302

3/8 in.(10 mm)
Socket Wrench
(Not lncluded)
ø3/8 in.(10mm)
2 23/64 in.(60mm)
Drill 3 pilot holes using a 3/8
in.(10mm) diameter drill bit. Make
sure the depth is not less than 2
23/64 in.(60mm). Never drill into the
mortar between blocks.
Use the hammer to knock anchors
[W-C] into the wall. Be sure the
anchors [W-C] are seated flush
with the concrete surface.
Install arm assembly/wall plate [01]
using lag screws [W-A], washers [W-B]
and anchors [W-C]. Tighten the lag
screws [W-A] only until the washers
[W-B] are pulled firmly against the wall
plate. DO NOT over-tighten the lag
screws [W-A].
3A-2
3A-3
Position arm
assembly/wall plate [01]
at your desired height,
level arm assembly/wall
plate [01] and mark the
pilot hole locations.
You may need
assistance with this step.
3A-4
UP
3B-1
W-B
01 11
10
0908070605
04
0302
UP
W-A

You may need
assistance with this step.
Step 4. Hang the Monitor to the Mount
I
T1
(Small Allen Key)
01 11
100908070605
04
0302
Be sure to keep the arm in horizontal
position during adjustment. Or else, it
would be difficult to adjust the mount or
damage the mount.
1. If the monitor can stay at the desired
height by itself, no adjustment needed.
2. If the monitor rises up, press the arm to
keep it in horizontal position and then use
the Allen Key [T2] to turn the bolt
clockwise(“-” direction) to reduce tension
of the arm only until the monitor can stay at
the desired height by itself.
3. If the monitor falls down, lift the arm to
keep it in horizontal position and then use
the Allen Key [T2] to turn the bolt
counter-clockwise (“+” direction) to
increase tension of the arm only until the
monitor can stay at the desired height by
itself.
Step 5. Gas Spring Tension and Tilt Adjustment
Or
Gas Spring Tension Adjustment
Gas Spring Tension Adjustment
Tilt Adjustment
Tilt Adjustment
1. Slightly loosen the pre-assembled bolt [S].
2. Adjust the monitor to your desired tilt angle.
3. re-tighten the bolt [S] to secure the monitor in place.
T2
(Large Allen Key)
S

Step 6. Route the Cables along the Arm
Angle Adjustment
01 11
100908070605
04
0302