Huawei ATOM GPS NE08E User manual

HUAWEI TECHNOLOGIES CO., LTD.
ATOM GPS (Indoor NE08s and AE 905S)
Quick Installation Guide
Issue: 01
Date: 2016-12-20

Copyright © Huawei Technologies Co., Ltd. 2016. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://www.huawei.com
Email:
[email protected]

Installation Flow
PrecautionsPage 1
Introduction to the
ATOM GPS
Page 2
Installing the GPS
Satellite Antenna System
Pages
4-5
End
Start
Preparation
For
Installation
Tools for InstallationPage 1
Appendixes
Pages
7-8
Assembling OT
Terminals
Page 7
Perform power-on checkPage 6
Requirements for GPS
Antenna Installation
Positions
Page 8
Overall Installation EffectPage 3
0

1
Precautions
•This document aims to provide simple and distinctive guidelines for hardware installation.
•This document does not describe operations for the pre-delivery installation. Instead, this document
describers only the operations for on-site installation.
•This document describes how to connect the ATOM GPS to the GPS Satellite Antenna System. The ATOM
GPS consists of the indoor NE08E and AE 905S. This example uses the NE08E-S6.
•For requirements on the GPS installation, see GPS Satellite Antenna System Quick Installation Guide.
•For requirements on the GPS antenna position, see Appendixes 2.
Measuring tape Phillips screwdriver Flat-head screwdriver Adjustable WrenchLevel
Ratchet crimp tool Cable CutterWire stripper Diagonal pliersPaper knife
Multimeter ESD gloves Insulation tape
Tools for Installation
Ladder or ladder truck
NOTE
•EHS requirements: The installation personnel should wear safety belts, helmets, shoes, and gloves for
climb operations.
•Exercise caution when touching the device with the high temperature identification to avoid scalding.
•When installing or maintaining fibers, do not look into the optical port without eye protection. The infrared
laser emitted by the optical interfaces can cause permanent eye damage.
Use cables delivered with Huawei devices or cables complying with Huawei standards.
NOTE

2
Introduction to the ATOM GPS
Before inserting an AE 905S to an optical interface, lock the
ejector lever. Before removing an AE 905S from an optical
interface, loosen the ejector lever.
Although the AE 905S can be inserted into an optical
interface, it cannot be installed on an NED1EG2 board.
If you need to install two AE 905Ss on a device, separately
installing them on the optical interfaces of two boards is
recommended.If you need to install two AE 905Ss on the
same board, inserting the modules at an interval of at least
four optical interfaces is recommended.
Loosen the ejector lever.
a Indoor NE08E (Example:NE08E-S6)
AE 905S
b
10
Optical interface Alarm interface
Power supply interface Clock interface
Time interface
Antistatic jack interface
Optical interface
NM interface
(Console interface)
PGND point
Electrical interface
Lock the ejector lever.
NOTE
10

3
Overall Installation Effect
a Typical Scenario 1
Typical Scenario 2
b
NE08E
GPS antenna
lightning protection
component
Feeder
Route the feeder along the cable rack that is mounted on the wall and use feeder fasteners to fix the feeder.
The interval between feeder fasteners is 2.5 m.
Route the feeder along the cable rack that is mounted on the wall and use feeder fasteners to fix the feeder.
The interval between feeder fasteners is 2.5 m.
NE08E
GPS antenna
lightning protection
component
Feeder

Standalone Deployment of a Lightning Protection Component
4
Install the dual-female conversion adapter on
the Protect interface of the lightning protection
component.
Connect one end of the coaxial cable to the RF
OUT interface of the amplifier, and use the
wrench to secure the joint.
Connect one end of the coaxial cable to the
Protect interface of the lightning protection
component, and use a wrench to secure the
joint.
For requirements on the GPS installation, see GPS Satellite Antenna System Quick Installation Guide.
For requirements on the GPS antenna position, see Appendixes 2.
This document describes how to connect the ATOM GPS to the GPS.
Deploy amplifiers based on the GPS feeder length. Deploy one amplifier if the feeder length exceeds 80 m.
Dual-female
conversion
adapter
Lightning
protection
component
Protect
Surge
Installing the GPS Satellite Antenna System
Deployment of a Lightning Protection Component Together with an Amplifier
Surge
Connect the RF IN interface of the amplifier to the
Protect interface of the lightning protection
component, and use a wrench to secure the joint.
Lightning
protection
component Protect
Amplifier
Ground bar
Install the ground cable of the lightning
protection component.
At the joint between the coaxial cable and the
Protect interface of the lightning protection
component or the RF OUT interface of the
amplifier, implement 1+3+3 waterproof
protection. Use one cable tie on each end of
the tape to secure the adhesive tape.
NOTE
Wrap one layer
of insulation
tape.
Wrap three layers
of waterproof
tapes.
Wrap three layers
of insulation
tapes.
Use one
cable tie on
each end.

Install the GPS feeder by connecting one end
of the feeder to the Surge interface of the
lightning protection component and the other
end to the GPS antenna. Use the wrench to
secure the joint.
5
Implement 1+3+3 waterproof protection. Use
one cable tie on each end of the tape to
secure the adhesive tape.
•Implement waterproof protection for the
feeder-and-lightning-protection-surge joint.
•Implement waterproof protection for the
feeder-and-GPS-antenna-N joint.
Insert the AE 905S into an optical interface of
the NE08E device, with the wrench on the AE
905S being locked.
Connect the other end of the coaxial cable to
the AE 905S.
The coaxial cable must be routed without affecting the
cabling of neighboring boards.
Do not connect the coaxial cable to any AE 905S
inserted into an optical interface adjacent to another
optical interface with an optical attenuation module.
Wrap one layer
of insulation
tape.
Wrap three layers
of waterproof
tapes.
Wrap three layers
of insulation
tapes.
Use one
cable tie on
each end.
For requirements on the GPS feeder joint production,
see GPS Satellite Antenna System Quick
Installation Guide.
NOTE
NOTE

6
Perform power-on check
1 Check the indicator of the AE 905S
the indicator
Status Description
Steady on (Green) The AE 905S module works properly.
Steady on (Red) The AE 905S module encounters a hardware
fault or overtemperature event.
Flashing at an interval of 1s
(Red) The frequency or time of the GPS is out of lock.
Flashing at an interval of 1s
(Green) The GE port is unavailable (not linked).
Off 1. The module is not running.
2. The module is not powered on.

7
1
Assembling OT Terminals
Material: OT terminals (ring terminals) , heat-shrinkable tube and cable.
Strip a part of the jacket off the cable to expose the
conductorwith a length of L1.
L1 = 23 mm to 25 mm
L1
Conductor
When stripping the jacket off the cable, do not
damage the metal conductor of the cable.
Press the end of the contact terminal on the
conductor by using the crimping tool.
Heat the heat-shrinkabletube by using a heat gun.
Lead the cable through the heat-shrinkable tube,
and then place the contact terminal on the
exposed conductor.
A: heat-shrinkable
B: OT terminals
•Close contact between the contact terminal and the end of
the jacket of the cable is required.
•When placing the contact terminal on the conductor
closely to the end of the jacket, ensure that the L2 part of
the conductor which sticks out of the contact terminal
cannot exceed 2 mm.
C: power cable
insulation layer
Heat gun
Do not overheat the heat shrink tube. Otherwise,
the insulation layer may be damaged.
CAUTION
CAUTION CAUTION
Appendixes